Study guide

5.1 Linear Measurement, Reading Imperial and Metric Rules, and Unit Conversions

NCCER Core Curriculum: Introductory Craft Skills Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Basic Safety Fundamentals & OSHA Regulations

1.1 Safety Culture, Incident Costs, and OSHA Regulations 1.2 Hazard Recognition, Job Safety Analysis (JSA), and the Hierarchy of Controls 1.3 Personal Protective Equipment (PPE) Selection, Inspection, and Maintenance

2 Chapter 2: Elevated Work, Scaffolding & Electrical Safety

2.1 Fall Protection Systems: Guardrails, Safety Nets, and Personal Fall Arrest Systems (PFAS) 2.2 Ladder Safety Standards and Scaffolding Requirements 2.3 Electrical Hazards, Ground Fault Protection (GFCI), and Lockout/Tagout (LOTO)

3 Chapter 3: Health Hazards, Fire Protection & Chemical Safety

3.1 Confined Space Entry, Trenching, and Excavation Safety 3.2 Fire Protection, Extinguisher Classifications, and Job-Site Fire Prevention 3.3 Hazard Communication (HazCom), GHS Pictograms, and Safety Data Sheets (SDS)

4 Chapter 4: Trade Mathematics: Arithmetic & Fractions

4.1 Whole Number Operations and Trade Estimations 4.2 Fraction Arithmetic, Common Denominators, and Tape Measure Calculations 4.3 Decimal Operations and Conversions Between Fractions, Decimals, and Percentages

5 Chapter 5: Trade Mathematics: Geometry & Measurement

5.1 Linear Measurement, Reading Imperial and Metric Rules, and Unit Conversions 5.2 Area and Perimeter Calculations for Craft Layouts 5.3 Volume Calculations and Concrete/Material Estimations 5.4 Right Triangles, Angles, and the Pythagorean Theorem (3-4-5 Rule)

6 Chapter 6: Hand Tools: Striking, Fastening & Holding

6.1 Striking Tools and Demolition/Prying Equipment 6.2 Screwdrivers, Wrenches, Sockets, and Torque Wrenches 6.3 Pliers, Clamps, and Vises in Construction

7 Chapter 7: Hand Tools: Cutting, Shaping & Layout

7.1 Handsaws, Hacksaws, Chisels, Files, Knives, and Digging Tools 7.2 Levels, Plumb Bobs, and Chalk Lines 7.3 Framing Squares, Speed Squares, and Layout Procedures

8 Chapter 8: Power Tools: Drills, Saws & Power Sources

8.1 Power Tool Safety Principles, Power Sources, and Electrical Protection 8.2 Electric Drills, Hammer Drills, Rotary Hammers, and Impact Drivers 8.3 Power Saws: Circular, Reciprocating, Jigsaw, Band, Table, and Miter Saws

9 Chapter 9: Power Tools: Grinders, Pneumatic & Fastening Tools

9.1 Angle Grinders, Bench Grinders, Cut-Off Saws, and Oscillating Multi-Tools 9.2 Pneumatic Tools, Air Compressors, and Hose Safety 9.3 Powder-Actuated Fastening Systems and Hydraulic Tools

10 Chapter 10: Construction Drawings: Fundamentals & Line Types

10.1 Components of Construction Drawings: Title Blocks, Revision Blocks, and Legends 10.2 Types of Construction Drawings: Civil, Architectural, Structural, and MEP Plans 10.3 The Alphabet of Lines, Symbols, and Drawing Abbreviations

11 Chapter 11: Construction Drawings: Scales & Plan Views

11.1 Reading Architect's and Engineer's Scales 11.2 Plan Views, Elevations, and Sections 11.3 Detail Drawings, Keynotes, and Technical Specifications

12 Chapter 12: Basic Rigging: Slings & Hardware

12.1 Rigging Safety Fundamentals, Crane Communication, and ASME Hand Signals 12.2 Rigging Slings: Synthetic, Wire Rope, and Alloy Steel Chain Slings 12.3 Rigging Hardware: Shackles, Eye Bolts, Hooks, and Wire Rope Clips

