Study guide
8.2 Motor Feeder & Branch-Circuit Conductor Sizing
NCCER Commercial Electrician COMELEC26_01
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Electrical Safety, OSHA & NFPA 70E
1.1 OSHA Regulations & Subpart S Compliance 1.2 NFPA 70E Standards & Arc-Flash Protection 1.3 Lockout/Tagout (LOTO) & Absence-of-Voltage Verification 1.4 Jobsite Hazard Recognition & Fall/Trench Safety
2 Chapter 2: Electrical Theory & AC/DC Fundamentals
2.1 DC Fundamentals, Ohm's Law & Power 2.2 Series, Parallel & Combination Circuits 2.3 AC Fundamentals, Reactance & Magnetism 2.4 Impedance, Power Triangles & Power Factor
3 Chapter 3: NEC Layout, General Requirements & Services
3.1 NEC Structure, Navigation & Article 100 Definitions 3.2 NEC Article 110: General Requirements for Electrical Installations 3.3 NEC Article 230: Services & Service Equipment
4 Chapter 4: Branch Circuits, Feeders & Overcurrent Protection
4.1 Branch Circuits & Feeders 4.2 Commercial Load Calculations 4.3 Overcurrent Protection & Coordination
5 Chapter 5: Conductors, Insulation & Sizing Calculations
5.1 Conductor Construction, Materials & Insulation 5.2 Ampacity Determination & Table 310.16 5.3 Ampacity Derating & Adjustment Calculations 5.4 Conductor Installation, Pulling Tension & Splices
6 Chapter 6: Raceways, Boxes & Conduit Bending
6.1 Raceway Systems & Support Rules 6.2 Conduit Bending Principles & Mathematics 6.3 Raceway Fill Calculations 6.4 Box Sizing & Cable Tray Systems
7 Chapter 7: Commercial Wiring Methods, Devices & Special Occupancies
7.1 Commercial Wiring Devices & Receptacles 7.2 Switching Circuits & Commercial Controls 7.3 Commercial Lighting & Emergency Power Systems 7.4 Hazardous (Classified) Locations
8 Chapter 8: Motors, Motor Circuits & Overload Protection
8.1 Motor Principles & Nameplate Interpretation 8.2 Motor Feeder & Branch-Circuit Conductor Sizing 8.3 Motor Overload & Branch-Circuit Short-Circuit Protection
9 Chapter 9: Motor Controls, Ladder Logic & Industrial Drives
9.1 Magnetic Contactors, Starters & Relays 9.2 Control Circuits & Ladder Logic Schematics 9.3 Variable Frequency Drives (VFDs) & PLC Applications
10 Chapter 10: Transformers & Separately Derived Systems
10.1 Transformer Theory, Ratios & Single-Phase Connections 10.2 Three-Phase Transformer Configurations & Calculations 10.3 Transformer Sizing, Protection & Grounding
11 Chapter 11: Grounding & Bonding Systems (NEC Article 250)
11.1 Fundamental Concepts: Grounding vs. Bonding 11.2 Grounding Electrode System & GEC Sizing 11.3 Equipment Grounding Conductors (EGC) 11.4 Main, System & Supply-Side Bonding Jumpers
12 Chapter 12: Electrical Testing, Troubleshooting & Print Reading
12.1 Electrical Test Instruments & CAT Ratings 12.2 Systematic Circuit Troubleshooting & Fault Analysis 12.3 Electrical Drawings, Specifications & One-Line Diagrams 12.4 Fire Alarm Systems & Specialized Low-Voltage Wiring
8.2 Motor Feeder & Branch-Circuit Conductor Sizing
Key Takeaways Explain This Topic AI
Under NEC 430.22, conductors supplying a single continuous-duty motor must have an allowable ampacity of not less than 125% of the motor full-load current (FLC) from NEC Table 430.248 or 430.250.
Under NEC 430.24, feeder conductors supplying multiple motors must have an ampacity of at least 125% of the largest motor FLC plus the sum of the full-load currents of all other motors in the group.
When a feeder supplies motors combined with other loads, the feeder ampacity equals 125% of the largest motor FLC + sum of other motor FLCs + 125% of continuous non-motor loads + 100% of noncontinuous loads per NEC 220.50.
