Study guide

3.4 Feedwater Systems, Deaerators, Condensate Return & Boiler Water Treatment

NCCER Boilermaker Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: The Assessment, Boilermaker Craft, Safety, Tools & Crew Leadership

1.1 The NCCER Boilermaker Assessments: Format, Content Domains, Scoring & Credentials 1.2 Craft Fundamentals, Professional Roles & Industrial Safety 1.3 Confined Space Entry, Lockout/Tagout (LOTO) & Atmospheric Testing 1.4 Hand, Pneumatic, Electric & Hydraulic Boilermaker Tools 1.5 Crew Leadership, Job Planning, Production Tracking & Jobsite Communication

2 Chapter 2: Metallurgy, Base Materials, Oxyfuel, Air Carbon Arc & Plasma Cutting

2.1 Industrial Boiler Materials, Carbon & Alloy Steels, ASME Material Specs & Markings 2.2 Base Metal Surface Preparation, Joint Beveling & Fit-Up Cleanliness 2.3 Oxyfuel Cutting Principles, Equipment Setup, Torch Angles & Piercing Techniques 2.4 Air Carbon Arc Cutting and Gouging (CAC-A): Electrodes, Current, Air Supply, Technique & Defects 2.5 Plasma Arc Cutting (PAC): Torch Anatomy, Consumables, Gas Selection, Cut Quality & Safety

3 Chapter 3: Boiler Types, Steam Generation, Feedwater & Combustion Systems

3.1 Firetube Boiler Designs, Circulation Patterns & Operating Principles 3.2 Watertube Boiler Configurations, Natural & Forced Circulation, Drum Internals 3.3 Superheaters, Reheaters, Economizers & Air Heaters 3.4 Feedwater Systems, Deaerators, Condensate Return & Boiler Water Treatment 3.5 Combustion Systems: Burners, Stokers, Pulverizers, Fans & Draft Control

4 Chapter 4: Boiler Pressure & Nonpressure Components

4.1 Steam Drums, Mud Drums, Headers & Waterwalls 4.2 Nonpressure Components: Casing, Breeching, Baffles, Buckstays & Expansion Joints 4.3 Boiler Auxiliaries: Soot Blowers, Safety Valves, Gage Glasses & Blowdown Systems

5 Chapter 5: Valves, Gaskets, Fasteners, Anchors & Pipe Support Systems

5.1 Industrial Valve Types, Markings, Operation & Ratings 5.2 Gasket Materials, Flange Facings, Bolt Torque Sequences & Joint Assembly 5.3 Gasket Layout, Cutting & Fitting for Field-Made Gaskets 5.4 Fasteners, Anchors & Threaded Connection Hardware 5.5 Pipe Hangers, Supports, Rigid Restraints & Spring Can Installation/Adjustment

6 Chapter 6: Blueprint Reading, Welding Symbols & Construction Drawings

6.1 AWS Welding Symbols, Joint Geometry, Contours & NDE Designators 6.2 Piping Schematics, P&IDs, Isometric Drawings & Spool Sheets 6.3 Pressure Vessel General Arrangement, Detail Sheets, Coordinates & Elevations

7 Chapter 7: Trade Mathematics & Pipe Layout Calculations

7.1 Boilermaker Mechanical Trade Math: Offsets, Rolling Offsets & Travel Calculations 7.2 Vessel Volume, Surface Area, Circumference & Head Layout Computations 7.3 Mitered Turns, Segment Layout, Cutbacks & Branch Connections

8 Chapter 8: Pipe Fabrication - Socket Weld, Butt Weld, Threaded, Grooved & Spool Work

8.1 Pipe Materials, Nominal Pipe Size, Wall Schedules & Fitting Standards 8.2 Socket Weld Pipe Fabrication: The 1/16 in. Gap, Fillet Sizing & Cut Lengths 8.3 Butt Weld Pipe Fabrication: End Preparation, Alignment, Fit-Up & Cut Lengths 8.4 Pipe Layout Tools, Wrap-Arounds, Flange Squaring & Fabrication Tolerances 8.5 Threaded and Grooved Pipe Joining Systems 8.6 Spool Fabrication Workflow, Shop Versus Field Welds & Advanced Pipe Fabrication

9 Chapter 9: Tube Fabrication, Bending & Rolling

9.1 Boiler Tube Removal, Inspection, Wall Thinning & Replacement Criteria 9.2 Tube Preparation, Bending Radii, Ovality & Alignment Tolerances 9.3 Tube Expanding Mechanics, Rolling Torque Calculations, Wall Reduction & Flaring/Beading

10 Chapter 10: Welding Processes, Preheat & Stress Relieving

10.1 SMAW, GTAW & FCAW Welding Processes in Pressure Vessel Applications 10.2 Electrode Selection, Storage, Baking & AWS Filler Metal Classifications 10.3 Preheating Standards, Interpass Temperature Control & Post-Weld Heat Treatment (PWHT)

