Study guide
1.3 Personal Protective Equipment (PPE) Selection, Inspection, and Maintenance
NCCER Core Curriculum: Introductory Craft Skills Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Basic Safety Fundamentals & OSHA Regulations
1.1 Safety Culture, Incident Costs, and OSHA Regulations 1.2 Hazard Recognition, Job Safety Analysis (JSA), and the Hierarchy of Controls 1.3 Personal Protective Equipment (PPE) Selection, Inspection, and Maintenance
2 Chapter 2: Elevated Work, Scaffolding & Electrical Safety
2.1 Fall Protection Systems: Guardrails, Safety Nets, and Personal Fall Arrest Systems (PFAS) 2.2 Ladder Safety Standards and Scaffolding Requirements 2.3 Electrical Hazards, Ground Fault Protection (GFCI), and Lockout/Tagout (LOTO)
3 Chapter 3: Health Hazards, Fire Protection & Chemical Safety
3.1 Confined Space Entry, Trenching, and Excavation Safety 3.2 Fire Protection, Extinguisher Classifications, and Job-Site Fire Prevention 3.3 Hazard Communication (HazCom), GHS Pictograms, and Safety Data Sheets (SDS)
4 Chapter 4: Trade Mathematics: Arithmetic & Fractions
4.1 Whole Number Operations and Trade Estimations 4.2 Fraction Arithmetic, Common Denominators, and Tape Measure Calculations 4.3 Decimal Operations and Conversions Between Fractions, Decimals, and Percentages
5 Chapter 5: Trade Mathematics: Geometry & Measurement
5.1 Linear Measurement, Reading Imperial and Metric Rules, and Unit Conversions 5.2 Area and Perimeter Calculations for Craft Layouts 5.3 Volume Calculations and Concrete/Material Estimations 5.4 Right Triangles, Angles, and the Pythagorean Theorem (3-4-5 Rule)
6 Chapter 6: Hand Tools: Striking, Fastening & Holding
6.1 Striking Tools and Demolition/Prying Equipment 6.2 Screwdrivers, Wrenches, Sockets, and Torque Wrenches 6.3 Pliers, Clamps, and Vises in Construction
7 Chapter 7: Hand Tools: Cutting, Shaping & Layout
7.1 Handsaws, Hacksaws, Chisels, Files, Knives, and Digging Tools 7.2 Levels, Plumb Bobs, and Chalk Lines 7.3 Framing Squares, Speed Squares, and Layout Procedures
8 Chapter 8: Power Tools: Drills, Saws & Power Sources
8.1 Power Tool Safety Principles, Power Sources, and Electrical Protection 8.2 Electric Drills, Hammer Drills, Rotary Hammers, and Impact Drivers 8.3 Power Saws: Circular, Reciprocating, Jigsaw, Band, Table, and Miter Saws
9 Chapter 9: Power Tools: Grinders, Pneumatic & Fastening Tools
9.1 Angle Grinders, Bench Grinders, Cut-Off Saws, and Oscillating Multi-Tools 9.2 Pneumatic Tools, Air Compressors, and Hose Safety 9.3 Powder-Actuated Fastening Systems and Hydraulic Tools
10 Chapter 10: Construction Drawings: Fundamentals & Line Types
10.1 Components of Construction Drawings: Title Blocks, Revision Blocks, and Legends 10.2 Types of Construction Drawings: Civil, Architectural, Structural, and MEP Plans 10.3 The Alphabet of Lines, Symbols, and Drawing Abbreviations
11 Chapter 11: Construction Drawings: Scales & Plan Views
11.1 Reading Architect's and Engineer's Scales 11.2 Plan Views, Elevations, and Sections 11.3 Detail Drawings, Keynotes, and Technical Specifications
12 Chapter 12: Basic Rigging: Slings & Hardware
12.1 Rigging Safety Fundamentals, Crane Communication, and ASME Hand Signals 12.2 Rigging Slings: Synthetic, Wire Rope, and Alloy Steel Chain Slings 12.3 Rigging Hardware: Shackles, Eye Bolts, Hooks, and Wire Rope Clips
13 Chapter 13: Basic Rigging: Hitches & Load Dynamics
13.1 Rigging Hitches: Vertical, Choker, and Basket Hitches 13.2 Sling Angle Stress Factors and Load Weight Calculations 13.3 Hoists, Come-Alongs, Chain Falls, and Rigging Inspection Procedures
14 Chapter 14: Communication & Employability in the Trades
14.1 Communication Process, Active Listening, and Job-Site Etiquette 14.2 Reading Trade Documents and Writing Job-Site Reports 14.3 The Construction Industry, Career Pathways, and Professionalism 14.4 Critical Thinking, Planning, Feedback, and Conflict Resolution on the Job Site
15 Chapter 15: Material Handling & Storage
15.1 Manual Material Handling, Ergonomics, and Safe Lifting Procedures 15.2 Material Stacking, Storing, and Job-Site Housekeeping Guidelines 15.3 Non-Motorized Handling Equipment: Carts, Dollies, and Wheelbarrows 15.4 Motorized Handling Equipment Safety and Basic Rigging Knots
1.3 Personal Protective Equipment (PPE) Selection, Inspection, and Maintenance
Key Takeaways Explain This Topic AI
Under 29 CFR 1926.95, employers are legally obligated to provide and pay for almost all required PPE, while employees are responsible for pre-use inspection, correct fit, and proper maintenance.
