Study guide
10.2 Synthetic-Web Slings and Material Compatibility
NCCCO Rigger Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Certification and Exam Preparation
1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification
2 Identify and Measure the Load
2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling
3 Center of Gravity and Support Geometry
3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access
4 Route and Site Hazards
4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions
5 Team Duties and Communications
5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication
6 Equipment Requirements and Lift Planning
6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies
7 Balanced Sling Forces
7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand
8 Composite and Unequal Loads
8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing
9 Wire Rope, Chain and Metal Mesh Slings
9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal
10 Synthetic Rope, Web and Roundslings
10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers
11 Hitch Application and Sling Protection
11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection
12 Shackles, Hooks and Collector Hardware
12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels
13 Threaded Points and Adjustable Hardware
13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems
14 Compression Hardware and Rigging Blocks
14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving
15 Manual, Lever and Powered Hoists
15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls
16 Jacks, Rollers and Portable Supports
16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility
17 Structural Lifters and Clamps
17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters
18 Mechanical, Vacuum and Magnetic Devices
18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples
19 Inspection, Removal and Records
19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing
20 Lift Control, Rotation and Completion
20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment
21 Technical Standards and Crane Capacity
21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431
10.2 Synthetic-Web Slings and Material Compatibility
Key Takeaways Explain This Topic AI
Width alone does not identify web-sling capacity.
Use the correct vertical, choker or basket rating.
Nylon is prohibited where acids or phenolics are present under the cited rules.
Absence of warning yarns does not prove a damaged sling is sound.
Last updated: October 2026
Identify flat webbing and its rating
A synthetic-web sling uses woven flat material with sewn or fitted terminations. It may have eyes, endless construction or approved fittings. The assembly’s width, plies, material, stitching and configuration determine rating. Two equally wide slings need not have equal WLL.
Webbing can spread contact over a broad surface and suit loads that need lighter, flexible rigging. Those benefits do not establish cut resistance, chemical compatibility or permission to absorb shock. A wide sling can still be cut at an edge or concentrate force into a weak part of the payload.
Read the identification for material and rated hitches. Confirm that the eyes or fittings fit the selected hook, shackle or other connection without bunching or binding beyond permitted conditions. Follow the manufacturer’s eye-bearing and bend guidance. A large hardware rating does not approve webbing squeezed against a narrow bearing edge.
Select the appropriate hitch
A vertical leg carries its full applied tension. A choker uses the applicable choker rating and choke-angle conditions. A basket can provide two supporting portions but depends on balance, angle, bends and manufacturer conditions. Do not assume basket capacity is always twice vertical capacity in every geometry.
- Application condition Required check
- Straight leg Calculated leg tension against applicable rating
- Choker Choker capacity, choke angle and splice/contact location
- Basket Leg angle, load retention and bend conditions
- Edge contact Adequate retained protection for actual force
- Hardware eye Fit, bearing surface and permitted folding
A supplied web sling might be rated 5,000 lb vertical, 4,000 lb choker and 10,000 lb in its specified basket condition. Those given values cannot be interchanged. A 4,500-lb load exceeds the stated choker rating even though it fits the vertical rating. A basket used at a different angle needs its corresponding permitted rating.
Temperature and chemical limits
OSHA’s cited web-sling rules prohibit nylon and polyester web slings above 180°F . Polypropylene web slings have a 200°F restriction. These are operating restrictions, not melting points. A manufacturer may impose additional limits for the actual assembly, fittings or protection.
Nylon must not be used where acids or phenolics are present. Polyester and polypropylene must not be used where caustics are present, and aluminum fittings have a separate caustic prohibition. A statement that polyester resists some acids is not approval for any unknown acid concentration or temperature. Consult the manufacturer for actual exposure conditions.
Do not infer fiber type from color. Identification and documentation establish material. Discoloration, stiffness or a gummy texture can indicate damage, but an exposed sling may lose strength without an obvious visible change. Remove uncertain or damaged gear for appropriate assessment rather than assigning an invented reduction.
Protect against cutting and abrasion
Abrasion protection and cut protection have different purposes. An ordinary wear sleeve can reduce rubbing without preventing a loaded sharp edge from severing fibers. The protector needs suitability for the edge, contact force, sling and movement. Keep it retained through take-up, travel and rotation.
There is no universal edge-radius rule that makes every corner safe for every web sling. Thickness, load, contact pressure, movement and product design all matter. Follow the sling and protector manufacturer instructions. Cosmetic padding such as cardboard or an unapproved rag does not establish lifting protection.
Avoid pulling webbing over an edge under tension, crushing it between parts or letting it contact hot surfaces and weld spatter. Position it to avoid the load-bearing splice being subjected to unapproved bending or crushing. Keep hands clear while the webbing tightens.
Inspect stitching and fibers
Removal criteria include cuts, holes, tears, snags, broken or worn load-bearing stitching, acid or caustic burns, melting or charring, and damaged fittings under the applicable rules. Some manufacturers incorporate colored warning yarns, but not all do. Damage is not acceptable merely because no red yarn appears.
Knots must not be used to shorten or join slings. A knotted sling requires removal/evaluation under its instructions; untie-and-continue is not an authorized capacity restoration method. Likewise, sewing a patch in the field does not restore the engineered load-bearing splice.
Selection scenario
A nylon web sling has adequate choker capacity for a load, but the work area contains a known acid exposure. The numerical rating does not approve that environment. Select a compatible approved system after evaluating the actual chemical and conditions. Switching to an untagged polyester sling based on its color would leave the identification and compatibility gaps unresolved.
After use, inspect for new damage, preserve readable identification and store slings away from harmful sunlight, heat, moisture and chemicals as instructed. Keep removed gear physically separated so it cannot return to service through a mistaken selection.
Sources: OSHA web-sling requirements , CCO reference materials .