Study guide

4.2 Commercial Load Calculations

NCCER Commercial Electrician COMELEC26_01

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Electrical Safety, OSHA & NFPA 70E

1.1 OSHA Regulations & Subpart S Compliance 1.2 NFPA 70E Standards & Arc-Flash Protection 1.3 Lockout/Tagout (LOTO) & Absence-of-Voltage Verification 1.4 Jobsite Hazard Recognition & Fall/Trench Safety

2 Chapter 2: Electrical Theory & AC/DC Fundamentals

2.1 DC Fundamentals, Ohm's Law & Power 2.2 Series, Parallel & Combination Circuits 2.3 AC Fundamentals, Reactance & Magnetism 2.4 Impedance, Power Triangles & Power Factor

3 Chapter 3: NEC Layout, General Requirements & Services

3.1 NEC Structure, Navigation & Article 100 Definitions 3.2 NEC Article 110: General Requirements for Electrical Installations 3.3 NEC Article 230: Services & Service Equipment

4 Chapter 4: Branch Circuits, Feeders & Overcurrent Protection

4.1 Branch Circuits & Feeders 4.2 Commercial Load Calculations 4.3 Overcurrent Protection & Coordination

5 Chapter 5: Conductors, Insulation & Sizing Calculations

5.1 Conductor Construction, Materials & Insulation 5.2 Ampacity Determination & Table 310.16 5.3 Ampacity Derating & Adjustment Calculations 5.4 Conductor Installation, Pulling Tension & Splices

6 Chapter 6: Raceways, Boxes & Conduit Bending

6.1 Raceway Systems & Support Rules 6.2 Conduit Bending Principles & Mathematics 6.3 Raceway Fill Calculations 6.4 Box Sizing & Cable Tray Systems

7 Chapter 7: Commercial Wiring Methods, Devices & Special Occupancies

7.1 Commercial Wiring Devices & Receptacles 7.2 Switching Circuits & Commercial Controls 7.3 Commercial Lighting & Emergency Power Systems 7.4 Hazardous (Classified) Locations

8 Chapter 8: Motors, Motor Circuits & Overload Protection

8.1 Motor Principles & Nameplate Interpretation 8.2 Motor Feeder & Branch-Circuit Conductor Sizing 8.3 Motor Overload & Branch-Circuit Short-Circuit Protection

9 Chapter 9: Motor Controls, Ladder Logic & Industrial Drives

9.1 Magnetic Contactors, Starters & Relays 9.2 Control Circuits & Ladder Logic Schematics 9.3 Variable Frequency Drives (VFDs) & PLC Applications

10 Chapter 10: Transformers & Separately Derived Systems

10.1 Transformer Theory, Ratios & Single-Phase Connections 10.2 Three-Phase Transformer Configurations & Calculations 10.3 Transformer Sizing, Protection & Grounding

11 Chapter 11: Grounding & Bonding Systems (NEC Article 250)

11.1 Fundamental Concepts: Grounding vs. Bonding 11.2 Grounding Electrode System & GEC Sizing 11.3 Equipment Grounding Conductors (EGC) 11.4 Main, System & Supply-Side Bonding Jumpers

12 Chapter 12: Electrical Testing, Troubleshooting & Print Reading

12.1 Electrical Test Instruments & CAT Ratings 12.2 Systematic Circuit Troubleshooting & Fault Analysis 12.3 Electrical Drawings, Specifications & One-Line Diagrams 12.4 Fire Alarm Systems & Specialized Low-Voltage Wiring

4.2 Commercial Load Calculations

Key Takeaways Explain This Topic AI

Commercial general lighting loads are determined from NEC Table 220.12 unit loads (e.g., 1.3 VA/sq ft for office spaces) and must include a 125% multiplier for continuous operation per NEC 215.2.

General-purpose convenience receptacles are calculated at 180 VA per strap/yoke per NEC 220.14(I), with demand factors applied under Table 220.44 (100% of the first 10 kVA and 50% of the remainder).

Commercial kitchen equipment demand factors under Table 220.56 scale downward from 100% for 1-2 units, 90% for 3, 80% for 4, 70% for 5, to 65% for 6 or more units, provided the demand is not less than the two largest units.

When calculating non-coincident loads such as heating and air conditioning under NEC 220.60, the smaller load is omitted entirely and the larger load is used.