13 Chapter 13: Basic Rigging: Hitches & Load Dynamics

13.1 Rigging Hitches: Vertical, Choker, and Basket Hitches 13.2 Sling Angle Stress Factors and Load Weight Calculations 13.3 Hoists, Come-Alongs, Chain Falls, and Rigging Inspection Procedures

14 Chapter 14: Communication & Employability in the Trades

14.1 Communication Process, Active Listening, and Job-Site Etiquette 14.2 Reading Trade Documents and Writing Job-Site Reports 14.3 The Construction Industry, Career Pathways, and Professionalism 14.4 Critical Thinking, Planning, Feedback, and Conflict Resolution on the Job Site

15 Chapter 15: Material Handling & Storage

15.1 Manual Material Handling, Ergonomics, and Safe Lifting Procedures 15.2 Material Stacking, Storing, and Job-Site Housekeeping Guidelines 15.3 Non-Motorized Handling Equipment: Carts, Dollies, and Wheelbarrows 15.4 Motorized Handling Equipment Safety and Basic Rigging Knots

5.1 Linear Measurement, Reading Imperial and Metric Rules, and Unit Conversions

Key Takeaways Explain This Topic AI

Imperial linear measurement relies on base-12 subdivisions (inches, feet, yards, miles), requiring craftworkers to navigate fractional increments down to 1/16" or 1/32" on standard tape measures.

The International System of Units (SI / Metric) operates on a base-10 decimal hierarchy, utilizing millimeters (mm) for precision trade fabrication, centimeters (cm) for general dimensions, and meters (m) for structural spans.

Converting between Imperial and Metric systems demands precision factors: exactly 25.4 mm (or 2.54 cm) per inch, 0.3048 m per foot, and 3.281 feet (or 39.37 inches) per meter to avoid compounding layout errors.

Temperature conversions between Fahrenheit and Celsius follow fixed thermodynamic formulas: C = (F - 32) × 5/9 and F = (C × 9/5) + 32, with reference benchmarks at freezing (32°F / 0°C) and boiling (212°F / 100°C).

Liquid volume and weight conversions require distinguishing between short tons (2,000 lbs) and metric tonnes (1,000 kg / 2,204.6 lbs), as well as fluid measurements (16 fl oz per pint, 2 pints per quart, 4 quarts per gallon).

Last updated: September 2026

5.1 Linear Measurement, Reading Imperial and Metric Rules, and Unit Conversions

Precision measurement is the fundamental currency of the construction crafts. Whether laying out commercial building footings, roughing in mechanical piping, pulling electrical feeder circuits, or fabricating architectural casework, craftworkers must take, communicate, and convert measurements with flawless accuracy. A misread measurement or calculation error does not simply waste material—it cascades across multiple trades, causing rework, schedule delays, structural defects, and severe financial losses.

Modern construction jobsites in North America operate primarily on the US Customary (Imperial) measurement system, but increasingly interface with the Metric System (International System of Units, or SI) due to global equipment manufacturing, international architectural design firms, and federal construction mandates. Mastery of both systems and their conversion mathematics is a non-negotiable professional trade competency.

The Imperial (US Customary) System of Linear Measurement

The Imperial system measures linear distance using four primary units:

Inches (in. or ") : The primary base unit for fine layout, material sizing, framing lumber dimensions, pipe diameters, and mechanical fittings.

Feet (ft. or ') : The standard unit for architectural dimensions, room dimensions, building elevations, and structural member spans ( 1 ft = 12 in 1\text{ ft} = 12\text{ in} 1 ft = 12 in ).

Yards (yd.) : Used primarily for site excavation distances, concrete placement volumes, fencing runs, and carpet/turf takeoffs ( 1 yd = 3 ft = 36 in 1\text{ yd} = 3\text{ ft} = 36\text{ in} 1 yd = 3 ft = 36 in ).

Miles (mi.) : Used in civil highway construction, pipeline rights-of-way, and large-scale infrastructure projects ( 1 mi = 5 , 280 ft = 1 , 760 yd 1\text{ mi} = 5,280\text{ ft} = 1,760\text{ yd} 1 mi = 5 , 280 ft = 1 , 760 yd ).