Eye and face protection certified under ANSI Z87.1 requires high-impact (Z87+) ratings for construction, with face shields serving strictly as secondary protection over primary safety glasses or goggles.
Hard hats certified under ANSI Z89.1 are categorized by impact type (Type I for top only, Type II for top and lateral) and electrical class (Class G for 2,200V, Class E for 20,000V, and Class C for conductive 0V).
Hearing protection with adequate Noise Reduction Ratings (NRR) is mandatory when noise reaches or exceeds the OSHA PEL of 90 dBA (8-hr TWA), with an Action Level of 85 dBA triggering hearing conservation programs.
Respiratory protection requires medical clearance, qualitative or quantitative fit testing, and daily positive/negative user seal checks, with air-purifying respirators prohibited in IDLH or oxygen-deficient environments (<19.5% O2).
Last updated: September 2026
1.3 Personal Protective Equipment (PPE) Selection, Inspection, and Maintenance
When engineering and administrative controls cannot completely eliminate jobsite hazards, Personal Protective Equipment (PPE) serves as the final barrier standing between a craftworker and severe injury or death. Governed primarily by 29 CFR 1926 Subpart E , PPE selection is strictly regulated by American National Standards Institute (ANSI) and ASTM International consensus standards. Every construction professional must master the specific ratings, inspection criteria, and maintenance protocols for all major categories of protective gear.
Regulatory Framework: Employer vs. Employee Obligations
Under federal safety law ( 29 CFR 1926.95 and 1910.132 ), the responsibilities for jobsite PPE are clearly divided between management and craftworkers:
Employer Obligations
Hazard Assessment: The employer must conduct a systematic hazard assessment of the jobsite to determine the physical, environmental, and chemical hazards present, and select certified PPE suited to those specific risks.
Mandatory Employer Payment Rule: Under OSHA's payment standard, employers must provide almost all required PPE at zero cost to employees . This includes hard hats, safety glasses, face shields, hearing protectors, chemical goggles, fall protection harnesses, respirators, rubber boots, and welding leathers.
Permissible Exceptions to Employer Payment: Employers are not required to pay for non-specialty safety-toe protective footwear (standard steel-toe work boots) or prescription safety eyewear, provided the employer permits the worker to wear them off the jobsite, and ordinary weather-related cold/rain apparel.
Comprehensive Training: Employers must train workers on when PPE is necessary, what equipment is required, how to properly don, doff, adjust, and wear it, its operational limitations, and its proper inspection and maintenance.
Employee Responsibilities
Craftworkers have an active legal duty to comply with safety protocols:
Pre-Use Inspection: Inspect every piece of PPE before every shift.
Proper Use: Wear PPE properly according to manufacturer specifications (e.g., wearing hard hats facing forward unless reverse-certified, never rolling down earplugs partially).
Defect Reporting: Immediately remove damaged or defective PPE from service, tag it out, and report it to supervision for replacement.
