Study guide

14.3 Rigging Blocks, Resultants and Reeving

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

14.3 Rigging Blocks, Resultants and Reeving

Key Takeaways Explain This Topic AI

Equal parallel rope forces can impose twice line pull on a block attachment.

A redirect alone does not necessarily add mechanical advantage.

Fleet-angle limits are equipment and rope specific.

Last updated: October 2026

Line pull is not always block load

A rigging block supports rope over a sheave. A snatch block can open to admit the rope without passing its end through the block. Blocks may redirect a line or form part of a mechanical-advantage system. The block body, sheave, attachment and anchor each need suitable rating and geometry.

Two rope forces act on a redirect block. Their vector sum determines the resultant at the block attachment, with block weight and other relevant effects also accounted for. In a simple static model with equal tension P in both legs, and included angle θ between the two forces pulling away from the block: F = 2 P cos ⁡ ( θ / 2 ) F=2P\cos(\theta/2) F = 2 P cos ( θ /2 )

The angle definition matters. When both legs leave in nearly the same direction, θ is near zero and the resultant is nearly twice line pull. When the legs form a right angle, the resultant is approximately 1.4142 times line pull. Do not use the rope’s change-of-direction angle without translating it into the angle between the force vectors.

Work a redirect example

A block redirects a line with assumed equal 8,000-lb tension through a 90-degree included force angle. The ideal rope-force resultant is approximately 11,314 lb . The anchor shackle, sling and supporting structure must be checked for that demand and applicable direction, along with relevant additional effects. Selecting them for only 8,000 lb would omit the second force.

  • Included force angle Ideal factor for equal tension
  • 0° 2.0000
  • 60° 1.7321
  • 90° 1.4142
  • 120° 1.0000
  • 180° 0.0000 rope-force resultant

The ideal zero at 180 degrees does not mean the installed block carries no weight or needs no attachment capacity. The rope forces cancel only in the defined ideal direction. Block self-weight, unequal tension, friction and actual geometry still matter. Real installations must follow rated product and equipment instructions.

Distinguish line and block ratings

Some product data describe allowable line pull, while other data describe total block load. Read the manufacturer’s definition. A label of “10 tons” cannot be interpreted without knowing what the rating covers. The anchor connection also has its own rating and permitted direction.

Check sheave diameter, groove size, rope compatibility, guards, side-plate closure, pins and retention. A sheave that accepts the rope physically may still provide an unsuitable bend radius or groove. Do not side load the block or let the rope leave the groove under an unapproved fleet angle.

Mechanical advantage is idealized

A multiple-part reeving system can reduce input line pull by distributing the supported load over several effective rope parts. In an ideal model, required line tension is the supported force divided by the number of supporting parts. Actual friction and equipment limits change the required input and permitted use.

Count parts supporting the moving block, not every visible rope segment anywhere in the system. A redirect added to the fixed lead may change direction without adding mechanical advantage. Include the moving block and carried equipment weight in the supported inventory where relevant.

A training 12,000-lb load with four ideal supporting parts has 3,000-lb tension per part. This does not establish real winch demand without friction and system data. It also does not rate the fixed anchors; their resultants depend on the attached rope directions and tensions.

Fleet angle and rope travel

Fleet angle describes lateral departure of rope between a sheave and drum relative to the intended drum alignment. Excessive angle can cause rubbing, poor spooling or groove departure. Limits depend on rope, drum and equipment design. Do not impose a universal 1.5-degree smooth-drum or 2-degree grooved-drum limit on every system without manufacturer support.

Follow the equipment’s permitted reeving and rope-path arrangement. Check that the rope cannot foul adjacent structures, rub against an edge or strike the termination. Keeping the payload clear does not establish a clear rope path.

Anchor-review scenario

A crew anchors a redirect block with a shackle whose WLL equals line pull. Both rope legs run nearly parallel toward the load and winch. The actual resultant approaches twice line pull, so the selection may be insufficient. Recalculate the vector demand and verify the supporting structure before tensioning.

During operation, stop for rope derailment, side-plate movement, binding or abnormal sounds. Never reach into a moving block or guide a tensioned rope by hand. After use, inspect sheaves, bearings, guards and retaining parts as instructed, and keep the complete assembly identifiable for future selection.

Compare supporting parts with a fixed redirect

Suppose a moving block has two effective vertical supporting rope parts and carries a total 6,000-lb ideal load. Each part carries 3,000 lb. Adding a fixed redirect to route the hauling end toward the operator does not create a third supporting part at the moving block; its ideal load share remains two parts.

The fixed redirect's anchor still requires a separate resultant calculation. If its equal-tension rope legs form a 90-degree included force angle, the ideal resultant is 3,000 × 1.4142, approximately 4,243 lb, before applicable additional effects. Counting three parts and selecting that anchor for only 2,000 lb would make both errors at once.

Sources: CCO block capacity and reference booklet , Crosby block application information .