Linear Imperial Equivalencies 1 foot (’) = 12 inches (") 1\text{ foot (')} = 12\text{ inches (")} 1 foot (’) = 12 inches (") 1 yard (yd) = 3 feet = 36 inches 1\text{ yard (yd)} = 3\text{ feet} = 36\text{ inches} 1 yard (yd) = 3 feet = 36 inches 1 mile (mi) = 5 , 280 feet = 1 , 760 yards 1\text{ mile (mi)} = 5,280\text{ feet} = 1,760\text{ yards} 1 mile (mi) = 5 , 280 feet = 1 , 760 yards

Reading the Imperial Tape Measure

A standard carpenter's tape measure subdivides each inch into binary fractions. The length of the graduation line on the blade directly signifies the fraction's denominator: | | | | | | | | | | | | | | | | |

  • | | | | | 1/4" Mark
  • | | | 1/2" Mark
  • | | 1" Full Mark
  • 0 1/8 1/4 3/8 1/2 5/8 3/4 7/8 1"
  • 1/16 3/16 5/16 7/16 9/16 11/16 13/16 15/16

1-inch marks: The longest lines running completely or nearly across the tape blade, accompanied by bold whole numbers.

1/2-inch marks: The second-longest graduation lines, centered exactly midway between inch marks.

1/4-inch marks: The third-longest lines, dividing the inch into four equal quarters ( 1 / 4 " , 2 / 4 " = 1 / 2 " , 3 / 4 " , 4 / 4 " = 1 " 1/4", 2/4" = 1/2", 3/4", 4/4" = 1" 1/4" , 2/4" = 1/2" , 3/4" , 4/4" = 1" ).

1/8-inch marks: Intermediate lines dividing each quarter in half ( 1 / 8 " , 3 / 8 " , 5 / 8 " , 7 / 8 " 1/8", 3/8", 5/8", 7/8" 1/8" , 3/8" , 5/8" , 7/8" ).

1/16-inch marks: The shortest common marks on standard trade tapes, dividing the inch into 16 discrete increments.

Special Tape Features: Most trade tapes feature red stud markings every 16 inches (the standard on-center spacing for wall studs, floor joists, and roof rafters) and black diamond truss markings every 19.2 inches (an engineered layout spacing allowing five structural modules across an 8-foot sheet good).

Trade Caution: The "True-Zero" Floating Hook The metal hook at the end of every tape measure is deliberately loose, sliding back and forth on rivets by approximately 1 / 16 1/16 1/16 inch (the exact thickness of the hook blade). When pulling an outside measurement (hooked over the end of a board), the hook slides out to include its own thickness. When pushing an inside measurement (butted against an inside corner or wall), the hook compresses inward to eliminate its own thickness. Never hammer or crimp the rivets tight —doing so permanently destroys the tape's accuracy on either inside or outside readings!

Compound Imperial Dimensions and Unit Conversions

Architectural drawings rarely present dimensions purely in inches or purely in decimal feet. Instead, blueprint dimensions are written as compound measurements combining feet, inches, and fractions (e.g., 14 ′ - 8 3 / 8 " 14'\text{ - }8\text{ }3/8" 1 4 ′ - 8 3/8" ). Craftworkers must convert compound dimensions into total inches for shop fabrication or into decimal feet for electronic layout tools and calculators.

Converting Compound Dimensions to Total Inches

To convert a dimension of feet, inches, and fractions into total inches:

Multiply the number of feet by 12 12 12 .

Add the whole inches.

Convert the fraction to a decimal or add the fractional numerator over the common denominator. Total Inches = ( Feet × 12 ) + Inches + Fraction \text{Total Inches} = (\text{Feet} \times 12) + \text{Inches} + \text{Fraction} Total Inches = ( Feet × 12 ) + Inches + Fraction

Worked Example: Convert 14 ′ - 8 3 / 8 " 14'\text{ - }8\text{ }3/8" 1 4 ′ - 8 3/8" into total decimal inches.

Convert feet to inches: 14 ft × 12 in/ft = 168 inches 14\text{ ft} \times 12\text{ in/ft} = 168\text{ inches} 14 ft × 12 in/ft = 168 inches .

Add the whole inches: 168 + 8 = 176 inches 168 + 8 = 176\text{ inches} 168 + 8 = 176 inches .

