Study guide
3.3 Superheaters, Reheaters, Economizers & Air Heaters
NCCER Boilermaker Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: The Assessment, Boilermaker Craft, Safety, Tools & Crew Leadership
1.1 The NCCER Boilermaker Assessments: Format, Content Domains, Scoring & Credentials 1.2 Craft Fundamentals, Professional Roles & Industrial Safety 1.3 Confined Space Entry, Lockout/Tagout (LOTO) & Atmospheric Testing 1.4 Hand, Pneumatic, Electric & Hydraulic Boilermaker Tools 1.5 Crew Leadership, Job Planning, Production Tracking & Jobsite Communication
2 Chapter 2: Metallurgy, Base Materials, Oxyfuel, Air Carbon Arc & Plasma Cutting
2.1 Industrial Boiler Materials, Carbon & Alloy Steels, ASME Material Specs & Markings 2.2 Base Metal Surface Preparation, Joint Beveling & Fit-Up Cleanliness 2.3 Oxyfuel Cutting Principles, Equipment Setup, Torch Angles & Piercing Techniques 2.4 Air Carbon Arc Cutting and Gouging (CAC-A): Electrodes, Current, Air Supply, Technique & Defects 2.5 Plasma Arc Cutting (PAC): Torch Anatomy, Consumables, Gas Selection, Cut Quality & Safety
3 Chapter 3: Boiler Types, Steam Generation, Feedwater & Combustion Systems
3.1 Firetube Boiler Designs, Circulation Patterns & Operating Principles 3.2 Watertube Boiler Configurations, Natural & Forced Circulation, Drum Internals 3.3 Superheaters, Reheaters, Economizers & Air Heaters 3.4 Feedwater Systems, Deaerators, Condensate Return & Boiler Water Treatment 3.5 Combustion Systems: Burners, Stokers, Pulverizers, Fans & Draft Control
4 Chapter 4: Boiler Pressure & Nonpressure Components
4.1 Steam Drums, Mud Drums, Headers & Waterwalls 4.2 Nonpressure Components: Casing, Breeching, Baffles, Buckstays & Expansion Joints 4.3 Boiler Auxiliaries: Soot Blowers, Safety Valves, Gage Glasses & Blowdown Systems
5 Chapter 5: Valves, Gaskets, Fasteners, Anchors & Pipe Support Systems
5.1 Industrial Valve Types, Markings, Operation & Ratings 5.2 Gasket Materials, Flange Facings, Bolt Torque Sequences & Joint Assembly 5.3 Gasket Layout, Cutting & Fitting for Field-Made Gaskets 5.4 Fasteners, Anchors & Threaded Connection Hardware 5.5 Pipe Hangers, Supports, Rigid Restraints & Spring Can Installation/Adjustment
6 Chapter 6: Blueprint Reading, Welding Symbols & Construction Drawings
6.1 AWS Welding Symbols, Joint Geometry, Contours & NDE Designators 6.2 Piping Schematics, P&IDs, Isometric Drawings & Spool Sheets 6.3 Pressure Vessel General Arrangement, Detail Sheets, Coordinates & Elevations
7 Chapter 7: Trade Mathematics & Pipe Layout Calculations
7.1 Boilermaker Mechanical Trade Math: Offsets, Rolling Offsets & Travel Calculations 7.2 Vessel Volume, Surface Area, Circumference & Head Layout Computations 7.3 Mitered Turns, Segment Layout, Cutbacks & Branch Connections
8 Chapter 8: Pipe Fabrication - Socket Weld, Butt Weld, Threaded, Grooved & Spool Work
8.1 Pipe Materials, Nominal Pipe Size, Wall Schedules & Fitting Standards 8.2 Socket Weld Pipe Fabrication: The 1/16 in. Gap, Fillet Sizing & Cut Lengths 8.3 Butt Weld Pipe Fabrication: End Preparation, Alignment, Fit-Up & Cut Lengths 8.4 Pipe Layout Tools, Wrap-Arounds, Flange Squaring & Fabrication Tolerances 8.5 Threaded and Grooved Pipe Joining Systems 8.6 Spool Fabrication Workflow, Shop Versus Field Welds & Advanced Pipe Fabrication
9 Chapter 9: Tube Fabrication, Bending & Rolling
9.1 Boiler Tube Removal, Inspection, Wall Thinning & Replacement Criteria 9.2 Tube Preparation, Bending Radii, Ovality & Alignment Tolerances 9.3 Tube Expanding Mechanics, Rolling Torque Calculations, Wall Reduction & Flaring/Beading
10 Chapter 10: Welding Processes, Preheat & Stress Relieving
10.1 SMAW, GTAW & FCAW Welding Processes in Pressure Vessel Applications 10.2 Electrode Selection, Storage, Baking & AWS Filler Metal Classifications 10.3 Preheating Standards, Interpass Temperature Control & Post-Weld Heat Treatment (PWHT)
11 Chapter 11: Rigging Equipment, Hardware & Crane Operations