Feeder neutrals are calculated from the maximum unbalanced load under NEC 220.61. The permitted demand adjustment for the portion above 200A has exceptions, and the nonlinear-load portion identified by 220.61(C)(2) is not reduced.

Last updated: October 2026

4.2 Commercial Load Calculations

Designing commercial electrical services and feeders requires calculating prospective electrical loads under NEC Article 220 . Electricians and electrical designers must distinguish between connected load (the arithmetical sum of all nameplate ratings) and calculated demand load (the maximum power drawn simultaneously under real-world operating conditions). Applying statutory demand factors avoids massive over-sizing of copper, switchgear, and utility transformers while guaranteeing safety under peak operating conditions.

Structural Organization of NEC Article 220

NEC Article 220 is organized into five specialized parts:

Part I: General : Calculation definitions, nominal voltages, and rounding conventions.

Part II: Branch Circuit Load Calculations : Unit loads per square foot, receptacle ratings, and appliance calculations.

Part III: Feeder and Service Load Calculations : Standard calculation method, demand factor tables, and neutral sizing.

Part IV: Optional Feeder and Service Load Calculations : Simplified methods primarily applied to residential occupancies, restaurants, and schools.

Part V: Farm Load Calculations : Agricultural operations and farm buildings.

Commercial General Lighting Loads (NEC 220.12, 220.42, 215.2)

Commercial general lighting calculations use the unit load method. The floor area is calculated from the outside dimensions of the building or individual tenant lease space, multiplied by the specific unit load from NEC Table 220.12 :

General Lighting Connected Load (VA) = Gross Floor Area (sq ft) × Unit Load (VA/sq ft) \text{General Lighting Connected Load (VA)} = \text{Gross Floor Area (sq ft)} \times \text{Unit Load (VA/sq ft)} General Lighting Connected Load (VA) = Gross Floor Area (sq ft) × Unit Load (VA/sq ft)

Commercial Occupancy Type Table 220.12 Unit Load (VA/sq ft) Continuous Load Factor Typical Design Applications

Office Buildings 1.30 VA/sq ft 1.30\text{ VA/sq ft} 1.30 VA/sq ft 125 % 125\% 125% Administrative, commercial office space, tenant suites

Retail Stores 1.50 VA/sq ft 1.50\text{ VA/sq ft} 1.50 VA/sq ft 125 % 125\% 125% Department stores, boutiques, supermarkets, sales floors

Warehouses (Storage) 0.25 VA/sq ft 0.25\text{ VA/sq ft} 0.25 VA/sq ft 125 % 125\% 125% Commercial dry storage, logistics bays, distribution centers

Restaurants 1.60 VA/sq ft 1.60\text{ VA/sq ft} 1.60 VA/sq ft 125 % 125\% 125% Dining rooms, fast food seating, commercial food bars

Hotels & Motels 1.70 VA/sq ft 1.70\text{ VA/sq ft} 1.70 VA/sq ft 125 % 125\% 125% Guest rooms, ballrooms, lobbies (excluding dining)

Banks 1.40 VA/sq ft 1.40\text{ VA/sq ft} 1.40 VA/sq ft 125 % 125\% 125% Financial institutions, customer lobbies, teller lines

Note

Historical versions of the NEC listed 3.5 VA/sq ft 3.5\text{ VA/sq ft} 3.5 VA/sq ft for offices and 3.0 VA/sq ft 3.0\text{ VA/sq ft} 3.0 VA/sq ft for retail. In modern code cycles, Table 220.12 unit loads have been updated downward to reflect energy-efficient LED luminaires and modern energy conservation codes (such as ASHRAE 90.1 and IECC).

The Continuous Lighting Multiplier

In commercial occupancies, general lighting operates for 3 hours or more during normal business operations. Therefore, general lighting is classified as a continuous load under NEC Article 100. Under NEC 215.2(A)(1) and 230.42(A) , feeder and service conductors must be sized to carry 125% of the continuous lighting load:

Feeder Lighting Demand Load = Table 220.12 Calculated VA × 1.25 \text{Feeder Lighting Demand Load} = \text{Table 220.12 Calculated VA} \times 1.25 Feeder Lighting Demand Load = Table 220.12 Calculated VA × 1.25

Show Window & Sign Lighting

Show Windows (NEC 220.14(G)) : Must be calculated at either 200 VA per linear foot of show window or 1 , 200 VA 1,200\text{ VA} 1 , 200 VA per outlet, whichever produces the larger load.