Convert the fraction: 3 / 8 " = 3 ÷ 8 = 0.375 inches 3/8" = 3 \div 8 = 0.375\text{ inches} 3/8" = 3 ÷ 8 = 0.375 inches .

Total dimension: 176 + 0.375 = 176.375 inches 176 + 0.375 = 176.375\text{ inches} 176 + 0.375 = 176.375 inches (or 176 3 / 8 " 176\text{ }3/8" 176 3/8" ).

Converting Compound Dimensions to Decimal Feet

When calculating area or volume, all dimensions must share identical units. To convert compound measurements into decimal feet: Decimal Feet = Feet + ( Inches + Fraction 12 ) \text{Decimal Feet} = \text{Feet} + \left(\frac{\text{Inches} + \text{Fraction}}{12}\right) Decimal Feet = Feet + ( 12 Inches + Fraction ​ )

Worked Example: Convert 26 ′ - 9 1 / 2 " 26'\text{ - }9\text{ }1/2" 2 6 ′ - 9 1/2" into decimal feet.

Convert the inches and fraction into decimal inches: 9 1 / 2 " = 9.5 inches 9\text{ }1/2" = 9.5\text{ inches} 9 1/2" = 9.5 inches .

Divide decimal inches by 12 12 12 : 9.5 ÷ 12 = 0.7917 feet 9.5 \div 12 = 0.7917\text{ feet} 9.5 ÷ 12 = 0.7917 feet .

Combine with whole feet: 26 + 0.7917 = 26.7917 feet 26 + 0.7917 = 26.7917\text{ feet} 26 + 0.7917 = 26.7917 feet .

Converting Decimal Feet Back to Feet, Inches, and Fractions

Calculators output decimal feet (e.g., 18.72 ft 18.72\text{ ft} 18.72 ft ). A carpenter cannot find ".72 feet" on a tape measure. The field conversion process is:

Retain the whole number as feet : 18 feet 18\text{ feet} 18 feet .

Multiply the remaining decimal by 12 12 12 to find whole inches: 0.72 × 12 = 8.64 inches ⟹ 8 whole inches 0.72 \times 12 = 8.64\text{ inches} \implies 8\text{ whole inches} 0.72 × 12 = 8.64 inches ⟹ 8 whole inches

Multiply the remaining decimal fraction by 16 16 16 to find sixteenths of an inch: 0.64 × 16 = 10.24 ≈ 10 sixteenths 0.64 \times 16 = 10.24 \approx 10\text{ sixteenths} 0.64 × 16 = 10.24 ≈ 10 sixteenths

Reduce the fraction to lowest terms: 10 / 16 " = 5 / 8 " 10/16" = 5/8" 10/16" = 5/8" .

The final tape measure reading is 18 ′ - 8 5 / 8 " 18'\text{ - }8\text{ }5/8" 1 8 ′ - 8 5/8" .

The Metric System (SI) in Construction

The International System of Units (SI) is a base-10 decimal measurement system. Because every unit change involves powers of 10, calculations eliminate complex fractional denominators.

Metric Prefixes and Scale Factors

  • Prefix Symbol Multiplication Factor Scientific Value
  • Kilo- k \text{k} k 1 , 000 1,000 1 , 000 10 3 10^3 1 0 3
  • Hecto- h \text{h} h 100 100 100 10 2 10^2 1 0 2
  • Deka- da \text{da} da 10 10 10 10 1 10^1 1 0 1
  • [Base Unit] — 1 1 1 (meter, liter, gram) 10 0 10^0 1 0 0
  • Deci- d \text{d} d 0.1 0.1 0.1 ( 1 / 10 1/10 1/10 ) 10 − 1 10^{-1} 1 0 − 1
  • Centi- c \text{c} c 0.01 0.01 0.01 ( 1 / 100 1/100 1/100 ) 10 − 2 10^{-2} 1 0 − 2
  • Milli- m \text{m} m 0.001 0.001 0.001 ( 1 / 1 , 000 1/1,000 1/1 , 000 ) 10 − 3 10^{-3} 1 0 − 3