11.1 Rigging Hardware: Slings, Shackles, Eye Bolts & Inspection Criteria 11.2 Rigging Math: Sling Angles, Tension Calculations & Center of Gravity 11.3 Crane Signals, Load Charts, Boom Angle Deratings & Critical Lift Planning
12 Chapter 12: Towers, Heat Exchangers & Refractory/BRIL Systems
12.1 Shell-and-Tube Heat Exchangers: Bundles, Baffles & Floating Heads 12.2 Fractionation Towers, Trays, Downcomers, Packing & Vessel Hardware 12.3 Refractory Materials (Brick, Castable, Ceramic Fiber), Anchoring & Lagging (BRIL)
13 Chapter 13: ASME Codes, Quality Assurance, NDE, Pressure Testing & System Cleaning
13.1 ASME Boiler & Pressure Vessel Code (Sections I, VIII, IX) & NBIC Standards 13.2 Quality Control, Material Test Reports (MTRs), Weld Mapping & Traceability 13.3 Nondestructive Examination (NDE): VT, PT, MT, UT, RT & Discontinuity Evaluation 13.4 Hydrostatic and Pneumatic Testing Procedures, Safety Precautions & MAWP Validation 13.5 System Flushing, Chemical Cleaning, Boil-Out, Steam Blows & Service Leak Testing
3.3 Superheaters, Reheaters, Economizers & Air Heaters
Key Takeaways Explain This Topic AI
The thermodynamic steam generation cycle absorbs heat in three stages: sensible heat of liquid (raising water to saturation temperature), latent heat of vaporization (converting liquid to dry saturated steam at constant temperature), and superheat (raising dry steam temperature above saturation).
Primary radiant superheaters exhibit a drooping steam temperature curve with increasing boiler load, while secondary convective superheaters show a rising steam temperature curve; combining both in series achieves a stable steam temperature across broad load ranges.
Direct-contact spray-water attemperators (desuperheaters) regulate final superheated steam temperature by injecting polished feedwater through internal thermal sleeves that protect the pressure header from cyclic thermal shock and fatigue cracking.
Reheaters take cold reheat steam from the high-pressure turbine exhaust and restore it to 1,000–1,050°F at low pressure drop (<5–8% ΔP) to prevent condensation in intermediate-pressure turbine stages and maximize thermal cycle efficiency.
Economizers preheat feedwater from flue gas (each 10–11°F rise increases efficiency by ~1%), while air heaters preheat combustion air; both must operate above the sulfur acid dew point (240–300°F) to prevent severe cold-end sulfuric acid corrosion.
Last updated: August 2026
3.3 Superheaters, Reheaters, Economizers & Air Heaters
Core Trade Concept: Modern high-pressure boilers do not stop at generating saturated steam. To achieve high thermodynamic efficiency and protect steam turbines from moisture droplet erosion, boilers incorporate heat recovery systems: superheaters and reheaters (which add sensible heat to steam), economizers (which capture residual flue gas heat to preheat incoming feedwater), and air heaters (which preheat combustion air).
1. Thermodynamic Steam Cycle & Heat Transfer Principles
Converting subcooled feedwater into high-energy superheated steam occurs across three distinct thermodynamic heat absorption phases: TEMPERATURE - ENTHALPY HEAT ADDITION DIAGRAM
- Temp (^F) ^
- | / [ SUPERHEATING ] (Superheated Steam)
- | / Adds Sensible Heat (h_sup)
- T_sup +-------------------------------+ - - - - - - - - - - - - - - - -
- | [ VAPORIZATION ] |
- T_sat +-------------+=================+ (Dry Saturated Vapor, x = 1.0)
- | [ SENSIBLE | Latent Heat (h_fg)
- | HEATING |
- | OF WATER |
- | (h_f) |
- +-------------+-------------------------------------------------->
- Enthalpy (Btu/lb)
Sensible Heat of Liquid ( h f h_f h f ): Heat absorbed to raise water temperature from its subcooled inlet state up to the saturation temperature ( T s a t T_{sat} T s a t ) corresponding to boiler operating pressure. No steam is generated during this stage ( 1 Btu 1\text{ Btu} 1 Btu raises 1 lb 1\text{ lb} 1 lb of water by 1 ∘ F 1^\circ\text{F} 1 ∘ F ).