11 Chapter 11: Rigging Equipment, Hardware & Crane Operations

11.1 Rigging Hardware: Slings, Shackles, Eye Bolts & Inspection Criteria 11.2 Rigging Math: Sling Angles, Tension Calculations & Center of Gravity 11.3 Crane Signals, Load Charts, Boom Angle Deratings & Critical Lift Planning

12 Chapter 12: Towers, Heat Exchangers & Refractory/BRIL Systems

12.1 Shell-and-Tube Heat Exchangers: Bundles, Baffles & Floating Heads 12.2 Fractionation Towers, Trays, Downcomers, Packing & Vessel Hardware 12.3 Refractory Materials (Brick, Castable, Ceramic Fiber), Anchoring & Lagging (BRIL)

13 Chapter 13: ASME Codes, Quality Assurance, NDE, Pressure Testing & System Cleaning

13.1 ASME Boiler & Pressure Vessel Code (Sections I, VIII, IX) & NBIC Standards 13.2 Quality Control, Material Test Reports (MTRs), Weld Mapping & Traceability 13.3 Nondestructive Examination (NDE): VT, PT, MT, UT, RT & Discontinuity Evaluation 13.4 Hydrostatic and Pneumatic Testing Procedures, Safety Precautions & MAWP Validation 13.5 System Flushing, Chemical Cleaning, Boil-Out, Steam Blows & Service Leak Testing

3.4 Feedwater Systems, Deaerators, Condensate Return & Boiler Water Treatment

Key Takeaways Explain This Topic AI

The deaerator storage section is elevated above the boiler feed pumps because DA water sits at saturation temperature and will flash and cavitate the pump without that NPSH margin.

A properly operating deaerator delivers residual dissolved oxygen at or below 0.005 cc/L, roughly 7 parts per billion, and it cannot do so with the vent throttled shut.

Cycles of concentration equal boiler water TDS divided by feedwater TDS, and percent blowdown equals 100 divided by cycles.

Sodium sulfite is a low- and intermediate-pressure oxygen scavenger; hydrazine and other volatile scavengers are used on high-pressure units because they add no dissolved solids.

Oxygen pitting, caustic gouging, hydrogen damage and hard scale are all feedwater chemistry failures, not tube material failures.

Last updated: August 2026

Feedwater Systems, Deaerators, Condensate Return & Boiler Water Treatment

Core Trade Concept: Module 34201 covers boiler systems , not just the pressure parts. Nearly every boiler tube failure a boilermaker is called to repair — oxygen pitting, caustic gouging, hydrogen damage, scale-driven overheating — is a water chemistry failure that arrived through the feedwater train . Understanding the train tells you why the tube failed, which is the difference between replacing a tube and fixing a problem.

  • 1. The Feedwater Train, End to End STEAM to process/turbine
  • |
  • [ CONDENSER / PROCESS ]
  • | condensate
  • [ CONDENSATE RECEIVER ] --- makeup water (softened / demineralized)
  • |
  • [ DEAERATOR (DA) ] <-- pegging steam; removes O2 and CO2
  • | DA storage section (elevated for NPSH)
  • [ BOILER FEED PUMPS ] multistage centrifugal, min-flow recirc
  • |
  • [ FEEDWATER REGULATOR / CONTROL VALVE ]
  • |
  • [ ECONOMIZER ] <-- final flue-gas heat pickup
  • |
  • [ STEAM DRUM ] via feedwater distribution pipe

Two arrangement details are commonly tested:

The deaerator storage tank is mounted high — typically well above the boiler feed pump suction — because DA water sits at saturation temperature. Any drop in suction pressure flashes it to steam and the pump cavitates. That elevation is the net positive suction head (NPSH) margin.

A minimum-flow recirculation line runs from the pump discharge back to the DA. A boiler feed pump operating at or near shutoff head with no flow will overheat and destroy itself in minutes.

2. The Deaerator: Mechanical Oxygen Removal

Dissolved oxygen is the single most aggressive corrodent in a boiler system. The deaerator removes it physically, using Henry's Law : the solubility of a gas in water falls toward zero as the water approaches its saturation temperature at the operating pressure.

Type Mechanism

Spray-type Feedwater is sprayed through nozzles into a steam atmosphere, heating it to saturation and releasing gas

Tray-type Water cascades over stacked stainless trays counter-current to rising steam, giving a very large contact area

Spray-scrubber Spray section for bulk heating, followed by a scrubbing section for final polishing

Typical operation is around 5 psig, which corresponds to roughly 227°F saturation temperature.

A properly operating deaerator delivers residual dissolved oxygen at or below 0.005 cc/L (about 7 parts per billion) — the standard performance guarantee for this equipment.

