Study guide
2.3 Composition, Structural Integrity and Special Handling
NCCCO Rigger Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Certification and Exam Preparation
1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification
2 Identify and Measure the Load
2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling
3 Center of Gravity and Support Geometry
3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access
4 Route and Site Hazards
4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions
5 Team Duties and Communications
5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication
6 Equipment Requirements and Lift Planning
6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies
7 Balanced Sling Forces
7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand
8 Composite and Unequal Loads
8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing
9 Wire Rope, Chain and Metal Mesh Slings
9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal
10 Synthetic Rope, Web and Roundslings
10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers
11 Hitch Application and Sling Protection
11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection
12 Shackles, Hooks and Collector Hardware
12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels
13 Threaded Points and Adjustable Hardware
13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems
14 Compression Hardware and Rigging Blocks
14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving
15 Manual, Lever and Powered Hoists
15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls
16 Jacks, Rollers and Portable Supports
16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility
17 Structural Lifters and Clamps
17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters
18 Mechanical, Vacuum and Magnetic Devices
18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples
19 Inspection, Removal and Records
19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing
20 Lift Control, Rotation and Completion
20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment
21 Technical Standards and Crane Capacity
21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431
2.3 Composition, Structural Integrity and Special Handling
Key Takeaways Explain This Topic AI
A sling’s working load limit does not rate the load’s lifting lug or shell.
Verify an attachment point’s permitted load and pull direction.
Moving internal masses can change center of gravity during a lift.
Last updated: October 2026
Capacity starts with the load’s condition
Structural integrity means the object and its attachment structure can transmit the planned lifting forces without failure. A sling rating tells how much the sling can carry in its rated configuration. It does not tell whether the cabinet panel, pipe wall, lifting lug or weld beneath the sling can carry the same force. A strong rigging system attached to a weak part of the load remains unsafe.
Identify the load’s materials and construction. A thin sheet-metal housing differs from its internal steel frame. A concrete panel differs from the approved embedded lifting anchor. A cast component may have localized brittle features, and a fabricated skid may rely on a particular sequence of attachments. Use drawings and manufacturer handling instructions to identify intended load paths rather than selecting the most convenient projection.
Look for deterioration or damage that changes the original assumptions: corrosion, cracking, missing fasteners, repairs, weakened welds, bent frames or damaged lifting inserts. Do not decide that a lifting point is acceptable simply because its hole still admits a shackle. The connection’s surrounding structure and the direction of force matter as much as the hole itself.
Separate approved picks from ordinary features
An attachment point intended for lifting has a defined relationship to the load and its rated handling condition. A handrail, process nozzle, mounting bracket or transport tie-down point may have no lifting rating. Even a genuine lifting point may be intended only for a component before assembly, not for the weight of the completed machine.
Ask what load and direction the attachment was designed to carry. A lug intended for an in-plane pull may be unsuitable for an out-of-plane sling. A tapped lifting hole needs appropriate thread engagement and surrounding material strength. A trunnion may require a particular sling position or restraint to prevent disengagement. Where the evidence is incomplete, obtain approval from the manufacturer or responsible qualified person before proceeding.
- Finding Why it changes the decision
- Thin shell beneath a choker Local compression may buckle or dent the shell
- Lug aligned with a different pull plane Side loading introduces bending not covered by the original rating
- Missing skid cross-member The assembly’s assumed load path has changed
- Lifting eye marked for motor only It may not carry the attached pump and base
- Repaired concrete insert area Original anchor data may no longer describe the condition
- Special handling is part of scope
Special handling requirements include keeping an item upright, limiting acceleration, protecting a finish, controlling liquid movement or preserving sensitive internal parts. These are design inputs. They should not be discovered after the load is already suspended.
A battery cabinet may have restrictions on tilt or require securing internal modules. A precision machine may have designated support points to prevent distortion. A thin-walled vessel may require a spreader with vertical lower slings so the shell is not squeezed by an inclined bridle. A fragile surface may need compatible contact materials while still meeting the sling’s bend and cut-protection requirements.
Do not assume a soft sling automatically protects every finish or prevents structural damage. Grit trapped beneath webbing can mark the surface. A wide sling can still crush a weak panel. Padding used for cosmetic protection may provide no rated resistance to cutting. Address surface protection, load strength and sling protection as separate needs.
Secure moving and loose parts
Doors, covers, counterweights, internal carriages and retained components can move when orientation changes. A movable mass shifts the center of gravity, changing load share and stability. Loose parts can become falling objects even when the principal load remains attached. Confirm which parts must be removed or restrained and how their restraint affects the total weight.
Consider a machine with a heavy slide positioned near one end. Calculating center of gravity with the slide centered does not describe the actual pick. If the slide travels during lifting, the calculation can change mid-operation. Locking it in the manufacturer’s approved transport position creates a controlled configuration; tying an improvised rope around it may not provide equivalent restraint.
Containers deserve similar attention. A crate may support cargo from below during shipping but have no capacity for lifting from its upper boards. A pallet can fail if straps create concentrated forces at unsupported deck edges. Identify whether the rigging carries the object directly, an approved handling container or an unverified package.
Inspection and escalation scenario
The crew finds a cracked weld beside a skid’s intended lifting lug. The crane and slings exceed the calculated demand, but the visible crack interrupts the load path into the skid. The rigger should stop the planned attachment, communicate the finding and obtain an approved repair or alternative method. Moving the sling to an adjacent unmarked rail does not resolve the defect.
Before authorizing motion, connect special handling information to the plan: maximum permitted tilt if specified, designated support locations, retained contents, restrained parts and protection materials. Explain these limits in the team briefing so the operator knows which motion would create a problem. If the owner’s instruction conflicts with the proposed geometry, redesign the rigging rather than treating the instruction as an optional preference.
Sources: CCO Level II scope , CCO reference manual .