NEC Part IX (430.102) requires a motor disconnecting means to be located within sight from the motor and driven machinery (visible and not more than 50 feet distant), rated in horsepower and at least 115% of motor Table FLC.
Conductor termination temperature rules per NEC 110.14(C) require evaluating conductors at 75°C ampacities for commercial equipment rated over 100A or marked for 75°C, while allowing 90°C ratings for ambient derating and raceway bundling adjustments.
Last updated: October 2026
8.2 Motor Feeder & Branch-Circuit Conductor Sizing
Motor circuits present unique electrical demands that differentiate them from general lighting and appliance branch circuits. Motors draw massive starting inrush currents—typically five to eight times normal operating current—and subject conductors to continuous thermal stress under mechanical loading. Consequently, NEC Article 430 mandates specialized rules for conductor sizing, terminal temperature evaluations, and disconnecting means.
Branch-Circuit Conductor Sizing for a Single Motor (NEC 430.22)
Under NEC 430.22 , conductors supplying a single motor used in a continuous-duty application must have an allowable ampacity of not less than 125 % 125\% 125% of the motor full-load current (FLC) determined from the applicable NEC table (Table 430.248 for single-phase, or Table 430.250 for three-phase):
I conductor ≥ 1.25 × I FLC (Table) I_{\text{conductor}} \ge 1.25 \times I_{\text{FLC (Table)}} I conductor ≥ 1.25 × I FLC (Table)
Why 125% Ampacity?
Continuous-duty motors are classified as continuous loads under Article 100 (loads where the maximum current is expected to continue for 3 hours or more). Sizing conductors to 125 % 125\% 125% prevents thermal accumulation inside raceways and enclosures, dissipates internal I 2 R I^2R I 2 R resistive heating, and guarantees that terminal connections at the motor controller and disconnect switch remain below their listed operating temperature limits.
Noncontinuous and Duty-Cycle Motors (NEC Table 430.22(E))
If a motor is not rated for continuous duty, the conductor sizing multiplier is determined from NEC Table 430.22(E) based on duty classification:
Short-Time Duty (operating for 5, 15, 30, or 60 minutes): Multipliers range from 110 % 110\% 110% to 200 % 200\% 200% .
Intermittent Duty (alternate intervals of load and no-load): Multipliers range from 130 % 130\% 130% to 150 % 150\% 150% .
Periodic Duty (regular repetition of load cycles): Multipliers range from 130 % 130\% 130% to 200 % 200\% 200% .
Varying Duty (loads vary widely over time): Conductor ampacity must be at least 140 % 140\% 140% to 200 % 200\% 200% .
In standard commercial electrical construction, the vast majority of motors (fans, pumps, chillers, air compressors) are continuous-duty, requiring the universal 125 % 125\% 125% multiplier .
Terminal Temperature Ratings & Ampacity Derating (NEC 110.14(C))
When selecting conductors from NEC Table 310.16 , electricians must navigate the termination temperature provisions of NEC 110.14(C) :
Equipment Rated 100 Amperes or Less (or 14 AWG through 1 AWG) : Conductors must be selected based on the 60 ∘ C 60^\circ\text{C} 6 0 ∘ C column of Table 310.16, unless the equipment terminals are listed and marked for 75 ∘ C 75^\circ\text{C} 7 5 ∘ C . In modern commercial construction, virtually all motor controllers, disconnect switches, and circuit breakers carry dual 75 ∘ C 75^\circ\text{C} 7 5 ∘ C or 60 ∘ / 75 ∘ C 60^\circ/75^\circ\text{C} 6 0 ∘ /7 5 ∘ C listings , permitting selection from the 75 ∘ C 75^\circ\text{C} 7 5 ∘ C column.
Equipment Rated Over 100 Amperes : Conductors are permitted to be selected based on the 75 ∘ C 75^\circ\text{C} 7 5 ∘ C column of Table 310.16.