Latent Heat of Vaporization ( h f g h_{fg} h f g ): The massive quantity of heat required to change water from liquid at saturation temperature into dry saturated steam at the exact same temperature and pressure . As pressure increases, latent heat decreases until reaching zero at the critical point ( 3,206.2 psia 3{,}206.2\text{ psia} 3 , 206.2 psia , 705.1 ∘ F 705.1^\circ\text{F} 705. 1 ∘ F ).
Superheat ( h s u p h_{sup} h s u p ): Sensible heat added to dry saturated steam after it leaves the steam drum, raising its temperature above T s a t T_{sat} T s a t . Superheated steam contains no liquid moisture .
Saturation Temperature vs. Pressure Relationships
Boiler Pressure (psig) Saturation Temp T s a t T_{sat} T s a t ( ∘ F ^\circ\text{F} ∘ F ) Latent Heat h f g h_{fg} h f g (Btu/lb) Typical Superheated Steam Temp ( ∘ F ^\circ\text{F} ∘ F )
100 psig 100\text{ psig} 100 psig 338 ∘ F 338^\circ\text{F} 33 8 ∘ F 881 Btu/lb 881\text{ Btu/lb} 881 Btu/lb Saturated (Process heating)
600 psig 600\text{ psig} 600 psig 489 ∘ F 489^\circ\text{F} 48 9 ∘ F 732 Btu/lb 732\text{ Btu/lb} 732 Btu/lb 750 ∘ F 750^\circ\text{F} 75 0 ∘ F
1,500 psig 1{,}500\text{ psig} 1 , 500 psig 596 ∘ F 596^\circ\text{F} 59 6 ∘ F 557 Btu/lb 557\text{ Btu/lb} 557 Btu/lb 950 ∘ F 950^\circ\text{F} 95 0 ∘ F
2,400 psig 2{,}400\text{ psig} 2 , 400 psig 662 ∘ F 662^\circ\text{F} 66 2 ∘ F 381 Btu/lb 381\text{ Btu/lb} 381 Btu/lb 1,000 – 1,050 ∘ F 1{,}000\text{--}1{,}050^\circ\text{F} 1 , 000 – 1 , 05 0 ∘ F
3,206.2 psia 3{,}206.2\text{ psia} 3 , 206.2 psia (Critical) 705.1 ∘ F 705.1^\circ\text{F} 705. 1 ∘ F 0 Btu/lb 0\text{ Btu/lb} 0 Btu/lb 1,050 ∘ – 1,100 ∘ F 1{,}050^\circ\text{--}1{,}100^\circ\text{F} 1 , 05 0 ∘ – 1 , 10 0 ∘ F (Supercritical)
2. Superheaters: Types, Geometry & Characteristics
Superheaters are banks of high-alloy steel tubes (such as ASME SA-213 T11, T22, or T91) positioned in the hot flue gas path. They are categorized by heat transfer mode and physical arrangement: SUPERHEATER LOAD TEMPERATURE CHARACTERISTICS
- Steam Temp (^F) ^
- | / CONVECTIVE (Rises with load)
- | /------------------------------ COMBINED (Flat)
- | /
- | / \
- | / \ RADIANT (Droops with load)
- +--------------------------------------------->
- 0% 50% 100% Boiler Load
- Radiant vs. Convective Superheaters
Radiant Superheater: Located directly in the furnace wall or roof exposed to open flame radiation. At low boiler loads, flame temperature is high relative to steam flow, yielding high steam temperature. As load increases, steam flow increases faster than radiant heat transfer, causing steam temperature to decrease (droop) with increasing load.
Convective Superheater: Located in the gas convection pass shielded from direct flame radiation. As boiler load increases, the mass flow rate and velocity of hot flue gases increase, dramatically increasing convection heat transfer. Thus, steam temperature rises with increasing load.