Sanitation and Storage: Clean and store equipment in clean, dry environments protected from UV sunlight, chemical fumes, and mechanical damage.
Head Protection: ANSI/ISEA Z89.1
Head injuries from falling tools, structural materials, and low-clearance piping account for some of the most debilitating traumas in construction. Hard hats are governed by ANSI/ISEA Z89.1 .
Impact Types
Type I Hard Hats: Designed to attenuate kinetic energy and resist penetration exclusively from vertical impacts to the top of the head (e.g., a dropped spud wrench striking the crown).
Type II Hard Hats: Feature an internal high-density foam liner designed to attenuate impact forces and resist penetration resulting from both top and lateral (side, front, and rear) impacts (e.g., being struck by a swinging steel beam or impacting a wall during a fall arrest event). Type II helmets are increasingly standard on modern construction sites.
Electrical Protection Classes
Class Name Voltage Rating Trade Application
Class G General Tested to 2,200 Volts AC General construction, carpentry, masonry with limited electrical exposure. Reduces risk of contact with low-voltage conductors.
Class E Electrical Tested to 20,000 Volts AC Electricians, linemen, substation technicians. Provides maximum protection against high-voltage electrical shock and burn hazards.
Class C Conductive 0 Volts (No Electrical Protection) Prohibited near energized lines. Often made with aluminum shells or vented plastic for thermal comfort in non-electrical trades.
Suspension System and Inspection Protocols
The suspension system inside a hard hat is an engineered shock absorber. It maintains a critical buffer distance of 1 to 1.25 inches (25 to 32 mm) between the rigid outer shell and the wearer's skull, dissipating impact energy through elongation of the suspension webbing.
Daily Inspection Checklist:
Shell: Flex the shell slightly; check for cracks, deep gouges, dents, or a chalky/faded finish indicating severe ultraviolet (UV) degradation.
Suspension: Check that key tabs click securely into shell slots. Inspect webbing for cuts, fraying, tears, chemical degradation, or broken stitches.
Critical Prohibitions:
NEVER drill holes in a hard hat for ventilation.
NEVER carve, cut, or heat the shell.
NEVER apply solvent-based paints, thinners, or unauthorized metallic decals (solvents attack polymer chains, inducing brittleness; metallic stickers conduct electricity).
NEVER carry objects (cell phones, notebooks, lighters) between the suspension and the shell, as this eliminates the shock-absorbing buffer.
Service Life Guidelines: Industry and manufacturer standards generally recommend replacing the suspension every 12 months and the shell every 3 to 5 years , or IMMEDIATELY following any severe impact event, even if visible surface damage is absent.
Eye and Face Protection: ANSI/ISEA Z87.1
Over 2,000 workplace eye injuries occur daily in the U.S., with chipping, grinding, masonry drilling, and chemical handling accounting for the vast majority. Eye and face equipment is regulated by ANSI/ISEA Z87.1 .
Impact Ratings: Basic vs. High-Impact
Z87 (Basic Impact): Tested against a 1-inch steel ball dropped from 50 inches. Prohibited for high-hazard construction operations.
Z87+ (High-Impact Certified): Undergoes ballistic impact testing. Lenses and frames must resist a 1/4-inch steel ball traveling at 150 feet per second (fps) for safety glasses, and 250 fps for safety goggles. All safety glasses used in construction must bear the "Z87+" permanent stamp.
Equipment Types and Application Hierarchy
Safety Glasses with Side Shields: Plano or prescription frames with impact-resistant polycarbonate lenses and permanent side protection. Protect against frontal and peripheral flying chips, wood splinters, and coarse dust.
Safety Goggles: Form a continuous, protective seal around the orbital socket.
Direct Vent: Protects against heavy impact and large debris (rough demolition).
Indirect Vent: Employs hooded baffles that allow air exchange while blocking liquid paths. Mandatory for chemical splashes, concrete slurry, and acid handling.
Non-Vented: Completely sealed against fine vapors and toxic gases.
Face Shields (CRITICAL TRADE RULE): A face shield consists of a transparent polycarbonate or wire-mesh visor extending from the eyebrows to below the chin. A face shield is legally classified as SECONDARY protection only. A face shield must ALWAYS be worn over primary eye protection (Z87+ safety glasses or goggles) . A face shield alone will not prevent projectiles from deflecting underneath the visor into the eyes.