Using 90°C Insulated Conductors (THHN / XHHW-2) : Even when conductors have a 90 ∘ C 90^\circ\text{C} 9 0 ∘ C insulation rating (such as THHN or THWN-2), the final ampacity landed on equipment terminals cannot exceed the terminal rating (typically 75 ∘ C 75^\circ\text{C} 7 5 ∘ C ). However, the 90 ∘ C 90^\circ\text{C} 9 0 ∘ C rating is permitted as the starting point for applying ambient temperature correction factors (Table 310.15(B)(1)) and conductor bundling adjustment factors (Table 310.15(C)(1) for more than three current-carrying conductors in a raceway).
Note
Small Conductor Rule Exemption : NEC 240.4(D) restricts 14 AWG copper to 15A overcurrent protection, 12 AWG copper to 20A, and 10 AWG copper to 30A. However, NEC 240.4(G) specifically exempts motor circuits, directing electricians to Article 430. Because motor branch-circuit short-circuit protection is sized much higher to allow starting, 14, 12, and 10 AWG conductors in motor circuits are permitted to carry their full 75 ∘ C 75^\circ\text{C} 7 5 ∘ C table ampacities ( 20 A 20\text{A} 20 A for 14 AWG, 25 A 25\text{A} 25 A for 12 AWG, and 35 A 35\text{A} 35 A for 10 AWG).
Sizing Feeder Conductors for Multiple Motors (NEC 430.24)
When a single feeder raceway or busway supplies two or more motors, diversity dictates that not all motors will pull locked-rotor starting current simultaneously. However, the largest motor may start while all other motors are already operating at full continuous load.
Therefore, under NEC 430.24 , conductors supplying several motors must have an allowable ampacity not less than 125 % 125\% 125% of the highest rated motor full-load current (FLC) plus the sum of the full-load currents of all other motors in the group:
I feeder ≥ ( 1.25 × I largest FLC ) + ∑ I other FLCs I_{\text{feeder}} \ge (1.25 \times I_{\text{largest FLC}}) + \sum I_{\text{other FLCs}} I feeder ≥ ( 1.25 × I largest FLC ) + ∑ I other FLCs
Critical Application Rules for NEC 430.24:
Determining the Largest Motor : The "largest motor" is strictly the motor with the highest full-load current (FLC) from NEC Tables 430.248 or 430.250, not necessarily the motor with the highest nameplate horsepower rating.
Identical Highest Ratings : If two or more motors have identical highest full-load currents, only one is multiplied by 125 % 125\% 125% ; all other motors are added at 100 % 100\% 100% .
Combining Motor Loads with Other Loads on a Feeder (NEC 220.50)
In commercial distribution systems, a distribution panel feeder frequently supplies a mix of motor loads, continuous general lighting, and noncontinuous convenience receptacle circuits. Under NEC 220.50 and NEC 430.24 , the feeder conductor ampacity is determined using the combined formula:
I total feeder ≥ ( 1.25 × I largest motor FLC ) + ∑ I other motor FLCs + ( 1.25 × I continuous non-motor ) + ∑ I noncontinuous non-motor I_{\text{total feeder}} \ge (1.25 \times I_{\text{largest motor FLC}}) + \sum I_{\text{other motor FLCs}} + (1.25 \times I_{\text{continuous non-motor}}) + \sum I_{\text{noncontinuous non-motor}} I total feeder ≥ ( 1.25 × I largest motor FLC ) + ∑ I other motor FLCs + ( 1.25 × I continuous non-motor ) + ∑ I noncontinuous non-motor
This calculation ensures that every continuous load is backed by 125 % 125\% 125% conductor thermal capacity while preventing compounding of safety factors on noncontinuous loads.
Motor Disconnecting Means: Location & Ratings (NEC Part IX)
NEC Article 430 Part IX establishes rigid safety rules ensuring electricians and maintenance personnel can physically de-energize and lock out a motor to prevent accidental startup during mechanical servicing:
1. Location Requirements (NEC 430.102)
In Sight From Controller : A disconnecting means must be located in sight from the motor controller location (NEC 430.102(A)).
In Sight From Motor Location : A disconnecting means must also be located in sight from the motor location and the driven machinery (NEC 430.102(B)).
Definition of "In Sight From" (Article 100) : The specified equipment must be visible and not more than 50 feet (15 meters) distant from the other equipment.
