Study guide

9.2 Alloy-Chain Assemblies and Approved Adjustment

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

9.2 Alloy-Chain Assemblies and Approved Adjustment

Key Takeaways Explain This Topic AI

Transport-chain strength does not establish overhead-lifting suitability.

Use only the shortener intended for the chain size and assembly.

Adjustment does not prove equal leg forces.

Last updated: October 2026

Select chain rated for overhead lifting

An alloy-steel chain sling is a manufactured or approved assembly of load chain and compatible fittings for lifting. Its rating comes from its grade, size, number of legs, angle, hitch and components. Do not select a transport chain for overhead lifting merely because it appears thick or has a high breaking strength.

Grades 80, 100 and 120 are common modern overhead-lifting products, but OSHA 1926.251 does not state that these are the only legally possible grades for every lifting assembly. The required decision is whether the actual alloy-chain assembly is identified and rated for overhead lifting under the applicable requirements and manufacturer instructions. A grade number or paint color alone is insufficient.

Grade 70 transport chain is generally supplied for load securement rather than overhead lifting. Its role in tie-down is separate from an approved lifting sling. Likewise, an ordinary utility chain or improvised welded connector does not become a rated sling when attached to a crane.

Match every fitting

Hooks, master links, connecting links, shortening devices and other attachments must be suitable for the chain system. OSHA construction provisions require fittings with capacity at least equal to the chain’s applicable demand and prohibit makeshift links or fasteners. A fitting that happens to fit through a link can still be incompatible in size, grade or load path.

  • Component Check
  • Master link Assembly capacity and fit in the upper hook
  • Connecting link Approved type, size and assembly procedure
  • Sling hook Correct chain connection and permitted load seating
  • Shortener Correct chain size and approved engagement
  • Chain leg Identification, condition and required effective reach

Use the rated assembly’s instructions when replacing or adjusting a component. A high-grade chain attached to a lower-rated fitting does not retain the chain’s full capacity. The assembly is limited by the applicable component and configuration demands.

Adjust through approved devices

A shortener changes the effective length using an approved chain-engagement arrangement. It must accept the correct link and maintain the intended bearing pattern. Some devices affect capacity or require particular engagement instructions; others are rated to retain capacity in specified use. Read the actual product instructions rather than applying one universal reduction.

Do not shorten by tying knots, bolting through links or using an unapproved hook or nail. Do not twist a chain leg to adjust its length. Twists change link bearing and can prevent the chain from aligning with the force. Make adjustments in the safely unloaded state unless the equipment is explicitly designed and approved for a particular loaded adjustment.

A turnbuckle or shortener can help establish the lengths required for a level lift. It does not automatically equalize all leg forces. Off-center loads still require correct reactions and geometry, and a multi-leg assembly still needs its approved rating basis.

Apply the right capacity table

Read the angle and leg count in the assembly table. A two-leg rating at 60 degrees from horizontal differs from a single-leg vertical rating. If the assembly is used at a flatter angle, use the corresponding permitted rating or approved analysis. Do not multiply the two-leg table value by two again.

A choker or basket arrangement may have separate capacity and engagement conditions. The load must seat in the hook’s bowl rather than on its tip or latch. Chain should not bear across a fitting in an unapproved bending pattern. A hook’s ability to rotate before loading does not authorize rotation under load unless it is designed for that service.

Capacity example

Assume a supplied table rates a particular two-leg chain assembly at 20,000 lb for 60-degree horizontal legs and 16,000 lb at 45 degrees. A complete supported load of 18,000 lb fits the first listed condition but exceeds the second. Shortening the upper geometry to clear a ceiling can therefore make the same assembly unsuitable. These are given training ratings, not a catalog chart to apply to another chain.

Temperature and surface contact

Chain can suit some abrasive or hot-service tasks, but its grade, fittings and manufacturer temperature instructions control. OSHA 1910.184 requires manufacturer capacity reductions for chain used above 600°F and permanent removal after exposure above 1,000°F. Particular products can have stricter conditions. Never heat chain to straighten a link or restore fit.

Chain can damage a finished surface or create high contact forces on thin material. Use an approved arrangement and compatible protection rather than assuming metal slings are suitable for any rugged-looking load. Protect the load and preserve the chain’s alignment as separate requirements.

Inspect every link and fitting, especially interlink bearing surfaces. Any observed stretch, distortion or cracking calls for removal/evaluation under the applicable criteria; a generic 5% stretch allowance is not safe permission. Required proof testing after manufacture or repair is a controlled qualification process, not a test the field crew performs by overloading the sling.

Sources: CCO reference materials , OSHA slings , CMCO chain-sling information .