The vent must stay open. A deaerator with the vent throttled shut cannot expel the liberated gas, and it silently stops deaerating while all pressure and temperature indications look normal. A visible plume at the vent is a working DA.

Chemical scavenging finishes the job

Scavenger Application

Sodium sulfite Low- and intermediate-pressure boilers. Adds dissolved solids, and it decomposes at high temperature, so it is generally excluded from high-pressure units (commonly cited as above roughly 900 psig)

Hydrazine / carbohydrazide High-pressure and utility boilers. Volatile, adds no solids, also passivates surfaces to magnetite

  • DEHA and other volatile scavengers Modern replacements where hydrazine handling is restricted
  • 3. Internal Treatment and Blowdown Control

Once water is in the boiler, treatment has three jobs: keep hardness from forming hard scale, hold pH in the passive range, and keep dissolved solids below carryover limits.

Phosphate treatment precipitates residual calcium as a soft, non-adherent sludge that leaves with the bottom blowdown, and buffers pH. Coordinated and congruent phosphate programs constrain the sodium-to-phosphate ratio specifically to prevent free caustic from concentrating under deposits.

All-volatile treatment (AVT) — ammonia plus a volatile scavenger, no solids — is used on high-pressure drum units and is mandatory on once-through supercritical boilers, which have no drum and therefore no blowdown path to remove solids at all .

Cycles of concentration links blowdown rate to water quality: Cycles = Boiler water TDS Feedwater TDS % Blowdown = 100 Cycles \text{Cycles} = \frac{\text{Boiler water TDS}}{\text{Feedwater TDS}} \qquad \%\ \text{Blowdown} = \frac{100}{\text{Cycles}} Cycles = Feedwater TDS Boiler water TDS ​ % Blowdown = Cycles 100 ​

Worked example. Feedwater at 40 ppm TDS, boiler water limit 2,000 ppm TDS: Cycles = 2000 40 = 50 % Blowdown = 100 50 = 2 % \text{Cycles} = \frac{2000}{40} = 50 \qquad \%\ \text{Blowdown} = \frac{100}{50} = 2\% Cycles = 40 2000 ​ = 50 % Blowdown = 50 100 ​ = 2%

Two percent of steaming rate must leave as blowdown. Reducing blowdown below that point drives boiler water TDS above the limit and starts carryover; raising it far above wastes fuel with every pound of hot water dumped.

Silica gets its own limit because silica is volatile at high pressure: it leaves the drum with the steam rather than staying in the water, and deposits as glass-hard scale on turbine blades. Permitted boiler-water silica falls steeply as drum pressure rises.

4. Reading a Failure Back to the Chemistry

Damage seen by the boilermaker Chemistry cause

Deep, sharp-edged pits on the waterside, often under a small tubercle Dissolved oxygen — failed deaeration or an air in-leak on the condensate side

Caustic gouging : irregular, smooth-walled thinning under a deposit Free caustic concentrating beneath porous deposits

Hydrogen damage : brittle, thick-lipped "window" blowout with no ductility Acidic under-deposit corrosion; atomic hydrogen reacting with iron carbide

Hard, adherent scale and short-term overheating bulges Hardness breakthrough from a failed softener or condensate contamination

Turbine deposits, wet steam, drum level instability Carryover — TDS or silica above limits, or a damaged separator

This table is why a boilermaker on an outage should always ask what the water chemistry logs show before assuming the tube simply "wore out."

5. What the Boilermaker Actually Builds and Repairs

Deaerator vessels crack. DA storage tanks and the head/shell weld seams are a well-known cracking location because of corrosion fatigue in a hot, cycling, two-phase environment. Wet fluorescent magnetic particle inspection of DA welds during outages, and weld repair to NBIC rules, is standard boilermaker scope.

Economizer tube and header replacement , including cold-end corrosion damage covered in Section 3.3.

Feedwater piping and the drum feedwater distribution pipe , which must be reinstalled with the correct orientation so cold feedwater is dispersed rather than jetted at the hot drum wall.

Condensate receiver and DA piping , where oxygen in-leakage on the vacuum side of the system is a chronic problem.

6. Realistic Trade Scenario: Pitting in a Reinstalled Economizer

A plant replaces an economizer bank during a two-week outage. Six months later boroscope inspection finds fresh oxygen pitting on the inlet rows.

The crew leader walks it back through the train rather than blaming the tube supplier:

Was the bank wet-layup or dry-layup during the remaining outage? An economizer left full of untreated, aerated water for ten days will pit before it is ever fired.

Is the DA vent open? Plant operations had throttled the DA vent to reduce steam loss during the low-load restart period.

Is the sulfite residual being maintained at the boiler feed pump suction, not just dosed at the DA?

Are there air in-leaks on the condensate return? Sub-atmospheric condensate lines pull air in through packing and joints.

The physical repair is straightforward; the value the crew adds is identifying that the throttled DA vent, not the tube material, put the pits there.