Warning
The 50-Foot Rule : Even if a disconnect switch is in direct, unobstructed line-of-sight from a rooftop chiller, if the physical distance between the switch and the chiller exceeds 50 feet, it violates NEC 430.102(B) . A second disconnect must be installed within 50 feet of the chiller.
Lockable Disconnect Exception (NEC 430.102(B)(2) Ex.) : The disconnect adjacent to the motor is permitted to be omitted if the disconnect located at the controller can be locked in the open position in accordance with NEC 110.25 (the locking provision must remain in place with or without the padlock installed), and either:
Locating the disconnect near the motor is impracticable or introduces greater hazards (e.g., inside hazardous chemical vapor zones), or
The installation is in an industrial facility with written safety procedures and qualified maintenance personnel.
2. Disconnect Type (NEC 430.109)
The disconnecting means must be one of the following listed types:
A listed horsepower-rated motor-circuit switch .
A listed molded case circuit breaker .
A listed molded case switch (non-automatic circuit interrupter).
A listed manual motor controller marked "Suitable as Motor Disconnect" installed on the load side of branch-circuit protection.
For motors of 1 8 HP \frac{1}{8}\text{ HP} 8 1 HP or less: General-use snap switch.
3. Disconnect Ampere & Horsepower Ratings (NEC 430.110)
Under NEC 430.110(A) , the disconnecting means for a single motor circuit must satisfy two distinct engineering ratings:
Ampere Rating : The switch or breaker must have an continuous ampere rating of at least 115 % 115\% 115% of the motor full-load current (FLC) from Table 430.248 or 430.250: Disconnect Minimum Amperes ≥ 1.15 × I FLC (Table) \text{Disconnect Minimum Amperes} \ge 1.15 \times I_{\text{FLC (Table)}} Disconnect Minimum Amperes ≥ 1.15 × I FLC (Table)
Horsepower Rating : The switch must carry a nominal horsepower rating equal to or greater than the motor nameplate horsepower rating.
Step-by-Step Worked Calculation: Commercial HVAC Installation
To see how these principles coalesce into real-world practice, let us engineer the branch circuits, disconnect switches, and common feeder for a commercial mechanical equipment room served by a 460-volt, 3-phase, 60 Hz distribution panelboard.
Installation Specifications:
Motor 1 (Water-Cooled Chiller) : 50 HP, 460V, 3-phase, continuous-duty squirrel-cage induction motor.
Motor 2 (Chilled Water Pump) : 15 HP, 460V, 3-phase, continuous-duty squirrel-cage induction motor.
Motor 3 (Condenser Water Pump) : 10 HP, 460V, 3-phase, continuous-duty squirrel-cage induction motor.
Motor 4 (Mechanical Room Exhaust Fan) : 3 HP, 460V, 3-phase, continuous-duty squirrel-cage induction motor.
Wiring Method : Single raceway (EMT) supplying copper THHN/THWN-2 conductors landed on equipment terminals rated for 75 ∘ C 75^\circ\text{C} 7 5 ∘ C . 460V / 3-Phase Main Distribution Feeder
- │
- ├─── [Feeder OCPD] ──── (Feeder Conductors: Sized per 430.24)
- │
- ▼ Distribution Panelboard
- ├─── [Branch 1] ──> Disconnect ──> Controller ──> 50 HP Chiller (FLC = 65A)
- ├─── [Branch 2] ──> Disconnect ──> Controller ──> 15 HP Chilled Pump (FLC = 21A)
- ├─── [Branch 3] ──> Disconnect ──> Controller ──> 10 HP Condenser Pump (FLC = 14A)
- └─── [Branch 4] ──> Disconnect ──> Controller ──> 3 HP Exhaust Fan (FLC = 4.8A)
- Step 1: Look Up Table FLCs (NEC Table 430.250)
Per NEC 430.6(A)(1), we look up the full-load currents from NEC Table 430.250 for three-phase AC motors at 460 volts:
- Motor 1 (50 HP) : FLC = 65 Amperes \text{FLC} = 65\text{ Amperes} FLC = 65 Amperes
- Motor 2 (15 HP) : FLC = 21 Amperes \text{FLC} = 21\text{ Amperes} FLC = 21 Amperes
- Motor 3 (10 HP) : FLC = 14 Amperes \text{FLC} = 14\text{ Amperes} FLC = 14 Amperes
- Motor 4 (3 HP) : FLC = 4.8 Amperes \text{FLC} = 4.8\text{ Amperes} FLC = 4.8 Amperes
- Step 2: Sizing Individual Branch-Circuit Conductors (NEC 430.22)
Apply the 125 % 125\% 125% multiplier to each Table FLC and select conductors from the 75 ∘ C 75^\circ\text{C} 7 5 ∘ C column of NEC Table 310.16 (Copper THHN/THWN-2):
Motor 1 (50 HP, FLC = 65 A) : I conductor ≥ 1.25 × 65 A = 81.25 Amperes I_{\text{conductor}} \ge 1.25 \times 65\text{ A} = 81.25\text{ Amperes} I conductor ≥ 1.25 × 65 A = 81.25 Amperes
Table 310.16 ( 75 ∘ C 75^\circ\text{C} 7 5 ∘ C Cu): 4 AWG is rated 85 Amperes ( 85 A ≥ 81.25 A 85\text{ A} \ge 81.25\text{ A} 85 A ≥ 81.25 A ).