Commercial Signs (NEC 220.14(F) & 600.5) : Every commercial occupancy accessible to pedestrians must have at least one dedicated 1,200 VA sign branch circuit included in the service calculation at 125% continuous duty ( 1 , 200 × 1.25 = 1 , 500 VA 1,200 \times 1.25 = 1,500\text{ VA} 1 , 200 × 1.25 = 1 , 500 VA ).

Receptacle Loads & Commercial Demand Factors (NEC 220.14(I) & Table 220.44)

In commercial occupancies, standard 15A and 20A convenience receptacle outlets are calculated at 180 VA per strap (yoke) under NEC 220.14(I) :

A standard duplex receptacle mounted on a single yoke counts as 180 VA .

A single receptacle on a single yoke counts as 180 VA .

A quad receptacle (two duplex receptacles on two separate yokes in a 2-gang box) counts as 360 VA .

Multi-Outlet Assemblies (NEC 220.14(H))

For plug-in strips or raceways with multiple fixed receptacle outlets:

Normal Commercial Use : Calculated at 180 VA for each 5-foot section or fraction thereof.

Heavy Simultaneous Use (workbenches, test benches, trade schools): Calculated at 180 VA for each 1-foot section or fraction thereof.

Receptacle Demand Factors (Table 220.44)

Unlike dwelling units, commercial convenience receptacle loads are not lumped with general lighting. Instead, the total connected receptacle VA is subject to the demand factors of NEC Table 220.44 :

  • Receptacle Load Range Demand Factor (NEC Table 220.44)
  • First 10 , 000 VA 10,000\text{ VA} 10 , 000 VA ( 10 kVA 10\text{ kVA} 10 kVA ) or less 100 % 100\% 100%
  • Portion of load exceeding 10 , 000 VA 10,000\text{ VA} 10 , 000 VA 50 % 50\% 50%
  • Commercial Kitchen Equipment Demand Factors (NEC Table 220.56)

Commercial kitchens feature high-density electrical cooking loads (convection ovens, commercial dishwashers, deep fryers, booster water heaters, steam tables). Because these thermostatically controlled appliances cycle on and off, NEC Table 220.56 permits a demand factor applied to the total nameplate rating of three or more units of commercial kitchen equipment:

  • Number of Commercial Kitchen Appliances Table 220.56 Demand Factor
  • 1 to 2 units 100 % 100\% 100%
  • 3 units 90 % 90\% 90%
  • 4 units 80 % 80\% 80%
  • 5 units 70 % 70\% 70%
  • 6 or more units 65 % 65\% 65%

[!CRITICAL] The Two-Largest Minimum Rule : In no case shall the calculated feeder kitchen demand load be less than the arithmetical sum of the ratings of the two largest kitchen appliances . If the percentage calculation produces a value smaller than the sum of the two largest units, the sum of the two largest units must be used.

  • Non-Coincident Loads (NEC 220.60) & Motor Loads (NEC 430.24)
  • Non-Coincident Loads (NEC 220.60)

Where it is unlikely that two or more dissimilar loads will be in use simultaneously, the electrician is permitted to use only the largest load that will be operated at any one time . The most common application is space heating versus air conditioning:

Compare the total cooling load (compressor, condenser fans, blower motors) against the total electric space heating load.

Include the larger load at 100% (or continuous rating) and completely omit the smaller load from the service calculation.

Motor Multipliers (NEC 220.50 & 430.24)

When sizing feeder or service conductors supplying multiple motors or a combination of motor and other loads, NEC 430.24 requires adding 25% of the Full-Load Current (FLC) of the single largest motor to the total connected motor load to accommodate motor inrush and starting transients.

Feeder Neutral Sizing & Harmonic Restrictions (NEC 220.61)

Under NEC 220.61 , the feeder neutral conductor must be sized to carry the maximum unbalanced load between the neutral and any one ungrounded conductor.

Permissible Neutral Derating

For linear loads (resistive heating, incandescent lamps), a demand factor of 70% is permitted for that portion of the unbalanced neutral load in excess of 200 amperes .

Non-Linear Load Restrictions (NEC 220.61(C)(2))

There shall be no reduction in neutral conductor ampacity for that portion of the load consisting of non-linear loads supplied from a 4-wire, 3-phase, wye-connected system.

Harmonic Distortion : Non-linear equipment (solid-state LED drivers, electronic ballasts, computer switch-mode power supplies, variable frequency drives) draws current in sharp pulses rather than smooth sine waves.