Welding Helmets and Filter Lens Shades ( 29 CFR 1926.102 ): Welding arcs produce intense ultraviolet (UV) and infrared (IR) radiation capable of inflicting permanent retinal burns and "welder's flash" (photokeratitis). Filter lenses are rated by shade numbers:
- Process / Trade Operation Recommended Minimum Filter Lens Shade
- Torch Brazing & Soldering Shade 3 to 4
- Oxyfuel Gas Cutting / Light Welding Shade 4 to 5
- Shielded Metal Arc Welding (SMAW/Stick) — up to 5/32" electrode Shade 9 to 10
- SMAW / Stick — 5/32" to 1/4" electrode Shade 10 to 12
- GMAW (MIG) & GTAW (TIG) Welding Shade 11 to 14
- Air Carbon Arc Gouging / Plasma Arc Cutting (heavy) Shade 12 to 14
- Hearing Protection: OSHA 29 CFR 1926.52 and NRR
Occupational noise-induced hearing loss (NIHL) is permanent and irreversible. In construction, equipment like jackhammers (110 dBA), chop saws (105 dBA), and powder-actuated tools (140 dBA) cause progressive damage to auditory hair cells.
OSHA Noise Standards and the 5-dBA Exchange Rate
Permissible Exposure Limit (PEL): 90 dBA for an 8-hour Time-Weighted Average (TWA).
Action Level: 85 dBA 8-hour TWA. Exceeding 85 dBA mandates an OSHA Hearing Conservation Program , including baseline and annual audiograms, free hearing protectors, and annual training.
Rule of Thumb: If you must shout to be clearly understood by someone an arm's length away (~3 feet), noise levels exceed 85 dBA and hearing protection is required.
The 5-dBA Exchange Rate: Under OSHA standard 1926.52 , every 5-dBA increase in sound level cuts the allowable unprotected exposure duration by half:
- Sound Level (dBA) Maximum Permissible Daily Exposure (Unprotected)
- 90 dBA 8 hours
- 95 dBA 4 hours
- 100 dBA 2 hours
- 105 dBA 1 hour
- 110 dBA 30 minutes
- 115 dBA 15 minutes (Maximum allowable continuous noise without protection)
- 140 dBC Ceiling limit for impulse or impact peak noise (no exposure permitted)
- Noise Reduction Rating (NRR) and OSHA Field Derating
Hearing protectors are labeled with an EPA Noise Reduction Rating (NRR) established in idealized laboratory settings. Because real-world jobsite fit and compliance differ drastically from laboratories, OSHA applies a field derating formula when evaluating whether protector attenuation brings worker exposure below the 90 dBA PEL: Estimated Jobsite Exposure (dBA) = Noise Level (dBA) − [ NRR − 7 2 ] \text{Estimated Jobsite Exposure (dBA)} = \text{Noise Level (dBA)} - \left[ \frac{\text{NRR} - 7}{2} \right] Estimated Jobsite Exposure (dBA) = Noise Level (dBA) − [ 2 NRR − 7 ]
Calculation Example: A pipefitter operates an abrasive chop saw in a 100 dBA environment wearing foam earplugs labeled with an NRR of 29 :
Estimated Exposure = 100 − [ 29 − 7 2 ] = 100 − 11 = 89 dBA \text{Estimated Exposure} = 100 - \left[ \frac{29 - 7}{2} \right] = 100 - 11 = 89\text{ dBA} Estimated Exposure = 100 − [ 2 29 − 7 ] = 100 − 11 = 89 dBA
The derated reduction is 11 dBA, bringing effective exposure to 89 dBA, which meets OSHA's 90 dBA PEL.
Dual Protection: When noise levels exceed 105 dBA , workers must wear dual hearing protection (earplugs worn simultaneously under earmuffs). Dual protection does not double the NRR; it adds approximately 5 dB of additional attenuation to the higher-rated device.
Respiratory Protection: 29 CFR 1926.103 and 1910.134
Construction craftworkers face diverse respiratory hazards, including respirable crystalline silica (masonry/concrete), lead dust (paint removal), toxic welding fumes, and organic solvent vapors. All respiratory protection must comply with 29 CFR 1910.134 .
