Study guide
Stair Types & Components
NCCER Carpenter Commercial Carpenter
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the NCCER Carpenter Assessment How to Use This Study Guide NCCER Registry, Credentials & Apprenticeship Path Exam Logistics, Calculator Rules & Study Strategy
2 Construction Safety for Carpenters
Construction Site Safety Orientation Fall Protection, Ladders & Scaffolds PPE, Hand/Power Tool & Nailer Safety Material Handling & Jobsite Housekeeping
3 Building Materials, Fasteners & Tools
Lumber Grades & Engineered Wood Products Fasteners, Anchors & Adhesives Carpenter Hand Tools Portable Power Tools
4 Floor Systems
Floor System Components & Layout Joists, Beams, Girders & Bridging Subfloor Installation & Engineered Floor Systems
5 Wall Systems & Building Envelope
Wall Framing Components & Layout Openings, Headers, Cripples & Bracing Wall Assembly, Plumb/Square & Sheathing Building Envelope, Moisture Control & Insulation Basics
6 Construction Drawings, Measurement & Site Layout
Plans, Elevations, Sections & Details Specifications, Codes, Symbols & Abbreviations Site Layout, Batter Boards & the 3-4-5 Method Leveling Instruments & Building Layout Construction Math, Scale Conversions & Material Takeoffs
7 Stair Systems
Stair Types & Components Rise, Run, Headroom & Code Requirements Stringers, Finished Stairs & Commercial Stair Systems
8 Roofing Applications & Systems
Roof Types, Underlayment & Thermal/Moisture Protection Residential Shingle Installation Sequence Commercial Roofing, Flashing & Ventilation Roof Framing Basics (Pitch, Common Rafters & Trusses)
9 Cold-Formed Steel Framing
CFS Materials, Gauges & Components Installing CFS Walls, Loadbearing vs Nonbearing
10 Drywall Installation & Finishing
Gypsum Board Types & Fastening Methods Installing Drywall on Walls & Ceilings Finishing Levels & Fire/Sound-Rated Assemblies
11 Interior Finish: Doors, Trim, Cabinets & Ceilings
Doors & Door Hardware Window, Door, Floor & Ceiling Trim Cabinet & Countertop Installation Suspended & Acoustical Ceilings Commercial Door Frames, Fire-Rated Assemblies & Hardware Sets
12 Exterior Finish & Trim
Exterior Siding Materials & Installation Flashing, House Wrap & Weather Barriers Exterior Trim, Soffit & Fascia
13 Rigging for Carpenters
Rigging Equipment, Hardware & Inspection Sling Angles, Hitches & Load Control Crane Awareness & Lift Planning for Carpenters
14 Concrete Properties, Reinforcement & Placement
Concrete Properties, Mixes & Curing Reinforcing Steel Selection & Placement Handling, Placing, Finishing & Joints
15 Foundations & Formwork
Foundations & Slab-on-Grade Forms Vertical & Horizontal Formwork Systems Tilt-Up Wall Construction Overview Formwork Loads, Shoring, Reshoring & Stripping
Stair Types & Components
Key Takeaways Explain This Topic AI
Stair types include straight-run, L-shaped (with landing), U-shaped (switchback), spiral, and winder stairs—each trades footprint, cost, and code complexity
Stringers (carriages) carry the loads; treads are the walking surfaces; risers close the vertical face between treads
Landings break long flights, change direction, and provide rest; handrails and guards protect the open sides of the run and landings
Newels, balusters, and nosing complete the finished assembly and control grip, spacing, and tread edge projection
Name every part on a section sketch before you calculate rise/run—Module 27110 and Commercial Carpenter stair items test vocabulary first
Last updated: August 2026
Stair Types & Components
Quick Answer: Stairs move people between levels with treads (horizontal walking surfaces) and risers (vertical faces), supported by stringers (carriages). Landings change direction or break long flights. Handrails and guards protect users; newels , balusters , and nosing finish the assembly. Know straight , L , U , spiral , and winder layouts so you can read plans, order materials, and frame openings correctly.
