Study guide

17.2 Plate Clamps, Material Limits and Grip Conditions

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

17.2 Plate Clamps, Material Limits and Grip Conditions

Key Takeaways Explain This Topic AI

Use the clamp intended for the required lifting or turning orientation.

A single-plate clamp does not automatically retain a stack.

Apply any product-specific minimum load as well as maximum capacity.

Last updated: October 2026

Select the intended clamp function

A plate clamp grips specified material through a cam, jaw, friction surface or other designed mechanism. Vertical lifting, horizontal handling and turning clamps have different permitted functions. A clamp rated for one orientation is not automatically approved for another or for a stack of plates.

Identify the product’s load capacity, jaw-opening range, material thickness, hardness, surface condition, minimum load if any, and permitted sling direction. Some products require a minimum load to develop their intended grip. Others use different mechanisms. Do not apply one manufacturer’s 10% minimum to every plate clamp.

The plate itself must be suitable for the clamp. A thin, brittle, coated, hardened or flexible plate can interact differently with teeth or friction pads. The clamp’s nominal WLL does not prove that the material will remain secure. Use the product’s approved material and surface conditions.

Fit and engage completely

Place the plate within the specified jaw range and seating depth. Engage the latch or locking mechanism as instructed. A jaw that partly closes on a thick edge is not an approved fit. A locking lever that appears closed may still leave the cam incompletely engaged.

Check that the load direction remains within the clamp’s permitted range. Inclined slings can reduce allowed capacity or create twisting at the grip. Read the actual angle table rather than applying a shackle or eyebolt reduction. A pivoting attachment can help alignment only within its designed conditions.

  • Clamp input Why it controls use
  • Jaw range Establishes fit to the actual thickness
  • Material/hardness Determines whether the grip mechanism works as intended
  • Surface Oil, scale, coating or contamination can impair engagement
  • Orientation Selects vertical, horizontal or turning permission
  • Minimum load May be required for a particular grip design
  • Sling direction Can change allowable capacity or alignment

A clamp intended for a single plate must not be assumed to retain a stack. The upper plate may be gripped while lower pieces remain unrestrained. The correct stack-handling device and procedure must establish retention of all pieces.

Calculate the actual clamp demand

When multiple clamps support a plate, CG and support geometry determine sharing. Equal clamp sizes do not establish equal forces. A flexible plate can deflect, and a changed sling angle can create different reactions. Use the manufacturer’s required arrangement and approved plan.

A training pair of clamps each rated 4,000 lb does not automatically lift an 8,000-lb eccentric plate. If the actual reactions are 5,000 and 3,000 lb, the first clamp exceeds its rating. If sling direction reduces either rating, that lower value must also be applied.

Surface condition and grip

Teethed clamps may mark the material; nonmarring clamps can rely on different contact and surface conditions. Choosing a smooth-pad clamp to protect a finish does not approve use on an oily surface. The product’s grip requirements remain controlling.

Clean or prepare the load only through the appropriate approved method. Do not grind the plate randomly or alter teeth to make a clamp fit. Damage, wear or contamination can reduce grip without changing the clamp’s visible overall size.

Minimum-load example

Assume a particular clamp’s instructions specify a 2,000-lb WLL and a minimum load of 10% of WLL. A 100-lb plate does not meet the stated 200-lb minimum even though it is far below maximum capacity. The numerical maximum alone would lead to the wrong selection. These supplied conditions are product specific.

Turning permission must be explicit

A clamp that securely holds a vertical plate may not be rated to turn it from horizontal or rotate through an arbitrary angle. During turning, the load direction relative to the jaw changes and the attachment may pivot or bind. Use a product expressly approved for the required maneuver with its prescribed arrangement.

A trial lift can verify initial engagement and attitude but cannot override an unapproved material or orientation. Keep personnel clear and never reach toward the jaw to correct it while loaded. Stop, land securely and unload before any ordinary repositioning.

Inspect and release safely

Inspect jaw surfaces, cams or teeth, pins, locking mechanisms, body, suspension points and identification. Follow wear gauges and removal criteria for the product. A clamp with worn teeth is not repaired by sharpening them arbitrarily. Required replacement parts and repairs must use the authorized process.

Land the plate on approved stable supports before releasing the clamp. A vertical plate can tip when grip is removed unless braced or restrained. Confirm that the supported condition is safe and that release controls can be reached without placing hands in a pinch zone.

After use, clean and store as instructed, preserving grip surfaces and identification. Keep rejected clamps separate from serviceable ones. The exam decision is a product-specific grip assessment as well as a capacity calculation.

Sources: CCO plate-clamp topic , CMCO clamp catalog and instructions .