Study guide

17.3 Beam Clamps as Attachments and Beam/Girder Lifters

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

17.3 Beam Clamps as Attachments and Beam/Girder Lifters

Key Takeaways Explain This Topic AI

A suspension clamp is not automatically a beam lifter.

Clamp WLL does not approve the supporting beam.

Include relevant hoist weight and block resultants in attachment demand.

Last updated: October 2026

Two different applications share similar names

A beam clamp used as an attachment point grips a suitable supporting beam and provides suspension for a hoist or rigging connection. A beam or girder lifting clamp grips the member being lifted. The CCO blueprint identifies both uses. Do not assume a device designed to hang from a stationary beam can also lift that beam as a payload.

The product must state its intended application and permitted load direction. Attachment clamps often have flange-width and thickness ranges, mounting procedures and restrictions on side loading. Payload lifters can have different grip, orientation and minimum-load conditions. Identify the exact mechanism and instructions before selecting the device.

A clamp’s WLL does not establish the supporting beam’s capacity. The beam, its connections and supporting structure must accept the applied reaction. The force may be concentrated at one location and can include hoist weight and movement effects. An ordinary overhead member is not automatically an approved lifting anchor.

Fit the actual flange

Measure width, thickness, profile and any taper or obstruction relevant to the product. A jaw that spans the flange can still seat incorrectly because the flange is outside its thickness range or has an incompatible profile. Use the manufacturer’s adjustment and locking method with the correct parts.

  • Application Primary checks
  • Suspension attachment Supporting beam capacity, flange fit and permitted reaction direction
  • Payload beam lifter Member grip, orientation, actual share and retention
  • Trolley clamp Wheel/flange compatibility and permitted travel
  • Girder clamp in a pair Manufacturer arrangement and unequal-share assessment

Do not tighten beyond the specified method to compensate for unsuitable fit. Do not insert arbitrary wedges, grind jaws or weld the clamp in place unless explicitly covered by an approved design. Those changes alter contact and can invalidate the rating.

Check force direction

A clamp approved for vertical suspension may not accept a horizontal pull from a lever hoist or redirect block. The resulting reaction can twist the clamp or bend the flange. Use the actual manufacturer’s side-load permission and the structure’s approved load path.

For a block attached to a clamp, the relevant demand can be the block resultant rather than only line pull. If equal rope tensions pull in nearly the same direction, attachment force approaches twice line tension in the ideal model. The clamp and supporting beam must be suitable for that direction and magnitude.

Attachment example

A hoist carries a 4,000-lb payload and weighs 300 lb. The stated total demand on its clamp is at least 4,300 lb before other relevant effects. A clamp rated 4,000 lb for total vertical load is insufficient under this inventory. A higher-rated clamp would still require verifying beam strength and flange compatibility.

Beam and girder lifting devices

When lifting a beam as cargo, select the dedicated product for its section shape, dimensions, weight and orientation. The member’s CG and possible rotation matter. A clamp at the wrong location can let a long member tilt or move out of its permitted grip.

Pairs of lifting clamps need the approved spacing and rigging geometry. Do not assume equal sharing if the CG is offset or the member deflects. Sling angles can apply additional inward forces or reduce clamp capacity. Some products use particular vertical suspension conditions; others permit a stated range.

A member’s flange may be too thin, damaged or locally weak for the proposed grip even when total beam strength is high. The payload must remain retained through lift-off, travel and landing. Surface coatings, oil, scale and wear can affect grip mechanisms.

Inspect locks and contact surfaces

Check identification, body, jaws, spindle or adjustment parts, pins, suspension points and locking mechanisms. Follow the manufacturer’s wear and removal criteria. Missing parts, cracks, deformation or an inability to seat and lock properly require stopping use and authorized assessment.

A clamp installed for a previous lift must be checked for the new position and demand. It may have moved, loosened or been used outside its intended direction. Do not rely solely on the fact that it remains attached overhead.

Install, use and release deliberately

Use a safe access method for overhead installation. The installer must not balance on the load or an unapproved ladder arrangement while handling a heavy clamp. Confirm the clamp is seated and secured before connecting the hoist or taking weight.

During the planned trial lift, observe alignment and any slipping or flange movement from a safe location. Stop for unexpected behavior. A visible shift is not something to cure by reaching up and tightening the loaded device.

For payload clamps, land the member on stable supports and unload before release. For attachment clamps, unload and follow the removal procedure, controlling the clamp’s own weight. Keep products identified by application in storage so a suspension anchor is never mistaken for a cargo-lifting clamp.

Sources: CCO beam-clamp selection and execution topics , CMCO beam and trolley clamps , equipment catalog .