Study guide
6.1 Determine Equipment Requirements and Compatibility
NCCCO Rigger Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Certification and Exam Preparation
1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification
2 Identify and Measure the Load
2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling
3 Center of Gravity and Support Geometry
3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access
4 Route and Site Hazards
4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions
5 Team Duties and Communications
5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication
6 Equipment Requirements and Lift Planning
6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies
7 Balanced Sling Forces
7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand
8 Composite and Unequal Loads
8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing
9 Wire Rope, Chain and Metal Mesh Slings
9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal
10 Synthetic Rope, Web and Roundslings
10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers
11 Hitch Application and Sling Protection
11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection
12 Shackles, Hooks and Collector Hardware
12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels
13 Threaded Points and Adjustable Hardware
13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems
14 Compression Hardware and Rigging Blocks
14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving
15 Manual, Lever and Powered Hoists
15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls
16 Jacks, Rollers and Portable Supports
16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility
17 Structural Lifters and Clamps
17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters
18 Mechanical, Vacuum and Magnetic Devices
18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples
19 Inspection, Removal and Records
19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing
20 Lift Control, Rotation and Completion
20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment
21 Technical Standards and Crane Capacity
21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431
6.1 Determine Equipment Requirements and Compatibility
Key Takeaways Explain This Topic AI
WLL applies only under its specified conditions.
A design factor is not available overload capacity.
Equipment substitutes require capacity and compatibility checks.
Last updated: October 2026
Specify the operation before the equipment
Equipment requirements come from the load, movement, environment and destination. Begin with verified weight and geometry, approved attachment points, required orientation, available headroom and the complete route. These inputs determine whether the operation needs a crane, hoist, beam, sling arrangement, rollers or another handling system.
Choosing the largest available machine first can hide compatibility problems. A crane may have ample capacity but insufficient hook height for the selected bridle. A chain fall may fit the headroom but have insufficient travel. A machinery skate may carry its calculated reaction yet be unsuitable for a rough surface or an uncontrolled slope. The system must complete the movement, hold the load when required, and permit safe landing and removal.
Working load limit (WLL) is an allowable load for specified conditions. Its use requires identifying the rated configuration, direction, hitch and relevant limitations. A catalog breaking strength is not a WLL. A design factor is built into the rated product and is not spare field capacity that may be consumed by an overload.
Identify the controlling element
Trace the force path and determine the demand on each item. Lower slings can carry inclined tension greater than their vertical load share. A collector link can carry the combined system load. A redirect block anchor can carry the vector sum of two rope forces. The supporting beam may carry a hoist’s suspended load plus equipment deadweight and relevant movement effects.
Requirement Selection question
Capacity What force reaches this item in this configuration?
Geometry Does it fit, seat and align without binding?
Travel Can it move through the required distance and orientation?
Control Can motion and holding be controlled by the planned method?
Environment Are temperature, chemicals and site conditions permitted?
Removal Can the gear be released after stable placement?
The controlling limit may be different at different stages. A beam can be limited by a specific adjustable span, a hoist by line pull or duty, and a sling by its hitch rating. Do not add unrelated component capacities and call the sum the system capacity. Each component must satisfy its own demand within the approved arrangement.
Match lifting characteristics to the load
Wire rope, alloy chain, webbing, roundslings, synthetic rope and metal mesh have different contact behavior and limitations. Flexible slings can conform to shapes but may require bend control and edge protection. Chain offers adjustable assembly options when supplied for overhead lifting, but it can mark surfaces and should not be twisted or improvised with mismatched fittings. Metal mesh spreads contact over width but still needs suitable handle geometry and support.
A lifting beam and spreader solve different geometry problems. A beam can reduce upper headroom, while a spreader’s top bridle usually requires more height. Their self-weight and permitted spans differ. Selecting one may change both crane capacity accounting and sling forces. Make the choice from the manufacturer’s rated configuration rather than the generic device name.
For powered devices, identify the supply and control needs. An air hoist needs suitable air pressure and flow at the hoist, an electric hoist needs the specified supply and duty conditions, and a vacuum lifter needs compatible surfaces and functioning vacuum indication. Availability of a hose or power outlet does not establish the required operating conditions.
Consider assembly and reach
Workers need safe access to install connections. A high attachment point may require a separate approved access method. The rigging must have enough reach without violating angle or hitch conditions. Account for fitting dimensions rather than treating a sling’s nominal length as the complete connection distance.
A plan also needs enough controlled lowering range. A chain fall that can raise a component into place may run out of available chain before returning it to a safe support. A jack’s rated stroke and required starting clearance both matter. Avoid reaching an equipment limit with the only escape being an improvised transfer to another device.
Selection scenario
An 18,000-lb machine must enter a low-ceiling bay while remaining upright. Direct slings meeting at a high hook create adequate angles but exceed the headroom. Flattening them reduces height and increases tension; it may also increase inward force on the machine. An approved low-headroom lifting beam with suitable vertical lower connections may solve the geometry, but its added weight and span rating must be checked. The solution changes the system, not just one number.
Record the selected configuration
List the actual equipment identifiers, ratings, applicable hitches, spans, angles and instructions needed for use. “Two large slings” does not establish a verifiable selection. An equally rated substitute may have a different eye size, material or bend limit. Any substitution requires checking the affected compatibility conditions.
Before execution, compare the assembled system to the plan. Confirm that the intended components are present, required inspections are current and operator instructions are available. If the field arrangement differs, resolve the change through the plan’s authority before taking load. This closes the loop from calculated requirements to the equipment actually carrying the force.
Sources: CCO Level II planning and selection outline , CCO reference materials .