Combined Superheater: By routing steam through a radiant superheater followed in series by a convective superheater, the opposing drooping and rising characteristics cancel out, maintaining a flat, stable superheat temperature across a wide load profile ( 25 % to 100 % 25\%\text{ to }100\% 25% to 100% load).
Pendant vs. Horizontal Superheater Tube Banks
Mechanical Feature Pendant Superheater Banks Horizontal Superheater Banks
Tube Orientation Hanging vertically from upper roof headers. Running horizontally across convective gas pass.
Drainability Non-drainable; bottom U-bends trap condensate when the boiler is offline. Fully drainable; tubes slope toward headers for complete gravity draining.
Startup Precaution Critical Rule: Trapped condensate plugs the tubes during startup. Low firing rates must be maintained until all water boils out to establish steam cooling flow before full firing, preventing rapid tube blowout. Water drains freely, permitting faster startup sequences with less risk of localized dryout.
Mechanical Support Suspended from structural roof steel via water-cooled hanger tubes. Supported on heavy cast alloy brackets attached to vertical waterwall tubes.
3. Steam Temperature Control & Attemperators (Desuperheaters)
To prevent over-temperature failure of superheater tubes and turbine components, the final superheat temperature must be controlled precisely ( ± 5 ∘ F \pm 5^\circ\text{F} ± 5 ∘ F ). This is accomplished using attemperators (also called desuperheaters ). SPRAY-WATER ATTEMPERATOR CONSTRUCTION
- Superheated Steam ===> +----------------------------------+ ===> Controlled Temp
- | [ Internal Thermal Sleeve ] | Superheated Steam
- | +----------------------------+ |
- | | ~~~~~~~~~~~~~~~~~~~~~ | |
- High-Purity Polish --->--+-> | * * Spray Nozzle * * | |--+
- Feedwater Injection | | ~~~~~~~~~~~~~~~~~~~~~ | |
- | +----------------------------+ |
- +----------------------------------+
- (Thermal sleeve prevents cold water from
- impinging on hot header shell wall)
Direct-Contact Spray Attemperators: High-pressure polished boiler feedwater is injected through a spray nozzle / atomizing venturi directly into the superheated steam flow between the primary and secondary superheaters. The fine mist flashes instantly into steam, absorbing heat and lowering the bulk steam temperature.
Boilermaker Quality Standard: An internal thermal sleeve (protective liner) must be installed inside the attemperator pipe. The thermal sleeve prevents cold spray water droplets from directly striking the hot outer pressure header, preventing catastrophic cyclic thermal shock and fatigue cracking of the pressure boundary.
Water Purity: Spray water must be high-purity polished condensate or deaerated feedwater with zero solid chemicals (no sodium phosphate), as any non-volatile solids would carry straight into the steam turbine.
Surface Attemperators (Indirect): Superheated steam passes through a heat exchanger bundle submerged inside the boiler steam drum or mud drum, rejecting excess heat indirectly to boiler water without mixing fluid streams.
4. Reheaters
In utility power plants, steam expands through the high-pressure (HP) turbine, dropping in pressure and temperature. To prevent moisture from condensing in the subsequent intermediate-pressure (IP) and low-pressure (LP) turbine stages, this steam is returned to the boiler through reheaters .
Cold Reheat: Exhaust steam from the HP turbine (typically 500 – 650 psig 500\text{--}650\text{ psig} 500 – 650 psig , 550 – 650 ∘ F 550\text{--}650^\circ\text{F} 550 – 65 0 ∘ F ) returns to the boiler reheater inlet header.
Hot Reheat: The reheater heats the steam back up to 1,000 – 1,050 ∘ F 1{,}000\text{--}1{,}050^\circ\text{F} 1 , 000 – 1 , 05 0 ∘ F at relatively low pressure before discharging it to the IP turbine.
Operating Rule (Pressure Drop): Because reheat steam is at lower pressure, reheater tubes have larger diameters and thinner walls than superheaters. Reheater circuits must be designed with extremely low pressure drop (typically < 5 – 8 % < 5\text{--}8\% < 5 – 8% of inlet pressure); excessive pressure drop destroys the thermodynamic heat-rate gains of the Rankine cycle.
Startup Protection: During initial boiler startup before the turbine rolls, no steam flows through the reheater. Burner firing rates must be strictly limited until turbine bypass systems establish cooling steam flow through reheater tube banks.
