Study guide
2.2 Load Weight, Density and Complete Inventories
NCCCO Rigger Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Certification and Exam Preparation
1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification
2 Identify and Measure the Load
2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling
3 Center of Gravity and Support Geometry
3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access
4 Route and Site Hazards
4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions
5 Team Duties and Communications
5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication
6 Equipment Requirements and Lift Planning
6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies
7 Balanced Sling Forces
7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand
8 Composite and Unequal Loads
8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing
9 Wire Rope, Chain and Metal Mesh Slings
9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal
10 Synthetic Rope, Web and Roundslings
10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers
11 Hitch Application and Sling Protection
11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection
12 Shackles, Hooks and Collector Hardware
12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels
13 Threaded Points and Adjustable Hardware
13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems
14 Compression Hardware and Rigging Blocks
14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving
15 Manual, Lever and Powered Hoists
15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls
16 Jacks, Rollers and Portable Supports
16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility
17 Structural Lifters and Clamps
17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters
18 Mechanical, Vacuum and Magnetic Devices
18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples
19 Inspection, Removal and Records
19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing
20 Lift Control, Rotation and Completion
20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment
21 Technical Standards and Crane Capacity
21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431
2.2 Load Weight, Density and Complete Inventories
Key Takeaways Explain This Topic AI
For uniform material, multiply volume by the appropriate given weight density.
For a hollow cylinder, subtract inner-cylinder volume from outer-cylinder volume.
An inclined-sling load cell reads tension, not just the vertical share.
Last updated: October 2026
Determine a defensible load weight
Load weight is the gravitational demand from the object being moved. Suspended system weight additionally includes slings, hardware, lifting devices and other items carried by the lifting equipment. Determine each inventory separately so the correct quantity reaches the correct calculation. Payload weight may control a beam’s rated load, while payload plus beam and rigging controls the crane’s suspended load.
Reliable information may come from manufacturer data, recognized calculations, shipping records, measurement or controlled weighing. OSHA’s crane operating provisions require determining that the load is within rated capacity and address recognized weight sources or methods. An estimate based on verified dimensions and appropriate material density is different from an unsupported guess. The quality of the inputs determines the quality of the estimate.
Ask whether a stated weight is dry, operating, shipping or installed weight. A shipping weight may include a pallet that will be removed. A dry vessel weight may exclude retained fluid. A motor drawing may omit a gearbox. Reconcile the record with what will be suspended, then account for uncertainties through an approved planning process.
Calculate volume before weight
For an object of uniform material density, weight is volume multiplied by the specified weight density. Use a density appropriate to the actual material and condition. Values in this lesson are given training inputs , not a material-identification method or permission to overlook internal contents.
- Shape Volume method Important distinction
- Rectangular solid Length × width × thickness Use consistent length units
- Solid cylinder π × radius squared × length Radius is half the diameter
Hollow cylinder Outer-cylinder volume minus inner-cylinder volume Use inner diameter, not wall thickness as a radius
Composite assembly Sum each component’s weight Avoid counting overlapping or removed pieces twice
For a plate 8 ft long, 4 ft wide and 1 inch thick, volume is 2.6667 cubic feet. With a supplied density of 490 lb per cubic foot, estimated plate weight is 2.6667 × 490 = 1,306.7 lb . Add actual attached hardware and any remaining components to obtain the assembly weight. Round the calculated result appropriately for the quality of the measurements; a tenth of a pound does not make an approximate density exact.
Hollow-pipe example
A pipe has a 12-inch outside diameter, a 10-inch inside diameter and a 20-ft length. Convert diameters to feet: 1 ft and 0.83333 ft. The annular cross-sectional area is π/4 × (1² − 0.83333²), approximately 0.239983 square feet. Volume is approximately 4.79966 cubic feet. Using a supplied density of 490 lb per cubic foot gives 2,351.8 lb .
Two common errors would be using a solid-cylinder volume, which includes the empty bore, or subtracting the diameters before squaring them. The area of the annulus is a difference of squared diameters. It is not the area of a solid cylinder whose diameter equals the wall’s combined thickness.
Add contents and accessories
Retained liquids, insulation, refractory, wiring, internal shafts, attached piping and shipping bracing can all change the lifted weight. Confirm contents through process isolation and the responsible owner. A tank that has been drained may still contain sludge. Opening equipment or releasing trapped material also introduces separate hazards that must be controlled before lifting.
A training inventory might contain a 12,000-lb machine, a 1,800-lb skid, 600 lb of retained contents and 400 lb of attached parts. Payload weight is 14,800 lb. If a lifting beam weighs 900 lb and lower rigging weighs 300 lb, the load beneath the upper connection is 16,000 lb. Additional upper rigging and the relevant crane block or load-line accounting must still be addressed according to the crane chart. The same item must not be added twice under different labels.
Recognize what a weighing result means
A load cell measures force in its particular connection. If installed in an inclined sling, it reads leg tension rather than the vertical load share. A crane display may estimate suspended load according to its system configuration. Neither measurement should be accepted without considering calibration, installed position, resolution and the manufacturer’s instructions.
If a load rests partly on the ground, the lifting equipment does not yet carry its entire weight. A partial pick reading cannot be used as total weight unless the method explicitly accounts for the remaining support reaction. Likewise, friction or a stuck connection can make the measured hoisting force exceed ordinary weight. Stop and resolve an unexpected force rather than pulling harder until the object breaks free.
Planning consequence
Suppose the verified payload is 14,800 lb, but the crew originally selected slings for the 12,000-lb bare machine. The correct response is to recalculate forces and component suitability for the complete payload. Choosing a stronger crane alone does not cure undersized lower rigging. Weight information must flow through every relevant connection, lifting device and destination support.
Sources: CCO Level II outline , OSHA crane operation .