Select: 4 AWG Copper THHN/THWN-2 .
Motor 2 (15 HP, FLC = 21 A) : I conductor ≥ 1.25 × 21 A = 26.25 Amperes I_{\text{conductor}} \ge 1.25 \times 21\text{ A} = 26.25\text{ Amperes} I conductor ≥ 1.25 × 21 A = 26.25 Amperes
Table 310.16 ( 75 ∘ C 75^\circ\text{C} 7 5 ∘ C Cu): 10 AWG is rated 35 Amperes ( 35 A ≥ 26.25 A 35\text{ A} \ge 26.25\text{ A} 35 A ≥ 26.25 A ).
(Note: 240.4(G) permits 10 AWG to carry its full 35A 75°C ampacity in motor branch circuits) .
Select: 10 AWG Copper THHN/THWN-2 .
Motor 3 (10 HP, FLC = 14 A) : I conductor ≥ 1.25 × 14 A = 17.5 Amperes I_{\text{conductor}} \ge 1.25 \times 14\text{ A} = 17.5\text{ Amperes} I conductor ≥ 1.25 × 14 A = 17.5 Amperes
Table 310.16 ( 75 ∘ C 75^\circ\text{C} 7 5 ∘ C Cu): 14 AWG is rated 20 Amperes ( 20 A ≥ 17.5 A 20\text{ A} \ge 17.5\text{ A} 20 A ≥ 17.5 A ).
(Engineering best practice on commercial projects often specifies a minimum of 12 AWG for mechanical strength, rated 25A at 75°C; however, code minimum is 14 AWG) .
Select: 14 AWG (or 12 AWG) Copper THHN/THWN-2 .
Motor 4 (3 HP, FLC = 4.8 A) : I conductor ≥ 1.25 × 4.8 A = 6.0 Amperes I_{\text{conductor}} \ge 1.25 \times 4.8\text{ A} = 6.0\text{ Amperes} I conductor ≥ 1.25 × 4.8 A = 6.0 Amperes
Table 310.16 ( 75 ∘ C 75^\circ\text{C} 7 5 ∘ C Cu): 14 AWG is rated 20 Amperes ( 20 A ≥ 6.0 A 20\text{ A} \ge 6.0\text{ A} 20 A ≥ 6.0 A ).
Select: 14 AWG Copper THHN/THWN-2 .
Step 3: Sizing Disconnecting Means (NEC 430.110)
Each motor must have a disconnect switch within sight (visible and within 50 feet) satisfying minimum ampere ( 115 % FLC 115\%\text{ FLC} 115% FLC ) and horsepower ratings:
Motor 1 (50 HP) : Minimum Amperes = 1.15 × 65 A = 74.75 A = 1.15 \times 65\text{ A} = 74.75\text{ A} = 1.15 × 65 A = 74.75 A . Standard switch size is 100 Ampere, 50 HP-rated switch .
Motor 2 (15 HP) : Minimum Amperes = 1.15 × 21 A = 24.15 A = 1.15 \times 21\text{ A} = 24.15\text{ A} = 1.15 × 21 A = 24.15 A . Standard switch size is 30 Ampere, 15 HP-rated switch .
