Study guide
9.3 Metal-Mesh Slings: Selection, Contact and Removal
NCCCO Rigger Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Certification and Exam Preparation
1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification
2 Identify and Measure the Load
2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling
3 Center of Gravity and Support Geometry
3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access
4 Route and Site Hazards
4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions
5 Team Duties and Communications
5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication
6 Equipment Requirements and Lift Planning
6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies
7 Balanced Sling Forces
7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand
8 Composite and Unequal Loads
8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing
9 Wire Rope, Chain and Metal Mesh Slings
9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal
10 Synthetic Rope, Web and Roundslings
10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers
11 Hitch Application and Sling Protection
11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection
12 Shackles, Hooks and Collector Hardware
12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels
13 Threaded Points and Adjustable Hardware
13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems
14 Compression Hardware and Rigging Blocks
14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving
15 Manual, Lever and Powered Hoists
15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls
16 Jacks, Rollers and Portable Supports
16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility
17 Structural Lifters and Clamps
17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters
18 Mechanical, Vacuum and Magnetic Devices
18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples
19 Inspection, Removal and Records
19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing
20 Lift Control, Rotation and Completion
20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment
21 Technical Standards and Crane Capacity
21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431
9.3 Metal-Mesh Slings: Selection, Contact and Removal
Key Takeaways Explain This Topic AI
Do not concentrate demand into a few mesh elements or distort a handle.
Coated mesh can have a lower permitted temperature range than uncoated mesh.
New and repaired mesh assemblies require the specified controlled proof test.
Last updated: October 2026
Recognize fabric and handles
A metal-mesh sling uses linked or woven metallic elements forming a flexible fabric attached to handles. Its width spreads contact over a larger area than a narrow rope, and its metallic construction can suit particular abrasive or cutting environments. It remains a rated sling with specific bend, handle, temperature and use limitations.
The fabric and handles form one assembly. A handle must transfer force into the fabric and seat properly in the hoist connection. Substituting an improvised handle or connector can change both strength and geometry. Identification must state the rated capacity for the relevant vertical, basket or choker use as required by the applicable standard.
Metal mesh is not interchangeable with chain, wire rope or textile merely because it is flexible. Its surface may mark a finished load, and a coating can change temperature and chemical limits. Select it for the actual material and contact conditions, using the manufacturer’s instructions.
Support the load across the fabric
Arrange the sling so the load is supported appropriately across its width. Avoid concentrating the entire demand on a few strands, cross rods or an edge of the handle. A wide nominal fabric does not provide its full rated behavior if folded, bunched or loaded unevenly.
In a basket hitch, balance and retention still matter. Two fabric portions supply support, but the actual angle, bend and load geometry determine the permitted rating. In a choker hitch, the designed handle arrangement must pass and tighten as instructed without distortion. Do not improvise a choke with an ordinary ring that bends the handle or pinches the fabric.
- Selection question Application consequence
- Is the fabric width supported appropriately? Prevents localized concentration
- Do handles seat without binding? Preserves the intended force path
- Is the hitch approved? Establishes applicable capacity
- Is the surface suitable? Controls slipping and load damage
- Is the coating compatible? Avoids applying bare-metal limits to a coated product
- Understand temperature distinctions
OSHA 1910.184 provides an operating range for uncoated metal-mesh slings of −20°F through 550°F without reducing WLL. It gives a different range for slings impregnated with polyvinyl chloride or neoprene: 0°F through 200°F . For service outside those ranges or other impregnation materials, follow manufacturer recommendations.
These provisions do not approve every complete assembly for every exposure within the numbers. Apply any stricter manufacturer conditions and evaluate the load’s surface, fittings and coating. The distinction is particularly important when a protective covering makes a metal sling appear suitable for hot work despite having a lower permitted range.
Inspect fabric and handles
Under OSHA 1910.184, removal criteria include broken welds or brazed joints along a sling edge; specified wire-diameter reduction from abrasion or corrosion; lack of fabric flexibility; specified handle distortion; and cracked or distorted handles. The regulation distinguishes 25% wire reduction from abrasion and 15% from corrosion . Do not use a generic wire-rope broken-wire count for mesh fabric.
The handle’s openings and cross-sectional dimensions also have stated criteria. Identify the original dimensions and applicable rules before evaluating wear. Any cracked handle or distorted attachment requires removal under the applicable condition, even if the fabric still looks broad and intact.
A loss of flexibility can indicate damage or contamination that changes how the sling distributes force. Do not force stiff fabric into position with a hammer. Remove suspect equipment for authorized assessment. Field welding of broken mesh is not a repair method.
Testing and repair
OSHA requires new and repaired metal-mesh slings, including handles, to be proof tested by the manufacturer or equivalent entity at a minimum of 1.5 times rated capacity before use. Elastomer-impregnated slings are proof tested before coating. This is a controlled requirement with identification and records, not permission to overload a sling during an ordinary pick.
Repairs must be performed by the manufacturer or an equivalent entity under the regulation. The repair information and proof-test record establish traceability. A rigger discovering a broken edge weld should remove the assembly from service rather than reduce its capacity by an invented percentage.
Selection example
A supplied mesh sling is rated 8,000 lb in the applicable basket arrangement. The proposed load is 7,000 lb, but its narrow raised ridge concentrates contact into a small part of the fabric. The arithmetic comparison alone is insufficient. Obtain an approved contact arrangement or a different suitable sling. The same issue would remain if a wider fabric were selected without ensuring actual distributed support.
After the lift, release the sling only when the load is stable. Do not drag mesh from beneath a fully weighted object, allow a handle to drop uncontrolled, or fold it sharply for storage. Store it in the approved way so the fabric remains flexible, the handles undamaged and identification readable.
Sources: OSHA metal-mesh sling provisions , CCO reference manual .