Metric Linear Units and Trade Usage 1 kilometer (km) = 1 , 000 meters 1\text{ kilometer (km)} = 1,000\text{ meters} 1 kilometer (km) = 1 , 000 meters 1 meter (m) = 100 centimeters = 1 , 000 millimeters 1\text{ meter (m)} = 100\text{ centimeters} = 1,000\text{ millimeters} 1 meter (m) = 100 centimeters = 1 , 000 millimeters 1 centimeter (cm) = 10 millimeters (mm) 1\text{ centimeter (cm)} = 10\text{ millimeters (mm)} 1 centimeter (cm) = 10 millimeters (mm)

Crucial Trade Practice: Millimeters vs. Centimeters On metric architectural and mechanical drawings, dimensions are almost universally expressed in millimeters (mm) or meters (m) , rarely in centimeters (cm). Millimeters provide sufficient precision for metal fabrication, rough framing, and cabinetry without requiring decimal points (e.g., 2 , 400 mm 2,400\text{ mm} 2 , 400 mm instead of 240.0 cm 240.0\text{ cm} 240.0 cm ). On civil site plans, distances and elevations are expressed in decimal meters (e.g., 125.45 m 125.45\text{ m} 125.45 m ). Centimeters are avoided because a missed decimal point on a soiled shop drawing converts a 10 cm 10\text{ cm} 10 cm piece into 100 mm 100\text{ mm} 100 mm or 1 mm 1\text{ mm} 1 mm , leading to severe fabrication errors.

Cross-System Conversions (Imperial vs. Metric)

When working on international projects or installing imported industrial equipment, craftworkers must convert between Imperial and Metric measurements. memorizing standard conversion factors prevents layout errors.

Fundamental Conversion Constants

Unit to Convert Multiplication Factor Equivalent Result

1 inch × 25.4 mm \times 25.4\text{ mm} × 25.4 mm (exact legal standard) 25.4 millimeters 25.4\text{ millimeters} 25.4 millimeters

  • 1 inch × 2.54 cm \times 2.54\text{ cm} × 2.54 cm 2.54 centimeters 2.54\text{ centimeters} 2.54 centimeters
  • 1 foot × 0.3048 m \times 0.3048\text{ m} × 0.3048 m (exact) 0.3048 meters 0.3048\text{ meters} 0.3048 meters

1 foot × 304.8 mm \times 304.8\text{ mm} × 304.8 mm 304.8 millimeters 304.8\text{ millimeters} 304.8 millimeters

1 yard × 0.9144 m \times 0.9144\text{ m} × 0.9144 m 0.9144 meters 0.9144\text{ meters} 0.9144 meters

1 mile × 1.60934 km \times 1.60934\text{ km} × 1.60934 km 1.609 kilometers 1.609\text{ kilometers} 1.609 kilometers

1 millimeter × 0.03937 in \times 0.03937\text{ in} × 0.03937 in 0.03937 inches 0.03937\text{ inches} 0.03937 inches

  • 1 centimeter × 0.3937 in \times 0.3937\text{ in} × 0.3937 in 0.3937 inches 0.3937\text{ inches} 0.3937 inches
  • 1 meter × 39.37 in \times 39.37\text{ in} × 39.37 in 39.37 inches 39.37\text{ inches} 39.37 inches

1 meter × 3.28084 ft \times 3.28084\text{ ft} × 3.28084 ft (approx. 3.281 ft 3.281\text{ ft} 3.281 ft ) 3.281 feet 3.281\text{ feet} 3.281 feet

1 kilometer × 0.62137 mi \times 0.62137\text{ mi} × 0.62137 mi 0.621 miles 0.621\text{ miles} 0.621 miles

Worked Example: An imported CNC milling machine base requires an anchor bolt pattern spaced 1 , 850 mm 1,850\text{ mm} 1 , 850 mm apart. What is this center-to-center distance in inches and feet?

Convert millimeters to inches: 1 , 850 mm ÷ 25.4 mm/in = 72.8346 inches 1,850\text{ mm} \div 25.4\text{ mm/in} = 72.8346\text{ inches} 1 , 850 mm ÷ 25.4 mm/in = 72.8346 inches .

Convert to feet and inches: 72.8346 ÷ 12 = 6.0695 feet ⟹ 6 whole feet 72.8346 \div 12 = 6.0695\text{ feet} \implies 6\text{ whole feet} 72.8346 ÷ 12 = 6.0695 feet ⟹ 6 whole feet .

