Study guide

Hardware Ratings, Identification, and Compatibility

NCCCO Rigger Level I Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction and Exam Overview

About the CCO Rigger Level I Certification Official Level I Blueprint and Study Strategy

2 Chapter 2: Scope of the Rigging Activity

Load Path, Site Hazards, and Hazard Communication Verifying Load Characteristics and Attachment Points Special Handling and Unsafe Rigging Practices

3 Chapter 3: Technical Knowledge

Level I Standards: ASME and OSHA Hardware Ratings, Identification, and Compatibility Hoisting Personnel Under OSHA 1926.1431

4 Chapter 4: Rigging and Sling Inspection

Synthetic Web, Roundsling, and Fiber-Rope Inspection Wire-Rope Sling Inspection and Removal Alloy-Chain and Metal-Mesh Sling Inspection

5 Chapter 5: Rigging Hardware and Hook Inspection

Frequent Inspection of Rigging Hardware Hooks and Below-the-Hook Device Inspection

6 Chapter 6: Hitches, Sling Angles, and Sling Protection

Hitch Configurations and Tagged Capacities Sling-Angle Recognition and Capacity Tables Sling Protection and Bend Compatibility

7 Chapter 7: Rigging Connections, Knots, and Load Handling

Rigging Connections and Hardware Application The Five Practical Knots and Safe Tag-Line Use Landing, Securing, Disconnecting, and Stowing

8 Chapter 8: Practical Exam, Written Exam Strategy, and Final Review

Level I Practical Examination: Four Published Tasks Written Exam Final Review and Scenarios

Hardware Ratings, Identification, and Compatibility

Key Takeaways Explain This Topic AI

Use the marked working load limit for the exact product, configuration, direction, and environmental condition; never infer capacity from size or appearance.

Design factor, minimum breaking force, and proof-test load are not working load limits and do not authorize a higher operating load.

Compatibility includes fit, bearing area, articulation, material, pin diameter, thread engagement, and freedom from tip loading, side loading, binding, or bunching.

Shackle side-load reductions, eyebolt angular ratings, hoist-ring capacities, and termination efficiencies are manufacturer- and product-specific.

A missing required identification, damaged component, or unavailable rating is a stop condition—not an invitation to create a private derating.

Last updated: August 2026

  • Hardware Ratings, Identification, and Compatibility
  • Start with the rated load

Working load limit, rated load, and rated capacity identify the maximum load allowed under stated conditions. Use the marking, tag, manufacturer table, or approved lift plan for the exact component. A forged shape, paint color, pin diameter, or catalog look-alike does not prove identity or capacity.

The rating may depend on:

  • straight versus angular loading;
  • single- or multiple-leg use;
  • hitch type;
  • pin or bearing diameter;
  • temperature and chemical exposure;
  • thread engagement and installation torque;
  • load distribution in a hook, shackle, or link; and

whether rotation is allowed under load.

A rigger must know the load applied to the component and compare it with the applicable rating. Level I receives the needed load and configuration information; it does not calculate unknown sling tension.

Do not confuse strength terms

A design factor is the ratio used in design between a strength basis and rated load under specified assumptions. Minimum breaking force is a destructive strength measure. A proof test is a controlled test used to verify a component or assembly as required. None of those values is the everyday working load limit.

Do not multiply a stamped WLL by a remembered design factor. Do not operate at a proof-test load. Do not assume every item of hardware has the same factor. Different products and standards use different design methods.

Identification gate

Before use, confirm required identification is present and legible. Depending on the item, it can include manufacturer or trademark, size, grade, rated load, model, serial number, and traceability code. Sling tags also identify the rated capacities by hitch and sometimes angle.

If required identification is missing, the component is not made serviceable by measuring it or comparing it with another item. Remove it from service until an authorized process establishes identity and fitness. Never restamp or retag gear without the responsible manufacturer or qualified process.

Fit and bearing

Capacity is meaningful only if the connection fits. Check that:

  • the load bears in the intended saddle, bow, pin, eye, or jaw;
  • the mating part has adequate diameter and surface;
  • the connection can align with the force without prying;
  • the hook tip or latch does not carry load;
  • sling eyes are not crushed, folded, or forced to bunch;
  • a shackle pin is not bent by an oversized hook or narrow lug;
  • threads are fully and correctly engaged; and

moving parts can articulate without opening, loosening, or side loading.

Do not use makeshift bolts in place of shackle pins. Do not force a thick eye onto a small hook or use spacers unless the manufacturer permits the arrangement. Multiple sling eyes that crowd a hook should be collected with compatible, rated hardware specified for the configuration.

Product-specific angular rules

Shackles can have manufacturer side-loading reductions and restrictions for multiple loads in the bow. Those percentages are not universal across all designs. Center the load and use the manufacturer's table when a permitted side load is unavoidable.

A plain, non-shouldered eyebolt is generally intended for in-line loading only. A shouldered eyebolt may permit angular loading only when installed and loaded within its product instructions. Its capacity percentage, thread depth, shoulder seating, washer use, and required torque are product-specific.

A swivel hoist ring is designed to align more freely than a fixed eyebolt, but “swivel” does not mean full capacity at every angle for every model. It must be installed into suitable material with the required engagement and torque and must pivot and rotate freely before loading. The lifting member must not bind against the load.

Shackles, hooks, and pins

Choose the shackle style and pin retention for the task. Screw-pin shackles are convenient for connections that can be monitored and are not subject to pin-rotating action. Bolt-type shackles use a bolt, nut, and retaining pin for more secure retention. Round-pin designs have limited suitable applications; follow their manufacturer.

Seat hook loads in the bowl and keep the latch free of load. A latch retains slack rigging; it is not a structural support. Hook dimensional removal criteria come from B30.10, OSHA where applicable, and the manufacturer.

Tighten screw pins as the manufacturer and task instructions require. The current CCO practical instructions say hardware that normally requires final torque need only be finger-tight for the exam task. That exam accommodation is not a universal field assembly rule, and deliberately backing a shackle pin off is not a sound default.

Clips and terminations

OSHA construction rules prohibit using wire-rope clips or knots to fabricate eyes in wire-rope bridles, slings, or bull wires. For other allowed clip applications, use the controlling table and manufacturer instructions, including the correct number, spacing, torque, re-torque, and orientation. Under OSHA's U-bolt clip arrangement, the U-bolt goes on the dead end.

Do not assign a universal termination efficiency. Wedge sockets, poured sockets, swaged sleeves, thimbles, clips, and other terminations have different rules. Inspect the entire termination and use only the approved rope, socket, and assembly method.

Capacity decision sequence

Read the component identity and exact WLL.

Confirm the supplied force and loading direction.

Check that the configuration appears in the rating source.

Inspect condition and function.

Verify compatible fit and retention.

Apply any permitted reduction from the exact source.

If any fact is missing, stop.

“Looks strong enough” and “we used one like it before” are not rating methods.