Study guide
10.3 Roundslings, Core Protection and Performance Fibers
NCCCO Rigger Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Certification and Exam Preparation
1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification
2 Identify and Measure the Load
2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling
3 Center of Gravity and Support Geometry
3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access
4 Route and Site Hazards
4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions
5 Team Duties and Communications
5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication
6 Equipment Requirements and Lift Planning
6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies
7 Balanced Sling Forces
7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand
8 Composite and Unequal Loads
8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing
9 Wire Rope, Chain and Metal Mesh Slings
9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal
10 Synthetic Rope, Web and Roundslings
10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers
11 Hitch Application and Sling Protection
11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection
12 Shackles, Hooks and Collector Hardware
12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels
13 Threaded Points and Adjustable Hardware
13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems
14 Compression Hardware and Rigging Blocks
14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving
15 Manual, Lever and Powered Hoists
15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls
16 Jacks, Rollers and Portable Supports
16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility
17 Structural Lifters and Clamps
17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters
18 Mechanical, Vacuum and Magnetic Devices
18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples
19 Inspection, Removal and Records
19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing
20 Lift Control, Rotation and Completion
20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment
21 Technical Standards and Crane Capacity
21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431
10.3 Roundslings, Core Protection and Performance Fibers
Key Takeaways Explain This Topic AI
Read the tag; cover color is not a universal U.S. WLL code.
The ordinary cover is not a rated cut protector.
A damaged or exposed core requires removal under the applicable criteria.
Last updated: October 2026
Distinguish the core from its cover
A roundsling contains continuous load-bearing fibers enclosed by a protective cover. For an ordinary polyester roundsling, the core carries the rated tensile load and the cover protects it. A cover that still looks present does not prove the internal fibers are sound, and a damaged cover can expose the core to cutting or contamination.
Roundslings can be flexible and light for their capacity, allowing contact around some irregular shapes. They still require correct bends, compatible hardware and suitable protection. The cover can bunch, and concentrated contact can damage core fibers. Do not treat softness as evidence that all contact conditions are permitted.
Identify the product material and rated assembly. Polyester and high-performance fiber roundslings can have different heat, chemical, bend and inspection requirements. High-modulus polyethylene, aramid and other fibers are not interchangeable. Use the actual manufacturer’s instructions rather than combining properties from several materials into one imaginary product.
Read tags rather than colors
Color coding is used by some manufacturers or standards, but it is not a universal U.S. capacity system. A purple, green or yellow cover does not establish a particular rating unless the relevant product identification and standard support it. The legible tag and documentation establish WLL, material and applicable hitches.
- Identification item What it establishes
- Manufacturer and product Which instructions apply
- Material Applicable exposure and mechanical limitations
- Rated hitch values Capacity for the described arrangement
- Size or other assembly designation Traceable product selection
- Inspection features Which product-specific indicators to evaluate
A missing or unreadable required tag requires removal from service under the applicable sling requirements. Field guessing based on cover color or diameter is not retagging. Authorized identification restoration requires traceable information and the manufacturer or other permitted process; proof testing is not automatically required in every retagging situation, nor does a test alone reveal an unknown fiber.
Use the correct contact geometry
Check the minimum bearing dimensions, bend requirements and hardware fit specified for the sling. A high-capacity roundsling in a small shackle may not have enough bearing width or room to seat. Stacking several textile slings in one hook can create crowding, crossed load paths or contact with the latch.
Use approved connectors or a suitable collector arrangement when necessary. A fitting’s steel capacity does not establish textile compatibility. Manufacturer instructions may address permitted overlap or folding; the Level II practical course’s overlap scoring treatment is not a universal field installation rule.
For choker and basket use, apply the actual hitch rating and angle conditions. A nominal basket value can assume specified bends and orientation. If a table already includes a sling angle, do not apply the same angle reduction twice. If the lower parts are inclined, calculate or look up the applicable condition rather than assuming both remain vertical.
Protection is more than a sleeve
The ordinary roundsling cover is not a rated cut protector. Add protection selected for the actual edge, force and movement. An abrasion sleeve may protect against rubbing but not a severe edge under load. Ensure protectors remain in position throughout any rotation or sliding contact.
An internal inspection or telltale feature is product specific. Some products have indicators for certain damage modes; others do not. An unchanged indicator does not prove the entire core is undamaged by every exposure. Follow the inspection criteria for the actual product, including any limitations on using the indicator.
Remove suspect equipment
Inspect for cover cuts or tears, exposed core, knots, heat damage, chemical damage, unusual stiffness, lumps, uneven core distribution or damaged fittings as specified. For ordinary polyester roundslings, exposed or damaged core fibers are a removal condition. The manufacturer determines whether a particular cover repair is permitted; field core repair is not an acceptable method.
Do not assume a numerical percentage of visible cover damage measures remaining strength. The load-bearing material is internal and damage may be localized. Remove the sling and keep it separated pending authorized disposition. Cutting or destroying rejected gear can be appropriate under the disposal process, but evaluation and authorized repair should not be confused with automatic destruction of every removed item.
Application scenario
A roundsling with a readable 20,000-lb applicable rating is proposed for a 15,000-lb leg tension. During inspection, the cover has a cut exposing core fibers. The capacity comparison cannot override the removal criterion. Replacing it with another approved sound sling also requires verifying the same material, hitch and bearing compatibility.
When storing, avoid hooks, edges or surfaces that can cut the cover; protect from harmful exposure and keep identification visible. Handle high-capacity slings with suitable care even when they are light enough to carry easily. Their portability does not make hidden core damage less consequential.
Sources: CCO sling reference materials , CMCO rigging resources .