Remaining inches: 72.8346 − ( 6 × 12 ) = 0.8346 inches 72.8346 - (6 \times 12) = 0.8346\text{ inches} 72.8346 − ( 6 × 12 ) = 0.8346 inches .

Convert decimal inches to sixteenths: 0.8346 × 16 = 13.35 ≈ 13 / 16 " 0.8346 \times 16 = 13.35 \approx 13/16" 0.8346 × 16 = 13.35 ≈ 13/16" .

The anchor spacing layout is 6 ′ - 0 13 / 16 " 6'\text{ - }0\text{ }13/16" 6 ′ - 0 13/16" (or 72 13 / 16 " 72\text{ }13/16" 72 13/16" ).

Temperature Conversions in Construction

Temperature monitoring is critical across multiple building trades:

Concrete Placement (ACI 306R/305R): Fresh concrete must not freeze before reaching 500 psi compressive strength. Cold-weather placement protocols engage when temperatures drop below 40 ∘ F 40^\circ\text{F} 4 0 ∘ F ( 4.4 ∘ C 4.4^\circ\text{C} 4. 4 ∘ C ).

Asphalt Paving: Bituminous asphalt must be rolled and compacted while mix temperatures exceed 175 ∘ F 175^\circ\text{F} 17 5 ∘ F to 225 ∘ F 225^\circ\text{F} 22 5 ∘ F .

HVAC & Refrigeration: Psychrometrics, refrigerant boiling points, and thermostat calibrations require continuous translation between Fahrenheit and Celsius.

Thermodynamic Conversion Formulas Celsius to Fahrenheit: F = ( C × 9 5 ) + 32 or F = ( C × 1.8 ) + 32 \text{Celsius to Fahrenheit: } F = \left(C \times \frac{9}{5}\right) + 32 \quad \text{or} \quad F = (C \times 1.8) + 32 Celsius to Fahrenheit: F = ( C × 5 9 ​ ) + 32 or F = ( C × 1.8 ) + 32 Fahrenheit to Celsius: C = ( F − 32 ) × 5 9 or C = F − 32 1.8 \text{Fahrenheit to Celsius: } C = (F - 32) \times \frac{5}{9} \quad \text{or} \quad C = \frac{F - 32}{1.8} Fahrenheit to Celsius: C = ( F − 32 ) × 9 5 ​ or C = 1.8 F − 32 ​

Critical Temperature Benchmarks

  • Temperature Event Fahrenheit ( ∘ F ^\circ\text{F} ∘ F ) Celsius ( ∘ C ^\circ\text{C} ∘ C )
  • Water Freezing Point 32 ∘ F 32^\circ\text{F} 3 2 ∘ F 0 ∘ C 0^\circ\text{C} 0 ∘ C
  • Cold-Weather Concrete Threshold 40 ∘ F 40^\circ\text{F} 4 0 ∘ F 4.4 ∘ C 4.4^\circ\text{C} 4. 4 ∘ C

Standard Room Temperature 68 ∘ F − 72 ∘ F 68^\circ\text{F} - 72^\circ\text{F} 6 8 ∘ F − 7 2 ∘ F 20 ∘ C − 22.2 ∘ C 20^\circ\text{C} - 22.2^\circ\text{C} 2 0 ∘ C − 22. 2 ∘ C

  • Human Body Temperature 98.6 ∘ F 98.6^\circ\text{F} 98. 6 ∘ F 37 ∘ C 37^\circ\text{C} 3 7 ∘ C
  • Water Boiling Point (Sea Level) 212 ∘ F 212^\circ\text{F} 21 2 ∘ F 100 ∘ C 100^\circ\text{C} 10 0 ∘ C

Worked Example: A high-performance European epoxy flooring adhesive specifies an application temperature of 22 ∘ C 22^\circ\text{C} 2 2 ∘ C . What is the jobsite ambient temperature required in degrees Fahrenheit?

F = ( 22 × 1.8 ) + 32 = 39.6 + 32 = 71.6 ∘ F F = (22 \times 1.8) + 32 = 39.6 + 32 = 71.6^\circ\text{F} F = ( 22 × 1.8 ) + 32 = 39.6 + 32 = 71. 6 ∘ F

Weight and Liquid Volume Conversions

Trade mathematics encompasses weight and liquid measurement for rigging capacities, structural dead loads, equipment hauling, paint estimation, and hydraulic systems.