Module 27110 (Basic Stair Layout) and Module 27405 (Finished Stairs) sit inside the Stair Systems domain on the Commercial Carpenter assessment (about 6 items ). Items expect you to identify types and parts, then apply rise/run and stringer skills in the next sections. Start with vocabulary—if you misname a stringer as a joist or a guard as a handrail, every calculation and code answer that follows is at risk.
Why Stair Literacy Matters on the Job
A stair is a permanent vertical circulation system, not a decorative ladder. Wrong type for the footprint forces redesign. Missing a landing when code requires one fails inspection. Confusing handrail height with guard height produces unsafe, noncompliant work. Commercial carpenters also coordinate stair openings with floor framing (headers, trimmers), fire ratings, and accessibility notes—so the names on the plan must match the members you build.
Stair Types (Plan Geometry)
Stair type describes how the run occupies plan space and whether the path turns.
- Type Description Typical use / trade-offs
- Straight-run Single flight between two levels, no turn Simplest layout and framing; needs a long clear length
L-shaped (quarter-turn) Two runs at ~90° with a landing (or winders) at the turn Fits into a corner; landing is preferred over winders for comfort/code clarity
U-shaped (switchback / half-turn) Two parallel runs with a landing (or intermediate landing) reversing direction Compact floor opening; common in multi-story residential and commercial cores
Spiral Treads radiate around a center pole or open well Very small footprint; special code limits on width, rise, and use (often restricted as primary exit)
Winder Tapered treads that turn without a full rectangular landing Saves space; harder to layout; walk line and minimum tread depth rules apply
Straight-run stairs are the teaching default. One total rise, one total run, identical unit risers and treads end to end. Header and trimmer framing for the stairwell is rectangular and relatively simple.
L-shaped stairs place a landing at the corner so each flight stays a normal rectangular run. That is usually safer and easier to code-check than packing the turn with winders. On plans, look for a square or rectangular platform at the turn with handrails continuing or restarting per detail.
U-shaped stairs reverse direction 180°. Two flights share a common wall or open well; the intermediate landing may be a full-width platform. Multi-story commercial stairs often stack U-shaped flights in a rated stair shaft.
Spiral stairs use pie-shaped treads around a center support. They appear as secondary access (e.g., loft, mezzanine) more often than as the primary means of egress. Exam awareness: spirals have special dimensional limits and are not interchangeable with a straight residential stair under ordinary IRC assumptions.
Winder stairs turn the path with tapered treads instead of (or in addition to) a landing. Layout uses a walk line (typically offset from the handrail side) where tread depth is measured. Winders require careful marking so the narrow end never drops below code minimums at the walk line. Many jurisdictions prefer landings for primary stairs; treat winders as a specialized layout skill, not the default solution.
Scenario: A remodel must fit stairs into a 4' × 4' corner of a foyer. A straight-run will not fit the length available. An L-shaped stair with a landing in the corner usually solves geometry better than forcing a straight flight or an unplanned spiral. If the plan shows winders, verify walk-line tread depths before cutting stringers.
- Primary Structural Components
- Stringers (Carriages)
Stringers —also called carriages or stair horses—are the inclined structural members that support treads and risers. Common arrangements:
Cut (open) stringers: Triangular notches cut for each tread and riser; treads sit on the horizontal cuts.
Housed (closed) stringers: Grooves (housings) routed into the stringer face; treads and risers slide into the grooves and are wedged/glued—common on finish stairs.
Center carriage: Extra stringer under wide stairs to reduce tread span.
Solid lumber (often 2×12 for cut residential stringers), LVL, or engineered stringers appear on commercial work. Outer stringers may be finish stringers with a rough carriage behind them. Always support stringers on solid framing at the top (header/trimmer or landing) and bottom (floor, pad, or kick plate)—not on finish flooring alone unless designed that way.