Triplen Harmonics : Third-harmonic currents (180 Hz) and odd multiples of three (9th, 15th, 21st) do not cancel out in the neutral conductor of a three-phase system; instead, they add arithmetically in the neutral .

As a result, neutral current can equal or exceed phase conductor current, requiring full-size or oversized neutral conductors.

  • Comprehensive Worked Commercial Service Calculation Example
  • Building Parameters

A new 15,000 sq ft commercial office building is supplied by a 120/208V, 3-phase, 4-wire electrical service. Calculate the minimum service rating in amperes based on the following loads:

  • Building Area : 15 , 000 sq ft 15,000\text{ sq ft} 15 , 000 sq ft of general office space
  • Show Window : 25 linear feet
  • Convenience Receptacles : 140 general-purpose duplex receptacles

Breakroom Commercial Kitchen Equipment (4 thermostatically controlled units):

  • Commercial booster dishwasher: 9.0 kW 9.0\text{ kW} 9.0 kW
  • Electric warming oven: 6.0 kW 6.0\text{ kW} 6.0 kW
  • Commercial deep fryer: 8.0 kW 8.0\text{ kW} 8.0 kW
  • Commercial microwave/convection: 5.0 kW 5.0\text{ kW} 5.0 kW

HVAC Loads (Non-Coincident):

  • 3-Phase Air Conditioning (Cooling): 42.0 kVA 42.0\text{ kVA} 42.0 kVA
  • Electric Space Heating: 30.0 kW 30.0\text{ kW} 30.0 kW

Largest Motor : The largest individual motor is a 15 HP rooftop chiller compressor drawing 46.2 A 46.2\text{ A} 46.2 A at 208V 3-phase ( 16 , 644 VA 16,644\text{ VA} 16 , 644 VA ).

  • Step-by-Step Calculation
  • Step 1: General Lighting Load (NEC 220.12 & 215.2)

Table 220.12 Unit Load = 15 , 000 sq ft × 1.30 VA/sq ft = 19 , 500 VA \text{Table 220.12 Unit Load} = 15,000\text{ sq ft} \times 1.30\text{ VA/sq ft} = 19,500\text{ VA} Table 220.12 Unit Load = 15 , 000 sq ft × 1.30 VA/sq ft = 19 , 500 VA Continuous Multiplier (125%) = 19 , 500 VA × 1.25 = 24 , 375 VA \text{Continuous Multiplier (125\%)} = 19,500\text{ VA} \times 1.25 = 24,375\text{ VA} Continuous Multiplier (125%) = 19 , 500 VA × 1.25 = 24 , 375 VA

Step 2: Show Window Load (NEC 220.14(G))

Show Window Load = 25 ft × 200 VA/ft = 5 , 000 VA \text{Show Window Load} = 25\text{ ft} \times 200\text{ VA/ft} = 5,000\text{ VA} Show Window Load = 25 ft × 200 VA/ft = 5 , 000 VA Continuous Multiplier (125%) = 5 , 000 VA × 1.25 = 6 , 250 VA \text{Continuous Multiplier (125\%)} = 5,000\text{ VA} \times 1.25 = 6,250\text{ VA} Continuous Multiplier (125%) = 5 , 000 VA × 1.25 = 6 , 250 VA

Step 3: General Receptacle Load (NEC 220.14(I) & Table 220.44)

Connected Receptacle Load = 140 duplexes × 180 VA = 25 , 200 VA \text{Connected Receptacle Load} = 140\text{ duplexes} \times 180\text{ VA} = 25,200\text{ VA} Connected Receptacle Load = 140 duplexes × 180 VA = 25 , 200 VA Applying Table 220.44 Demand Factors:

First 10 , 000 VA 10,000\text{ VA} 10 , 000 VA at 100 % = 10 , 000 VA 100\% = 10,000\text{ VA} 100% = 10 , 000 VA

Remainder over 10 , 000 VA 10,000\text{ VA} 10 , 000 VA : ( 25 , 200 − 10 , 000 ) × 0.50 = 15 , 200 × 0.50 = 7 , 600 VA (25,200 - 10,000) \times 0.50 = 15,200 \times 0.50 = 7,600\text{ VA} ( 25 , 200 − 10 , 000 ) × 0.50 = 15 , 200 × 0.50 = 7 , 600 VA Net Calculated Receptacle Demand = 10 , 000 VA + 7 , 600 VA = 17 , 600 VA \text{Net Calculated Receptacle Demand} = 10,000\text{ VA} + 7,600\text{ VA} = 17,600\text{ VA} Net Calculated Receptacle Demand = 10 , 000 VA + 7 , 600 VA = 17 , 600 VA