5. Economizers & Air Heaters BOILER FLUE GAS HEAT RECOVERY TRAIN
- Furnace Flue Gas ===> [ SUPERHEATER / REHEATER ] (High Temp Heat Recovery)
- |
- v
- [ ECONOMIZER TUBE BANK ] (Preheats Feedwater)
- |
- v
- [ AIR PREHEATER (APH) ] (Preheats Combustion Air)
- |
- v
- To Baghouse / FGD / Stack (Flue Gas at ~280-320^F)
- Economizers (Feedwater Preheating)
An economizer is a bank of serpentine tubes located in the low-temperature convective gas pass. It captures waste heat from the flue gas exiting the superheater zone to preheat boiler feedwater before it enters the steam drum.
Efficiency Rule of Thumb: Every 10 ∘ F to 11 ∘ F 10^\circ\text{F to }11^\circ\text{F} 1 0 ∘ F to 1 1 ∘ F increase in feedwater temperature produced by the economizer increases overall boiler thermal efficiency by approximately 1 % 1\% 1% (correspondingly, every 40 ∘ F 40^\circ\text{F} 4 0 ∘ F drop in flue gas stack temperature increases efficiency by 1 % 1\% 1% ).
Non-Steaming vs. Steaming Economizers:
Non-Steaming Economizer: The standard industrial design. Sized so exit water temperature remains 30 ∘ F to 50 ∘ F 30^\circ\text{F to }50^\circ\text{F} 3 0 ∘ F to 5 0 ∘ F below saturation temperature ( T s a t T_{sat} T s a t ) . This prevents steam bubble formation, eliminating severe water hammer and vapor locking in economizer tubes.
Steaming Economizer: Used in select utility boilers where 5 – 20 % 5\text{--}20\% 5 – 20% of water is intentionally vaporized. Requires upward water flow and no downward hairpin bends where vapor locks could form.
Air Preheaters (APH)
Air preheaters recover remaining heat from flue gas leaving the economizer to preheat incoming combustion air to 400 – 600 ∘ F 400\text{--}600^\circ\text{F} 400 – 60 0 ∘ F , dramatically improving combustion stability and furnace efficiency.
Tubular Recuperative Air Heaters: Stationary tube banks where hot flue gas passes through the inside of vertical tubes while ambient combustion air blows across the outside in multiple cross-flow passes. Zero cross-leakage between streams.
Regenerative Rotary Air Heaters (Ljungstrom / Rothemuhle): A slowly rotating ( 1 – 3 RPM 1\text{--}3\text{ RPM} 1 – 3 RPM ) cylindrical wheel packed with corrugated sheet metal "baskets." The baskets absorb heat while rotating through the hot flue gas sector, then rotate into the incoming cold air sector to release the heat into the combustion air stream.
Radial and Axial Seals: Flexible alloy "feather" seals minimize air-to-gas leakage across the high-to-low pressure sectors.
Soot Blowers: Steam soot blowers must operate regularly to remove fly ash deposits from narrow basket corrugations, preventing basket plugging and catastrophic air heater fires.
Cold-End Acid Dew Point Corrosion
When fuels contain sulfur (coal, heavy fuel oil), sulfur burns to sulfur dioxide ( S O 2 SO_2 S O 2 ), a small fraction ( 1 – 5 % 1\text{--}5\% 1 – 5% ) of which oxidizes into sulfur trioxide ( S O 3 SO_3 S O 3 ). In the flue gas, S O 3 SO_3 S O 3 combines with moisture ( H 2 O H_2O H 2 O ) to produce sulfuric acid vapor ( H 2 S O 4 H_2SO_4 H 2 S O 4 ): SO 3 + H 2 O ⟶ H 2 SO 4 \text{SO}_3 + \text{H}_2\text{O} \longrightarrow \text{H}_2\text{SO}_4 SO 3 + H 2 O ⟶ H 2 SO 4
If economizer tube metal or air heater cold-end basket temperatures drop below the acid dew point (typically 240 ∘ F to 300 ∘ F 240^\circ\text{F to }300^\circ\text{F} 24 0 ∘ F to 30 0 ∘ F depending on fuel sulfur content), concentrated sulfuric acid condenses directly onto the metal, causing rapid perforation, tube thinning, and structural collapse.
Safeguards: Deaerator temperature must maintain economizer inlet water above 250 ∘ F 250^\circ\text{F} 25 0 ∘ F , and steam coil air preheaters (SCAPH) are installed ahead of regenerative air heaters to preheat cold winter ambient air before it contacts the rotating baskets.