Weight and Mass Equivalencies

Ounces and Pounds: 16 ounces (oz) = 1 pound (lb) 16\text{ ounces (oz)} = 1\text{ pound (lb)} 16 ounces (oz) = 1 pound (lb) .

Short Ton (US Customary): 1 short ton = 2 , 000 lbs 1\text{ short ton} = 2,000\text{ lbs} 1 short ton = 2 , 000 lbs . Rigging equipment, cranes, structural steel, and gravel deliveries in North America are rated in short tons.

Long Ton (Imperial UK): 1 long ton = 2 , 240 lbs 1\text{ long ton} = 2,240\text{ lbs} 1 long ton = 2 , 240 lbs (used historically in maritime freight).

Metric Ton (Tonne): 1 metric ton (t) = 1 , 000 kilograms (kg) = 2 , 204.62 lbs 1\text{ metric ton (t)} = 1,000\text{ kilograms (kg)} = 2,204.62\text{ lbs} 1 metric ton (t) = 1 , 000 kilograms (kg) = 2 , 204.62 lbs .

Pound-to-Kilogram Conversion: 1 kg ≈ 2.2046 lbs 1\text{ kg} \approx 2.2046\text{ lbs} 1 kg ≈ 2.2046 lbs ; 1 lb ≈ 0.4536 kg 1\text{ lb} \approx 0.4536\text{ kg} 1 lb ≈ 0.4536 kg .

Rigging Warning: Short Ton vs. Metric Ton Never confuse a short ton (2,000 lbs) with a metric ton (2,204.6 lbs) . A 50-metric-ton offshore modular unit weighs 50 × 2 , 204.6 = 110 , 230 lbs 50 \times 2,204.6 = 110,230\text{ lbs} 50 × 2 , 204.6 = 110 , 230 lbs , or 55.1 short tons . If a crane operator rigs the lift assuming a 50-short-ton load ( 100 , 000 lbs 100,000\text{ lbs} 100 , 000 lbs ), the crane will be overloaded by more than 10 , 200 lbs 10,200\text{ lbs} 10 , 200 lbs , risking catastrophic crane tip-over or structural boom collapse!

  • Liquid Volume Equivalencies
  • 8 fluid ounces (fl oz) = 1 cup 8\text{ fluid ounces (fl oz)} = 1\text{ cup} 8 fluid ounces (fl oz) = 1 cup

2 cups = 1 pint (pt) = 16 fl oz 2\text{ cups} = 1\text{ pint (pt)} = 16\text{ fl oz} 2 cups = 1 pint (pt) = 16 fl oz

2 pints = 1 quart (qt) = 32 fl oz 2\text{ pints} = 1\text{ quart (qt)} = 32\text{ fl oz} 2 pints = 1 quart (qt) = 32 fl oz

4 quarts = 1 gallon (gal) = 128 fl oz 4\text{ quarts} = 1\text{ gallon (gal)} = 128\text{ fl oz} 4 quarts = 1 gallon (gal) = 128 fl oz

Water Weight Standard: 1 gallon of pure water = 8.34 lbs 1\text{ gallon of pure water} = 8.34\text{ lbs} 1 gallon of pure water = 8.34 lbs ( 1 cubic foot of water = 7.48 gallons = 62.4 lbs 1\text{ cubic foot of water} = 7.48\text{ gallons} = 62.4\text{ lbs} 1 cubic foot of water = 7.48 gallons = 62.4 lbs ).

Metric Liquid Volume: 1 liter (L) = 1 , 000 milliliters (mL) 1\text{ liter (L)} = 1,000\text{ milliliters (mL)} 1 liter (L) = 1 , 000 milliliters (mL) ; 1 gallon (US) = 3.7854 liters 1\text{ gallon (US)} = 3.7854\text{ liters} 1 gallon (US) = 3.7854 liters ; 1 cubic meter (m 3 ) = 1 , 000 liters 1\text{ cubic meter (m}^3\text{)} = 1,000\text{ liters} 1 cubic meter (m 3 ) = 1 , 000 liters .