Step 4: Commercial Kitchen Equipment (NEC Table 220.56)

Total connected kitchen load (4 units): Total Nameplate = 9.0 + 6.0 + 8.0 + 5.0 = 28.0 kW = 28 , 000 VA \text{Total Nameplate} = 9.0 + 6.0 + 8.0 + 5.0 = 28.0\text{ kW} = 28,000\text{ VA} Total Nameplate = 9.0 + 6.0 + 8.0 + 5.0 = 28.0 kW = 28 , 000 VA From Table 220.56, demand factor for 4 units is 80% : Demand Load = 28 , 000 VA × 0.80 = 22 , 400 VA \text{Demand Load} = 28,000\text{ VA} \times 0.80 = 22,400\text{ VA} Demand Load = 28 , 000 VA × 0.80 = 22 , 400 VA Check two largest units rule: Largest are Dishwasher ( 9.0 kW 9.0\text{ kW} 9.0 kW ) and Fryer ( 8.0 kW 8.0\text{ kW} 8.0 kW ): 9 , 000 VA + 8 , 000 VA = 17 , 000 VA 9,000\text{ VA} + 8,000\text{ VA} = 17,000\text{ VA} 9 , 000 VA + 8 , 000 VA = 17 , 000 VA Since 22 , 400 VA ≥ 17 , 000 VA 22,400\text{ VA} \ge 17,000\text{ VA} 22 , 400 VA ≥ 17 , 000 VA , the 22,400 VA demand load is accepted.

  • Step 5: Non-Coincident HVAC Loads (NEC 220.60)
  • Cooling = 42 , 000 VA 42,000\text{ VA} 42 , 000 VA

Heating = 30 , 000 VA 30,000\text{ VA} 30 , 000 VA Comparing the two, cooling ( 42 , 000 VA 42,000\text{ VA} 42 , 000 VA ) is larger than heating ( 30 , 000 VA 30,000\text{ VA} 30 , 000 VA ). Omit the heating load entirely and include 42,000 VA for cooling.

Step 6: Motor Multiplier (NEC 430.24)

Add 25% of the largest motor load: Motor 25% Adder = 16 , 644 VA × 0.25 = 4 , 161 VA \text{Motor 25\% Adder} = 16,644\text{ VA} \times 0.25 = 4,161\text{ VA} Motor 25% Adder = 16 , 644 VA × 0.25 = 4 , 161 VA

Step 7: Total Calculated Service Demand (VA)

  • Load Component Calculated Demand (VA)
  • General Lighting (125%) 24 , 375 VA 24,375\text{ VA} 24 , 375 VA
  • Show Window (125%) 6 , 250 VA 6,250\text{ VA} 6 , 250 VA
  • Receptacles (Table 220.44) 17 , 600 VA 17,600\text{ VA} 17 , 600 VA
  • Kitchen Equipment (80%) 22 , 400 VA 22,400\text{ VA} 22 , 400 VA
  • Cooling Load (Largest) 42 , 000 VA 42,000\text{ VA} 42 , 000 VA
  • Motor 25% Adder 4 , 161 VA 4,161\text{ VA} 4 , 161 VA
  • Total Calculated Load 116 , 786 VA 116,786\text{ VA} 116 , 786 VA
  • Step 8: Sizing the Main Service Overcurrent Protective Device

Calculate the total three-phase line current at 208V:

I = Total VA V L − L × 3 = 116 , 786 VA 208 V × 1.732 = 116 , 786 360.26 ≈ 324.2 Amperes I = \frac{\text{Total VA}}{V_{L-L} \times \sqrt{3}} = \frac{116,786\text{ VA}}{208\text{ V} \times 1.732} = \frac{116,786}{360.26} \approx 324.2\text{ Amperes} I = V L − L ​ × 3 ​ Total VA ​ = 208 V × 1.732 116 , 786 VA ​ = 360.26 116 , 786 ​ ≈ 324.2 Amperes

Consulting NEC 240.6(A) for standard breaker ratings, the next standard size above 324.2A is 350 Amperes or a 400 Ampere service switchboard.

Loading diagram... Commercial Service Load Calculation Process Flow