- Respirator Classifications RESPIRATOR SYSTEMS
- │
- ┌──────────────────────────┴──────────────────────────┐
- ▼ ▼
- AIR-PURIFYING RESPIRATORS (APR) ATMOSPHERE-SUPPLYING RESPIRATORS
- Cleans ambient jobsite air • Provides clean, independent air
- Filtering Facepiece (N95/P100) • Supplied-Air Respirator (SAR - Airline)
- Half-Mask Elastomeric (APF = 10) • Self-Contained Breathing Apparatus
- Full-Face Elastomeric (APF = 50) (SCBA - APF = 10,000)
- Powered APR (PAPR - APF = 25-1000) ★ MANDATORY for <19.5% O2 or IDLH
- ★ PROHIBITED in Oxygen Deficient / IDLH
Assigned Protection Factor (APF): The workplace level of respiratory protection a properly fitted respirator or class of respirators is expected to provide. An APF of 10 means the device safely reduces exposure in concentrations up to 10 times the OSHA PEL.
CRITICAL LIFE SAFETY RULE: Air-purifying respirators (APRs) do NOT supply oxygen; they merely filter ambient air. APRs are strictly forbidden in oxygen-deficient atmospheres (<19.5% O2) or atmospheres that are Immediately Dangerous to Life or Health (IDLH). In these spaces, workers must wear an atmosphere-supplying respirator (an SCBA or a positive-pressure SAR with an auxiliary escape cylinder).
Mandatory Respiratory Program Requirements
Medical Clearance: Before fit testing or wearing a negative-pressure respirator, the worker must be evaluated by a Physician or Licensed Health Care Professional (PLHCP) using the OSHA Medical Questionnaire ( Appendix C of 1910.134 ). The evaluation ensures the worker's heart and lungs can bear the physical stress of breathing resistance.
Annual Fit Testing: Required annually for all tight-fitting facepieces.
Qualitative Fit Test (QLFT): Pass/fail test using taste or smell agents (Bitrex, saccharin, isoamyl acetate, irritant smoke).
Quantitative Fit Test (QNFT): Computerized instrument (Portacount) measures particle concentration inside the mask versus outside to calculate a numerical Fit Factor.
Clean-Shaven Mandate: Facial hair that lies along the sealing surface of the respirator facepiece (beards, goatees, stubble) is strictly prohibited . Hair prevents a tight facial seal, allowing contaminants to bypass the filter.
User Seal Checks (Mandatory Every Time Donned):
Positive-Pressure Check: Block the exhalation valve with the palm of the hand and exhale gently. The facepiece should bulge slightly outward with no outward air leaks around the perimeter.
Negative-Pressure Check: Cover the inhalation filter inlets or cartridges with the palms and inhale gently. The facepiece should collapse slightly inward toward the face and remain collapsed for 10 seconds without leaking.
- Foot, Hand, and High-Visibility Protection
- Foot Protection: ASTM F2413
Safety footwear must comply with ASTM F2413 (formerly ANSI Z41):
Impact (I/75) & Compression (C/75): Withstands a 75 foot-pound drop impact and a 2,500-pound compression load across the toe box.
Steel vs. Composite Toes: Steel toes provide maximum impact resistance; composite toes (fiberglass, carbon fiber) provide non-conductive, non-magnetic, lighter protection that offers superior thermal insulation in extreme temperatures.
Metatarsal Guards (Mt/75): Guards extending upward from the toe box over the instep (metatarsal bones), shielding the top of the foot from falling heavy pipe, structural plate, and tampers.
Puncture Resistance (PR): A steel or Kevlar midsole plate that withstands at least 270 pounds (1,200 N) of puncture force, preventing discarded framing nails and sharp rebar scraps from penetrating the sole.
Electrical Hazard (EH): Soles formulated to withstand 18,000 volts at 60 Hz for 1 minute under dry conditions with zero current leakage exceeding 1.0 mA.
Hand Protection: ANSI/ISEA 105
Hands suffer more injuries than any other extremity. Gloves are rated under ANSI/ISEA 105 :
Cut Resistance Levels (A1 to A9): Measures grams of weight required for a razor blade to cut through the material using a 20mm stroke (ASTM F2992-15):
Level A1 (200-499g): General light material handling, small parts.