Motor 3 (10 HP) : Minimum Amperes = 1.15 × 14 A = 16.1 A = 1.15 \times 14\text{ A} = 16.1\text{ A} = 1.15 × 14 A = 16.1 A . Standard switch size is 30 Ampere, 10 HP-rated switch .
Motor 4 (3 HP) : Minimum Amperes = 1.15 × 4.8 A = 5.52 A = 1.15 \times 4.8\text{ A} = 5.52\text{ A} = 1.15 × 4.8 A = 5.52 A . Standard switch size is 30 Ampere, 3 HP-rated switch (or listed manual motor controller).
Step 4: Sizing Feeder Conductors Supplying All Four Motors (NEC 430.24)
Under NEC 430.24, the feeder ampacity must equal 125 % 125\% 125% of the highest rated motor FLC plus the sum of all other motor FLCs:
Highest rated motor: Motor 1 (50 HP, FLC = 65 A \text{FLC} = 65\text{ A} FLC = 65 A )
Other motor FLCs: 21 A + 14 A + 4.8 A = 39.8 A 21\text{ A} + 14\text{ A} + 4.8\text{ A} = 39.8\text{ A} 21 A + 14 A + 4.8 A = 39.8 A
I feeder ≥ ( 1.25 × 65 A ) + 21 A + 14 A + 4.8 A I_{\text{feeder}} \ge (1.25 \times 65\text{ A}) + 21\text{ A} + 14\text{ A} + 4.8\text{ A} I feeder ≥ ( 1.25 × 65 A ) + 21 A + 14 A + 4.8 A I feeder ≥ 81.25 A + 39.8 A = 121.05 Amperes I_{\text{feeder}} \ge 81.25\text{ A} + 39.8\text{ A} = 121.05\text{ Amperes} I feeder ≥ 81.25 A + 39.8 A = 121.05 Amperes
Now, select the feeder conductor from NEC Table 310.16 ( 75 ∘ C 75^\circ\text{C} 7 5 ∘ C Column, Copper):
2 AWG Copper is rated 115 Amperes ( 115 A < 121.05 A 115\text{ A} < 121.05\text{ A} 115 A < 121.05 A — too small ).
1 AWG Copper is rated 130 Amperes ( 130 A ≥ 121.05 A 130\text{ A} \ge 121.05\text{ A} 130 A ≥ 121.05 A — compliant ).
Select: 1 AWG Copper THHN/THWN-2 conductors for the feeder .
Step 5: Feeder Sizing with Mixed Continuous & Noncontinuous Loads
Suppose the feeder also supplies:
- Continuous mechanical room fluorescent/LED lighting: 16 Amperes 16\text{ Amperes} 16 Amperes
- Noncontinuous convenience utility receptacles: 10 Amperes 10\text{ Amperes} 10 Amperes
Applying NEC 220.50: I feeder total = 121.05 A (Motors) + ( 1.25 × 16 A continuous ) + 10 A noncontinuous I_{\text{feeder total}} = 121.05\text{ A (Motors)} + (1.25 \times 16\text{ A continuous}) + 10\text{ A noncontinuous} I feeder total = 121.05 A (Motors) + ( 1.25 × 16 A continuous ) + 10 A noncontinuous I feeder total = 121.05 A + 20 A + 10 A = 151.05 Amperes I_{\text{feeder total}} = 121.05\text{ A} + 20\text{ A} + 10\text{ A} = 151.05\text{ Amperes} I feeder total = 121.05 A + 20 A + 10 A = 151.05 Amperes
Evaluating Table 310.16 ( 75 ∘ C 75^\circ\text{C} 7 5 ∘ C Cu):
1/0 AWG Copper is rated 150 Amperes ( 150 A < 151.05 A 150\text{ A} < 151.05\text{ A} 150 A < 151.05 A — slightly undersized).
2/0 AWG Copper is rated 175 Amperes ( 175 A ≥ 151.05 A 175\text{ A} \ge 151.05\text{ A} 175 A ≥ 151.05 A — compliant ).
Select: 2/0 AWG Copper THHN/THWN-2 conductors .