Study guide

10.1 Synthetic-Rope Slings and Approved Splices

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

10.1 Synthetic-Rope Slings and Approved Splices

Key Takeaways Explain This Topic AI

Select a rated lifting assembly rather than ordinary rope by appearance.

Use the splice procedure for the actual construction.

Breaking strength is not a field-authorized WLL.

Last updated: October 2026

A rope is not automatically a lifting sling

A synthetic-rope sling is a rated lifting assembly made from a specified fiber and rope construction with approved terminations. An ordinary tagline, towing rope or general-purpose rope does not become a lifting sling because it looks strong. Select a marked, documented assembly intended for the proposed lifting use.

Nylon, polyester, polypropylene and performance fibers have different behavior. Construction also matters: laid rope, single braid, double braid and other arrangements can have different splice and bending requirements. The rating belongs to the actual material, construction and termination. Fiber names alone do not establish WLL, temperature limits, chemical compatibility or electrical insulation.

Nylon can stretch more than polyester in many ordinary rope products, but a qualitative comparison is not a capacity or shock-load allowance. A more elastic sling can change geometry and allow movement; shock loading remains prohibited or restricted under the applicable rules and instructions. Performance fibers can have high strength for low weight while introducing particular heat, bend and inspection limitations.

Read identification and termination information

Determine diameter, material, construction, rated hitches and the approved splice or fitting. A splice transfers force through a defined arrangement of strands or braids. Its dimensions and fabrication procedure must match the product. Do not apply natural-fiber splice counts to every synthetic braid.

OSHA 1926.251 includes natural- and synthetic-fiber rope provisions, including prohibiting knots in place of splices and requiring appropriate splicing procedures for unlisted constructions. Its operating range for ordinary covered fiber-rope slings is −20°F through 180°F, with manufacturer recommendations for other stated conditions. Specific performance-fiber products need their own applicable instructions, not an assumption that every synthetic rope has identical limits.

  • Sling feature Selection consequence
  • Fiber Determines exposure compatibility and mechanical behavior
  • Construction Determines splice, bend and inspection instructions
  • Termination Must be rated and compatible with the connection
  • Hitch and angle Selects the applicable capacity condition
  • Contact surface Can require bend control and cut protection
  • Do not create capacity from breaking strength

A catalog minimum breaking strength is not the allowable force for a field-made assembly. Fabrication, termination efficiency, design factor and service conditions must be addressed in the rated product. Dividing any rope’s breaking strength by an arbitrary factor does not authorize a rigger to make and use an unapproved sling.

A given rated rope sling with 6,000-lb applicable leg WLL can be checked against a calculated 5,000-lb static tension. That comparison remains incomplete until hitch, bends, exposure and load attachments are suitable. If the only available rope has an 18,000-lb breaking-strength label but no lifting assembly rating, it cannot be treated as an equivalent 6,000-lb sling by choosing a convenient divisor.

Control contact and movement

Synthetic rope can be damaged by cutting, abrasion, heat and contamination. Provide protection designed for the actual contact force and edge, preserving the manufacturer’s minimum bend requirements. A cloth sleeve may protect against abrasion without protecting against a sharp edge under high tension. Select protection according to its documented function.

Keep rope away from moving drums, gears and other equipment that could entangle it. Do not drag it over rough surfaces or pull it from beneath a supported load. A sling should follow the planned load path and remain seated throughout any turn or tilt. Changing contact as the load rotates can move protection away from the controlling edge.

A choker or basket must use its approved configuration. Do not knot the body to shorten it or join two slings by an improvised knot. A termination sized to pass through a handle may still be unsuitable when the choke bears against the splice. Use the manufacturer’s hitch instructions.

Inspect the actual construction

Look for abnormal wear, powdered fibers between strands, cuts, broken fibers, distortion, discoloration, heat damage, chemical effects and damaged fittings. Internal damage may differ from surface fuzz. Follow the manufacturer’s opening and inspection method where required rather than forcibly separating a braid with a sharp tool.

Removal and evaluation must account for material and construction. Generic rules such as “discard only after half the fibers are cut” are unsafe. Missing identification, uncertain exposure or evidence of damage requires the applicable removal/evaluation process. Never assume an absence of a colored warning yarn proves soundness; such indicators are product specific.

Compatibility example

The plan specifies a rated double-braid polyester sling with an approved eye splice and protection for a known edge. A crew proposes substituting a same-diameter general-purpose nylon rope tied into an eye. The substitution changes material, termination, stretch, exposure and rating. It fails the assembly-identification and splice requirements before any capacity calculation can approve it.

Store rope slings clean, dry and protected from damaging heat, sunlight, chemicals and mechanical contact according to the manufacturer. Separate rejected gear from serviceable gear. The rope used for a tagline should remain a different identified item from the lifting sling so its function is never confused during setup.

Sources: OSHA fiber-rope provisions , CCO sling topics .