Study guide

Joists, Beams, Girders & Bridging

NCCER Carpenter Commercial Carpenter

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the NCCER Carpenter Assessment How to Use This Study Guide NCCER Registry, Credentials & Apprenticeship Path Exam Logistics, Calculator Rules & Study Strategy

2 Construction Safety for Carpenters

Construction Site Safety Orientation Fall Protection, Ladders & Scaffolds PPE, Hand/Power Tool & Nailer Safety Material Handling & Jobsite Housekeeping

3 Building Materials, Fasteners & Tools

Lumber Grades & Engineered Wood Products Fasteners, Anchors & Adhesives Carpenter Hand Tools Portable Power Tools

4 Floor Systems

Floor System Components & Layout Joists, Beams, Girders & Bridging Subfloor Installation & Engineered Floor Systems

5 Wall Systems & Building Envelope

Wall Framing Components & Layout Openings, Headers, Cripples & Bracing Wall Assembly, Plumb/Square & Sheathing Building Envelope, Moisture Control & Insulation Basics

6 Construction Drawings, Measurement & Site Layout

Plans, Elevations, Sections & Details Specifications, Codes, Symbols & Abbreviations Site Layout, Batter Boards & the 3-4-5 Method Leveling Instruments & Building Layout Construction Math, Scale Conversions & Material Takeoffs

7 Stair Systems

Stair Types & Components Rise, Run, Headroom & Code Requirements Stringers, Finished Stairs & Commercial Stair Systems

8 Roofing Applications & Systems

Roof Types, Underlayment & Thermal/Moisture Protection Residential Shingle Installation Sequence Commercial Roofing, Flashing & Ventilation Roof Framing Basics (Pitch, Common Rafters & Trusses)

9 Cold-Formed Steel Framing

CFS Materials, Gauges & Components Installing CFS Walls, Loadbearing vs Nonbearing

10 Drywall Installation & Finishing

Gypsum Board Types & Fastening Methods Installing Drywall on Walls & Ceilings Finishing Levels & Fire/Sound-Rated Assemblies

11 Interior Finish: Doors, Trim, Cabinets & Ceilings

Doors & Door Hardware Window, Door, Floor & Ceiling Trim Cabinet & Countertop Installation Suspended & Acoustical Ceilings Commercial Door Frames, Fire-Rated Assemblies & Hardware Sets

12 Exterior Finish & Trim

Exterior Siding Materials & Installation Flashing, House Wrap & Weather Barriers Exterior Trim, Soffit & Fascia

13 Rigging for Carpenters

Rigging Equipment, Hardware & Inspection Sling Angles, Hitches & Load Control Crane Awareness & Lift Planning for Carpenters

14 Concrete Properties, Reinforcement & Placement

Concrete Properties, Mixes & Curing Reinforcing Steel Selection & Placement Handling, Placing, Finishing & Joints

15 Foundations & Formwork

Foundations & Slab-on-Grade Forms Vertical & Horizontal Formwork Systems Tilt-Up Wall Construction Overview Formwork Loads, Shoring, Reshoring & Stripping

Joists, Beams, Girders & Bridging

Key Takeaways Explain This Topic AI

Joists bear on plates, beams, or hangers; double (or more) joists under partitions and at openings as the plans show

Beams and girders need adequate bearing length and correct fasteners or hardware at posts and walls

Bridging or mid-span blocking stiffens the floor, shares load between joists, and reduces rotation—install as specified

Notching and boring solid-sawn joists are limited near edges and mid-depth; when in doubt, follow code diagrams or engineer direction

  • I-joists: never notch flanges; cut web holes only per manufacturer charts; use listed hangers and stiffeners
  • Last updated: August 2026

Joists, Beams, Girders & Bridging

Quick Answer: Install joists to full bearing or in listed hangers , crown up , at plan spacing. Double joists under concentrated loads (partitions, tubs, openings) when detailed. Add bridging or blocking to stiffen the system. Respect notch/bore limits on solid-sawn lumber. For I-joists , never cut flanges, place web holes only where manufacturer charts allow, and use the correct hangers and web stiffeners .

After layout and sill work, the carpenter’s production speed depends on clean joist and beam installation. Module 27105 expects you to support members correctly, reinforce openings, control vibration with bridging/blocking, and avoid illegal cuts that destroy capacity.

Joist Bearing and Connections

Each joist end must transfer load into a support. Common details:

Lap or butt on a sill/plate or girder with the minimum bearing length required by code or design (often on the order of 1½" on wood or metal and more on masonry— use the drawing or code table , do not invent a single number for every case).

Metal joist hangers flush-framed to a beam or header—use the hanger model listed for the joist size and load; fill required nail holes with specified nails (not random screws unless the hanger listing allows them).

Ledger connections on existing walls (especially remodels)—bolting patterns and flashing matter; commercial ledgers often need engineering.

Keep joists tight to layout marks so subfloor edges land on framing. Toenailing alone is rarely enough where hangers are specified; hangers provide tested uplift and gravity capacity.