Treads and Risers
Tread: The horizontal board or pan you step on. Depth (unit run) is measured as the horizontal distance from face of riser to face of riser (or nosing to nosing rules per code definition).
Riser: The vertical board or face between consecutive treads. Closed risers fill the space; open-riser stairs omit solid risers where allowed.
Nosing: The projection of the tread beyond the face of the riser below. Nosing improves foot placement and is limited/required by code ranges in many residential models.
Treads may be rough framing lumber later covered by finish treads, solid hardwood finish treads, or metal/concrete pans in commercial systems. Risers may be wood, drywall-faced, metal, or open.
Landings
A landing is a level platform at the top, bottom, or intermediate point of a stair. Functions:
- Change of direction (L or U stairs)
- Break long vertical travel into code-compliant flight lengths
Provide a rest and a safe door swing area (doors should not swing into the required landing width in a way that reduces clearances)
Support stringer ends and handrail transitions
Landings are framed like miniature floors: joists or solid blocking, subfloor or deck, and perimeter support. Commercial landings may be steel pan with concrete fill or precast.
Safety and Finish Components
- Component Role
- Handrail Graspable rail along the stair run for balance; height measured to the nosing line per code
Guard (guardrail) Barrier at open sides of stairs, landings, and balconies to prevent falls; height and opening limits apply
Newel (newel post) Vertical post at ends/turns that anchors handrails and balustrades
Baluster (spindle) Vertical infill between rail and tread/floor; spacing limited so a sphere of specified diameter cannot pass
- Handrail return / wall rail Rail that returns to wall or newel so clothing/bags do not catch on open ends
- Skirt board (finish stringer face) Finish board along wall side of stair covering cut edges
Handrail vs guard: A handrail is for gripping while ascending/descending . A guard is a fall barrier at open sides. On open stairs they may combine (a guard with a graspable handrail on top or a separate handrail inside the guard). Exam trap: applying handrail height numbers to a balcony guard, or vice versa.
Balusters and openings: Infill must keep openings small enough that a child cannot pass through—model residential codes commonly use a 4-inch sphere test at guards (and often a different sphere size at certain stair openings). Use the figure in force for the job; the concept is maximum clear opening, not decorative preference.
Nosing: Beyond grip and edge definition, nosing dimensions affect effective tread depth. When you lay out stringers, nosing and finish tread thickness interact with drop calculations (next sections).
Reading Stairs on Drawings
Stair-related plan and section notes typically show:
Number of risers and treads (note: number of treads is usually one less than number of risers in a simple flight between floors)
- Direction of travel arrows and "UP" / "DN"
- Stair width, landing sizes, and handrail locations
- Headroom notes and stairwell opening dimensions
- Material callouts (wood, steel pan, precast, etc.)
A section cut through the stair shows total rise, unit rise/run, headroom, and how stringers bear on floor framing. Match the section to the plan flight you are building—U-shaped stairs have multiple sections.
Commercial vs Residential Awareness
Residential teaching models often use wood cut stringers, wood treads/risers, and IRC-style dimensions. Commercial stair systems may use:
- Steel stringers with pan treads filled with concrete
- Prefabricated metal stairs set into shafts
- Rated enclosures, standpipes, and exit signage coordination
- Larger widths, different handrail extensions, and accessibility (ADA) criteria on accessible routes
Component names stay the same even when materials change. A pan tread is still a tread; a channel stringer is still a stringer.
Field Vocabulary Checklist
Before layout day, walk the crew through the sketch and name:
- Top and bottom landings
- Number of risers in each flight
- Left/right stringers and any center carriage
- Tread material and whether risers are open or closed
- Handrail side(s), newel locations, guard requirements
- Nosing type and finish thickness (affects stringer drop later)
Mastering types and components turns Module 27110 drawings into a parts list. The next section converts total floor-to-floor height into equal unit rises and runs that those stringers must carry.