Level A4 (1,500-2,199g): Sheet metal fabrication, metal framing, HVAC duct handling.
Level A9 (6,000+g): Heavy glass handling, metal recycling, sharp scrap demolition.
Chemical Resistance: Never choose chemical gloves arbitrarily. Always consult Section 8 (Exposure Controls/Personal Protection) of the Safety Data Sheet (SDS) . Nitrile resists petroleum solvents and oils; Neoprene resists acids and caustics; Butyl rubber resists highly toxic ketones and gases.
Anti-Vibration Gloves (ISO 10819): Attenuate high-frequency vibration to protect workers from Hand-Arm Vibration Syndrome (HAVS) and Vibration White Finger when running jackhammers, demolition tools, and tampers.
High-Visibility Safety Apparel: ANSI/ISEA 107
High-visibility apparel ensures craftworkers are visually conspicuous to heavy equipment operators and motorists, regulated under ANSI/ISEA 107 :
Performance Class Minimum Background Material Minimum Retroreflective Tape Recommended Jobsite Environment
Class 1 217 sq. inches 155 sq. inches Off-road environments, warehouse logistics, parking lots where vehicle traffic travels under 25 mph.
Class 2 775 sq. inches 201 sq. inches Standard construction jobsites, utility work, roadway work where vehicle speeds range from 25 to 50 mph in daylight or inclement weather.
Class 3 1,240 sq. inches 310 sq. inches High-speed highways (>50 mph), extreme darkness, flaggers, emergency response. Requires full sleeves with retroreflective bands so the human form is recognizable in 360 degrees. (Pairing a Class 2 vest with Class E pants creates an ensemble certified as Class 3).
Master Construction PPE Specification and Inspection Guide
PPE Category Standard Critical Rating / Class Pre-Use Inspection Checkpoints Service Life / Replacement Triggers
Head Protection ANSI/ISEA Z89.1 Type I (top), Type II (top/lateral); Class E (20 kV), Class G (2.2 kV), Class C (0 V). Check shell for micro-cracks, gouges, UV chalking; verify suspension clips; ensure 1-1.25" buffer. Suspension: 12 months; Shell: 3-5 years; replace immediately upon any severe impact.
Eye & Face ANSI/ISEA Z87.1 Z87+ (High Impact); Shades 3-14 for welding; Face shields (Secondary only). Check lenses for scratches, pits, cracks; verify frame integrity; inspect side shield retention. Replace scratched lenses immediately; replace shields showing cloudiness or deformation.
Hearing 29 CFR 1926.52 NRR (Field derating: [NRR-7]/2 ); PEL = 90 dBA; Action Level = 85 dBA. Check earmuff cushions for stiffening, cracks, tears; ensure foam plugs are clean and pliable. Discard single-use foam plugs after each shift; replace earmuff cushions semi-annually.
Respiratory 29 CFR 1910.134 APR (APF 10-50); SCBA (APF 10,000); N95/P100; Medical clearance & fit test. Perform positive/negative user seal checks; inspect exhalation valve, straps, facepiece cracks. Replace filters when breathing resistance increases or soiled; replace damaged valves immediately.
Foot Protection ASTM F2413 I/75 C/75; Metatarsal (Mt/75); Puncture (PR 270 lbs); Electrical (EH 18 kV). Check for exposed steel/composite toe cap, sole tread wear, puncture marks, oil degradation. Replace footwear when protective cap becomes exposed, sole punctures, or tread separates.
Hand Protection ANSI/ISEA 105 Cut Levels A1-A9; Chemical compatibility per SDS Sec 8; Anti-vibration (ISO 10819). Inspect for tears, punctures, seam fraying, chemical degradation (swelling, cracking, stiffness). Discard gloves immediately if cut, chemical breakthrough occurs, or seams split.
High-Visibility ANSI/ISEA 107 Class 1 (<25 mph), Class 2 (25-50 mph), Class 3 (>50 mph / nighttime). Check retroreflective tape for cracking, peeling; verify background fabric is clean and fluorescent. Replace garments when fluorescent background is heavily soiled or reflective tape degrades.