Doubled Joists, Headers, and Openings

Plans frequently call for double joists (two members nailed or bolted together) under:

  • Load-bearing partitions running parallel to joists
  • Heavy fixtures (some tubs, kitchen islands, safes—per detail)
  • Trimmers along stair openings and large shafts

Stair and chase openings use a framed box: headers (often doubled) carry cut joists ( tail joists ), and trimmers support the headers. Hangers are common at header-to-trimmer and tail-to-header connections. Never cut a joist for an opening without installing the designed header system—removing section without load path is how floors sag and fail inspection.

When partitions run perpendicular to joists, a single joist may be enough if the wall is non-bearing and the plan is silent—but bearing walls need continuous support (beam below, double joist, or wall stacked on support). Read the structural notes.

Beams and Girders

Girders collect joist loads and deliver them to posts, columns, or foundation walls. Types you will meet:

Type Notes for carpenters

Built-up lumber Multiple 2× members; nail/bolt per schedule; keep crowns aligned; joints in outer laminations staggered and supported

  • LVL / PSL High design values; keep dry; use compatible hangers; follow hole charts if any
  • Glulam Deep beams; watch camber and bearing; finish/appearance grades on exposed commercial work

Steel beam Wood joists often hang on welded seats or side-mounted hangers; fire protection and connections per commercial details

Bearing: Wood beams need full, level bearing on posts or walls. Undersized bearing concentrates stress and crushes fibers. Post caps, base hardware, and anchor patterns resist uplift and lateral movement—especially in high-wind or seismic regions.

Built-up beam joints: Do not align all butt joints in one vertical plane midspan. Stagger splices and locate them over supports unless the engineer details a designed splice.

Bridging and Blocking

Bridging (cross bridging with wood or metal braces) and solid blocking between joists serve similar purposes:

Load sharing — adjacent joists help carry a concentrated load.

Stiffness / vibration control — reduces bounce under foot traffic.

Lateral restraint — keeps joists from rolling or twisting under load.

Fire stopping — solid blocking can help compartmentalize cavities when required.

Codes and plans specify when bridging or mid-span blocking is required (often based on joist depth and span). Install bridging tight after the joists are aligned and before or as subfloor goes down per crew practice—loose bridging does little. For I-joists, manufacturers often specify bottom flange restraint , rim closure, and squash blocks or web stiffeners at bearings rather than traditional cross bridging alone; follow the product guide.

End blocking or full-depth rim closure at exterior walls keeps joist ends vertical and provides nailing for sheathing. At interior girders where joists lap, blocking may be required for load transfer and diaphragm continuity.

Notching and Boring — Solid-Sawn Joists (Conceptual Rules)

Cutting a joist reduces capacity. Building codes publish diagrams with maximum notch depths and hole diameters , and where along the span they may occur. Memorize the ideas , not a single fake dimension for every size:

Tension edge matters. For simple-span joists, the bottom edge at midspan is in tension; deep notches there are especially harmful. Notches are generally restricted near the ends (top or bottom within limited depth fractions) and prohibited in the middle third of the span on the tension edge in typical code diagrams.

Holes are usually placed in the middle of the depth (near neutral axis), not near top or bottom edges, with diameter limits as a fraction of joist depth, and edge-distance rules from the face.

Never notch or bore beyond code/manufacturer limits to run plumbing “because it fits.” Reroute, sister, or get an engineered fix.

Exam framing: If a question shows a large notch cut from the bottom of a joist at midspan, that is almost always not allowed . If a hole is tight to the top edge or larger than permitted fraction of depth, it is wrong . Exact fractions come from the code figure in force—choose the answer that respects location and relative size limits.

Engineered I-Joists — Different Rules

Wood I-joists (OSB or similar web with LVL or solid flanges) are lighter and straighter than many solid joists but fail differently :

Rule Practice

Flanges Do not notch, cut, or drill flanges except where the manufacturer explicitly allows (rare). Flanges are the chords—damage ruins capacity.

Web holes Cut only inside published hole charts (max size vs distance from support). Leave required edge distances.

Hangers Use hangers listed for that I-joist series and depth; seat fully; nail all required holes.

Stiffeners / squash blocks Add web stiffeners or squash blocks at bearings and under concentrated loads when the guide requires them.

Rim / closure Install rim board or closure panels that match depth for load path and fire/air details.

Field trap: Treating an I-joist like a 2×10 and cutting a big rectangular chunk from a flange for a pipe. That single mistake can condemn the member. Open-web floor trusses likewise forbid cutting webs or chords—only designated chase openings may be used.

Installation Quality Checklist

Layout matches plan direction and O.C. spacing.

Crowns up (solid sawn); I-joist stamps upright.

Bearing length or hanger engagement complete; correct nails in hangers.

Doubled members under partitions/openings as detailed; headers/trimmers complete.

Bridging/blocking installed tight where required.

No illegal notches/holes; I-joist webs only per chart.

Beams braced and posts plumb with hardware installed.

Solid joist craftsmanship plus disciplined engineered-product rules is a large share of floor-system items on journey-level assessments and the difference between a quiet, flat floor and a callback.