Study guide

21.2 Crane Charts, Suspended Weight and Capacity Deductions

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

21.2 Crane Charts, Suspended Weight and Capacity Deductions

Key Takeaways Explain This Topic AI

Boom length is not load radius.

Count the applicable payload, rigging, device and crane accessories once.

The pick chart does not authorize a lower-capacity destination stage.

Last updated: October 2026

The correct chart comes before arithmetic

A crane load chart states capacity for a specific crane configuration and operating condition. Determine the actual model, boom/jib arrangement, counterweight, outrigger or crawler configuration, operating area and radius. A capacity printed elsewhere in the chart does not apply merely because it is large enough.

Load radius is generally the horizontal distance from the crane's axis of rotation to the load's vertical line of action, interpreted according to the chart. Boom length is not radius. Deflection under load can change radius, so the operator must use the correct loaded geometry and chart instructions.

The rigger supplies reliable load weight, approximate CG, pick and set positions, rigging arrangement and relevant device weights. The operator verifies the crane's capacity and permissible operation. These responsibilities complement each other. A Level II rigger must understand the calculation without pretending to qualify as the operator of every crane type.

Inventory every applicable weight

The crane may support payload, slings, shackles, lifting beam, hoists, hook block or ball, load line and other items identified by the chart. Some charts express gross capacity and require deductions; others define entries differently. Read the chart's notes so each item is counted once and the same accounting basis is used in the comparison.

  • Item Capacity question
  • Payload Reliable weight, including contents and attached parts
  • Slings/hardware Weight carried in the applicable suspension
  • Beam or other device Self-weight as well as approved load rating
  • Hook/block/ball Applicable chart deduction or inclusion
  • Load line and accessories Chart-specific treatment and configuration

Do not omit a device because it has its own WLL. Do not deduct a block from net capacity and then add the same block again to demand. An arithmetic result is only meaningful when its inventory and capacity definitions match.

Gross-capacity example

Assume a supplied chart gives 24,000 lb gross capacity at the governing radius. Its instructions require deduction of a 900-lb hook block, 500-lb lifting beam, 200-lb slings/hardware and 100-lb applicable load-line allowance. These stated example values are not universal equipment weights. Net payload capacity = 24,000 − ( 900 + 500 + 200 + 100 ) = 22,300 lb \text{Net payload capacity}=24{,}000-(900+500+200+100)=22{,}300\text{ lb} Net payload capacity = 24 , 000 − ( 900 + 500 + 200 + 100 ) = 22 , 300 lb

A 21,000-lb payload is below the resulting 22,300-lb payload limit. Equivalently, total demand is 22,700 lb compared with 24,000 lb gross. The gross-basis utilization is 22,700 / 24,000 ≈ 94.6 % 22{,}700/24{,}000\approx94.6\% 22 , 700/24 , 000 ≈ 94.6% . The comparison still does not approve weather, ground, structural attachments, operating sector or an employer's lower utilization limit.

Find the governing stage

Check the full pick-to-set route. Capacity can decrease at a greater radius or in a different operating sector. A load safely picked close to the crane may exceed the chart during placement. The limiting stage may also occur while transferring support between cranes or moving a rotating load.

Use only chart interpolation or rounding methods expressly permitted. If a radius falls between entries, do not create a higher interpolated capacity unless allowed. Follow the maker's specified next-entry or other procedure. Likewise, do not apply a fully extended-outrigger chart to a partially extended setup without its approved chart.

Changed-radius example

The same load has 22,700 lb gross demand. At the final radius the applicable supplied chart permits only 21,500 lb gross. Initial pick capacity does not authorize this destination. Change the setup, crane, load or route through an approved revised plan, then repeat checks. A stronger sling cannot increase the crane's chart capacity.

Understand what utilization does not mean

A project may define a critical lift at a particular utilization percentage. Other triggers can include personnel hoisting, multiple cranes, unusual consequences or proximity to occupied facilities. There is no single federal percentage that universally defines all critical lifts, and a critical-lift designation does not replace capacity verification.

OSHA 1926.1417 requires operation within rated capacity and reliable weight verification. Its provisions permit specific alternatives for verifying load weight; they do not mean any uncertain load can be lifted until an overload alarm sounds. The operator must follow the applicable procedure, including the conditions on using load-weighing indications.

A crane's rated-capacity limiter, anti-two-block device or load indicator provides a particular function. Such aids do not replace chart understanding, required equipment checks or the rigger's load information. An absence of alarm is not proof of safe lifting points, approved sling geometry or suitable ground.

Additional limits remain separate

Ground support and level condition affect the crane's stability. Wind can affect a large sail-area load even below a weight limit. Side pulling or dragging can introduce forces outside chart assumptions. Follow manufacturer limits and the approved plan rather than reducing a number by an arbitrary percentage to compensate.

For personnel hoisting, OSHA applies a specific 50% criterion to the total defined load, except proof testing. Do not use ordinary payload capacity as the sole personnel-hoisting calculation. Multiple-crane operations need each crane's own load inventory, reaction and changing radius; a universal tandem derating does not substitute for those checks.

Source: CCO B30.5 reference and responsibilities , OSHA crane operation , OSHA ground conditions .