Study guide
3.1 Center of Gravity and Suspended Stability
NCCCO Rigger Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Certification and Exam Preparation
1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification
2 Identify and Measure the Load
2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling
3 Center of Gravity and Support Geometry
3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access
4 Route and Site Hazards
4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions
5 Team Duties and Communications
5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication
6 Equipment Requirements and Lift Planning
6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies
7 Balanced Sling Forces
7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand
8 Composite and Unequal Loads
8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing
9 Wire Rope, Chain and Metal Mesh Slings
9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal
10 Synthetic Rope, Web and Roundslings
10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers
11 Hitch Application and Sling Protection
11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection
12 Shackles, Hooks and Collector Hardware
12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels
13 Threaded Points and Adjustable Hardware
13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems
14 Compression Hardware and Rigging Blocks
14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving
15 Manual, Lever and Powered Hoists
15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls
16 Jacks, Rollers and Portable Supports
16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility
17 Structural Lifters and Clamps
17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters
18 Mechanical, Vacuum and Magnetic Devices
18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples
19 Inspection, Removal and Records
19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing
20 Lift Control, Rotation and Completion
20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment
21 Technical Standards and Crane Capacity
21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431
3.1 Center of Gravity and Suspended Stability
Key Takeaways Explain This Topic AI
External symmetry does not prove a composite load’s CG is centered.
Hook position over CG does not guarantee equal sling forces.
A trial lift checks the plan; it does not replace weight and CG determination.
Last updated: October 2026
Locate mass rather than appearance
The center of gravity (CG) is the point through which the resultant weight acts in the gravitational field used for ordinary rigging calculations. For a uniform, symmetrical body, it may coincide with the geometric center. For an assembled machine, hollow frame, vessel with internals or partly filled container, external symmetry does not establish its location.
In a freely suspended, static system supported from one hook, the resultant gravitational force acts beneath the suspension point. If the initial arrangement places that point away from the system CG, the load can translate or rotate as tension develops. The final attitude depends on the attachment geometry, sling lengths and restraints. Putting the hook above the estimated CG is necessary planning, but it does not by itself guarantee level attitude or equal sling forces.
Distinguish the CG of the payload from the CG of the complete suspended assembly . A heavy beam, asymmetric rigging or an offset handling device changes the assembly’s mass distribution. In a simple training model, rigging mass may be negligible or explicitly excluded. In an actual lift, the approved model must account for relevant masses and their positions.
Stable, neutral and unstable configurations
A simple body pivoting about a fixed horizontal suspension axis illustrates three conditions. If its CG lies below the axis, a small displacement raises the CG and gravity tends to return the body toward its resting orientation. If the CG lies on the axis, gravity provides no restoring moment in the ideal model. If the CG lies above the axis, a small displacement lowers the CG and gravity tends to increase the overturning movement.
- Simple pivot condition Gravitational response Handling consequence
- CG below pivot axis Restoring tendency Check that connections retain the load while it settles
- CG on pivot axis Little or no restoring tendency Orientation requires planned control
- CG above pivot axis Overturning tendency Provide an approved stable handling arrangement
These are model conditions, not a universal rule that any pick located below a CG makes every sling assembly instantly invert. A basket cradle, multiple restraints, a rigid handling frame or a complex suspension can behave differently. Evaluate the full support system and its possible rotation axes. A spreader changes force geometry but does not automatically prove a top-heavy load is stable within its lower slings.
Height matters independently of horizontal balance
A CG location along a skid tells how vertical reactions divide between two end supports. Its elevation tells how the body responds to tilt and lateral movement. Two machines can have the same total weight and longitudinal CG but different tipping resistance because one carries its heaviest mass higher.
For a body resting on supports, draw the support polygon through the effective support locations. The vertical projection of the CG must remain within the appropriate support region for static resistance to tipping, with the necessary planning margin. During acceleration, slope or rotation, additional forces change the stability assessment. An initial projection just inside the boundary is not a robust assurance of safe movement.
Consider a tall cabinet on two narrow skates. Its CG may be centered between them on a level floor, yet a turn, uneven joint or ramp changes the effective stability. Widening the approved support arrangement may help, but only if the cabinet base and handling equipment can accept that arrangement. Do not attach extra skates to cosmetic panels merely to enlarge a drawing’s triangle.
Confirm information through controlled verification
Manufacturer CG marks or drawings are useful only when they describe the actual configuration. A skid with an added transformer should not use the original bare-skid CG. Retained fluid, removed accessories and movable components require reconciliation. Mark the confirmed CG on the plan or load where practical so hook positioning uses a visible reference.
A trial lift verifies observed attitude and seating under the planned rigging. It does not replace a pre-lift CG determination. Raise only as necessary for the approved check, keep personnel clear and stop for unexpected tilt, migration or slack. Lower to stable supports before adjustments. Do not chase a shifting sling by hand beneath or beside a suspended load.
Interpreting a trial-lift result
Suppose a machine tilts toward its motor end as the slings take load. Possible causes include an off-center CG, inappropriate sling lengths, unequal pick elevations or a connection that is binding. The observation identifies a discrepancy; it does not establish a unique diagnosis. Return to support, compare the actual configuration and measurements with the plan, and revise the geometry deliberately.
A trial lift that looks level also does not prove equal sharing in every leg. A rigid four-point assembly can have different tensions while retaining level attitude. Use the applicable rated assembly, calculations and approved verification method. Load cells may assist when specified, but each reading must be interpreted as the force at its installed position.
The examination trap is to treat “balanced” as a synonym for “equal weight in all slings.” Static balance means forces and moments are in equilibrium. Unequal vertical shares can satisfy that condition when the CG is off center. The calculation chapters show how to derive those shares; this section establishes why locating and controlling the CG comes first.
Source: CCO Level II outline and reference materials .