Study guide

Rigging Connections and Hardware Application

NCCCO Rigger Level I Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction and Exam Overview

About the CCO Rigger Level I Certification Official Level I Blueprint and Study Strategy

2 Chapter 2: Scope of the Rigging Activity

Load Path, Site Hazards, and Hazard Communication Verifying Load Characteristics and Attachment Points Special Handling and Unsafe Rigging Practices

3 Chapter 3: Technical Knowledge

Level I Standards: ASME and OSHA Hardware Ratings, Identification, and Compatibility Hoisting Personnel Under OSHA 1926.1431

4 Chapter 4: Rigging and Sling Inspection

Synthetic Web, Roundsling, and Fiber-Rope Inspection Wire-Rope Sling Inspection and Removal Alloy-Chain and Metal-Mesh Sling Inspection

5 Chapter 5: Rigging Hardware and Hook Inspection

Frequent Inspection of Rigging Hardware Hooks and Below-the-Hook Device Inspection

6 Chapter 6: Hitches, Sling Angles, and Sling Protection

Hitch Configurations and Tagged Capacities Sling-Angle Recognition and Capacity Tables Sling Protection and Bend Compatibility

7 Chapter 7: Rigging Connections, Knots, and Load Handling

Rigging Connections and Hardware Application The Five Practical Knots and Safe Tag-Line Use Landing, Securing, Disconnecting, and Stowing

8 Chapter 8: Practical Exam, Written Exam Strategy, and Final Review

Level I Practical Examination: Four Published Tasks Written Exam Final Review and Scenarios

Rigging Connections and Hardware Application

Key Takeaways Explain This Topic AI

Every connection must preserve the rated load path: components bear on intended surfaces, align with force, fit without binding, and retain their pins or closures.

Hook, shackle, eyebolt, swivel-ring, and turnbuckle limits are product-specific; avoid universal included-angle, side-load, thread-depth, or retention claims.

Personnel-platform hardware must meet OSHA 1926.1431 strength and positive-closing requirements, but the rule does not reduce every connection to one named shackle style.

Level I Execution also covers blocks, hoists, dollies, skates, rollers, A-frames, trolleys, compression hardware, beam clamps, softeners, and jacks.

Follow the supplied configuration and stop when the connection requires an unknown calculation, unauthorized modification, or hardware without a traceable rating.

Last updated: August 2026

  • Rigging Connections and Hardware Application
  • Preserve the intended load path

A connection is sound when force travels through each component's intended bearing surface without prying, tip loading, side loading, crushing, or opening. Before assembly, identify and inspect every part, verify its rating for the supplied force and direction, and check that mating sizes fit.

After assembly, trace the path from hoist hook to load. A latch should close freely; a pin should seat and retain; a sling eye should not bunch against an ear; a swivel should align; and no component should bear on threads or a sharp edge unless specifically designed for it.

Hooks and collector hardware

Seat the main connection in the hook bowl, not on the tip or latch. A latch retains slack gear and must not carry load. Multiple sling eyes must fit without crowding or forcing the latch open. When they do not, use the rated master link, subassembly, or collector hardware specified for the bridle.

Do not state that OSHA establishes a universal 90° included-angle rule for every pair of slings in every hook. Hook and sling manufacturers can limit included angle, number of components, and fit. Use their instructions and the assembly tag. A wide angle that pushes eyes up the hook sides is a clear stop condition even before a numeric limit is reached.

Shackles

Use the correct shackle type, original pin, and marked capacity. Arrange the pin and bow so each mating part bears as the manufacturer permits. Center point loads with approved spacers only when authorized. Side loading, multiple loads in the bow, and choker connections require the exact product guidance.

Avoid blanket claims that every pin-to-pin shackle connection is categorically prohibited by OSHA or that every shackle must be bow-to-bow. Evaluate whether the bearing surfaces and articulation are approved. The connection must not roll on threads, pry ears, bend pins, or rotate a screw pin loose.

Screw pins must fully engage. Bolt-type shackles provide positive retention where the application calls for it. OSHA personnel hoisting requires hooks and other detachable devices to close and lock and sets a five-times maximum-intended-load strength requirement for rigging hardware. A shackle used in place of a hook must be an alloy anchor type with a retained bolt or a screw pin secured against accidental removal. Verify the exact device and assembly.

Eyebolts and swivel hoist rings

Install eyebolts into suitable material with clean, compatible threads. A shoulder must seat as directed and the eye align with the force. Non-shouldered eyebolts are generally limited to in-line use. Angular ratings, thread engagement, washer use, and torque come from the exact product.

Swivel hoist rings must rotate and pivot freely before loading. Install the specified bolt, engagement, and torque. Make sure the bail is not trapped against the load. A swivel feature does not erase all angular restrictions.

Links, rings, swivels, and adjustable hardware

Master links and subassemblies collect sling legs and provide a compatible connection to the hook. Their openings must accommodate the legs without crowding, and their tag or marking must cover the number of legs and angle.

Turnbuckles and other adjustable hardware must be rated for lifting, correctly threaded at both ends, and secured against unintended rotation as instructed. Do not use unrated hook-ended tensioning hardware overhead. Never adjust an assembly while it is supporting a suspended load unless the system and procedure are explicitly designed for it.

Compression hardware and wedge systems depend on correct size, direction, seating, and retention. Use the specified rope, wedge, sleeve, or fitting combination. Do not mix parts based only on approximate diameter.

Blocks and hoists

A block changes rope direction or mechanical advantage. Verify its rating, attachment, sheave size, rope compatibility, reeving, guards, and alignment. Prevent side loading of side plates and keep rope seated in the groove.

Manual chain hoists and lever hoists must hang from approved supports, align hook to hook, and carry load on an untwisted load chain. Check brakes, latches, chain, hooks, controls, and travel. Never use the hand chain or lever extension to gain extra force, wrap load chain around the load unless designed for it, or pull sideways.

Material-moving devices

Dollies, skates, and rollers move supported loads horizontally. Verify individual and system capacity, surface condition, load distribution, travel path, and steering method. Secure against unexpected rolling and keep feet and hands clear.

A-frames and trolleys must be rated, stable, and compatible with the supporting track or structure. Stops, wheels, hangers, and attachments must function. The supporting structure's capacity must be approved; a rated trolley does not rate the beam.

Jacks require a firm base, adequate capacity, correct lifting point, and blocking as the load rises. Never rely on hydraulic pressure alone while working beneath a load. Lift in controlled increments and transfer support to approved blocking. Do not extend with makeshift handles.

Beam clamps must fit the flange and load in the direction allowed by the manufacturer. Do not side pull, attach to an unapproved member, or use a plate clamp as a beam clamp.

Softeners and connection protection

Place approved softeners where a load edge can damage a sling. Keep them from sliding as the connection seats. A softener does not correct an undersized pin, overloaded hitch, or improper attachment.

Final connection check

Before hoisting:

Match each component to the plan.

Verify WLL and loading direction.

Inspect identity, condition, and function.

Check pin, nut, cotter, latch, lock, or torque as applicable.

Confirm bearing, articulation, and edge protection.

Remove slack slowly and watch the assembly align.

Stop for binding, rotation, movement, or mismatch.

The CCO practical tests whether the finished connection matches each task card, including the specified plane. Field work follows the approved plan with the same precision.