Study guide
10.1 Transformer Theory, Ratios & Single-Phase Connections
NCCER Commercial Electrician COMELEC26_01
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Electrical Safety, OSHA & NFPA 70E
1.1 OSHA Regulations & Subpart S Compliance 1.2 NFPA 70E Standards & Arc-Flash Protection 1.3 Lockout/Tagout (LOTO) & Absence-of-Voltage Verification 1.4 Jobsite Hazard Recognition & Fall/Trench Safety
2 Chapter 2: Electrical Theory & AC/DC Fundamentals
2.1 DC Fundamentals, Ohm's Law & Power 2.2 Series, Parallel & Combination Circuits 2.3 AC Fundamentals, Reactance & Magnetism 2.4 Impedance, Power Triangles & Power Factor
3 Chapter 3: NEC Layout, General Requirements & Services
3.1 NEC Structure, Navigation & Article 100 Definitions 3.2 NEC Article 110: General Requirements for Electrical Installations 3.3 NEC Article 230: Services & Service Equipment
4 Chapter 4: Branch Circuits, Feeders & Overcurrent Protection
4.1 Branch Circuits & Feeders 4.2 Commercial Load Calculations 4.3 Overcurrent Protection & Coordination
5 Chapter 5: Conductors, Insulation & Sizing Calculations
5.1 Conductor Construction, Materials & Insulation 5.2 Ampacity Determination & Table 310.16 5.3 Ampacity Derating & Adjustment Calculations 5.4 Conductor Installation, Pulling Tension & Splices
6 Chapter 6: Raceways, Boxes & Conduit Bending
6.1 Raceway Systems & Support Rules 6.2 Conduit Bending Principles & Mathematics 6.3 Raceway Fill Calculations 6.4 Box Sizing & Cable Tray Systems
7 Chapter 7: Commercial Wiring Methods, Devices & Special Occupancies
7.1 Commercial Wiring Devices & Receptacles 7.2 Switching Circuits & Commercial Controls 7.3 Commercial Lighting & Emergency Power Systems 7.4 Hazardous (Classified) Locations
8 Chapter 8: Motors, Motor Circuits & Overload Protection
8.1 Motor Principles & Nameplate Interpretation 8.2 Motor Feeder & Branch-Circuit Conductor Sizing 8.3 Motor Overload & Branch-Circuit Short-Circuit Protection
9 Chapter 9: Motor Controls, Ladder Logic & Industrial Drives
9.1 Magnetic Contactors, Starters & Relays 9.2 Control Circuits & Ladder Logic Schematics 9.3 Variable Frequency Drives (VFDs) & PLC Applications
10 Chapter 10: Transformers & Separately Derived Systems
10.1 Transformer Theory, Ratios & Single-Phase Connections 10.2 Three-Phase Transformer Configurations & Calculations 10.3 Transformer Sizing, Protection & Grounding
11 Chapter 11: Grounding & Bonding Systems (NEC Article 250)
11.1 Fundamental Concepts: Grounding vs. Bonding 11.2 Grounding Electrode System & GEC Sizing 11.3 Equipment Grounding Conductors (EGC) 11.4 Main, System & Supply-Side Bonding Jumpers
12 Chapter 12: Electrical Testing, Troubleshooting & Print Reading
12.1 Electrical Test Instruments & CAT Ratings 12.2 Systematic Circuit Troubleshooting & Fault Analysis 12.3 Electrical Drawings, Specifications & One-Line Diagrams 12.4 Fire Alarm Systems & Specialized Low-Voltage Wiring
10.1 Transformer Theory, Ratios & Single-Phase Connections
Key Takeaways Explain This Topic AI
Transformers operate on Faraday's Law of electromagnetic induction and mutual induction, transferring electrical energy between electrically isolated circuits via an alternating magnetic flux in a laminated silicon steel core.
The fundamental transformer equations establish that the turns ratio directly dictates the voltage ratio and inversely dictates the current ratio: N p N s = V p V s = I s I p \frac{N_p}{N_s} = \frac{V_p}{V_s} = \frac{I_s}{I_p} N s N p = V s V p = I p I s , preserving apparent power ( S p ≈ S s S_p \approx S_s S p ≈ S s ).
Transformer losses comprise load-dependent copper losses ( I 2 R I^2R I 2 R resistive heating in windings) and constant no-load core iron losses (hysteresis from magnetic domain realignment and eddy currents suppressed by thin, insulated laminations).
Transformer nameplate percent impedance (%Z) defines the primary voltage drop required to circulate rated secondary short-circuit current, governing available fault current ( I s c = I F L A % Z / 100 I_{sc} = \frac{I_{FLA}}{\%Z / 100} I sc = % Z /100 I F L A ) for equipment rating coordination.
Dual-voltage windings connect in series for high voltage and parallel for low voltage (H1–H4, X1–X4), with ANSI/IEEE polarity classified as additive ( ≤ 200 kVA , ≤ 8660 V \le 200\text{ kVA}, \le 8660\text{V} ≤ 200 kVA , ≤ 8660 V ) or subtractive (all larger and polyphase units).
Last updated: October 2026
10.1 Transformer Theory, Ratios & Single-Phase Connections
Transformers are static electromagnetic machines that transfer electrical power from one alternating-current (AC) circuit to another without changing frequency. In commercial and industrial electrical distribution, transformers step generation and transmission voltages (e.g., 13.8 kV, 4,160V) down to utilization levels (e.g., 480V, 208V, 240V, 120V) while electrically isolating systems to enhance safety and limit fault energy. Commercial electricians must master electromagnetic coupling principles, core loss mechanisms, turns and impedance ratios, ANSI polarity conventions, and dual-voltage terminal connections.
Principles of Operation: Mutual Induction & Core Physics
Transformers operate on the principle of mutual induction governed by Faraday's Law of Electromagnetic Induction and Lenz's Law :
Faraday's Law : When magnetic flux linked with an electrical circuit changes over time, an electromotive force (EMF) is induced across the winding terminals proportional to the rate of change of magnetic flux and the number of turns ( e = − N d Φ d t e = -N \frac{d\Phi}{dt} e = − N d t d Φ ).
Primary Winding : Connected to the alternating AC power source. Alternating current flowing through the primary coil magnetizes the core, producing an alternating magnetic flux ( Φ \Phi Φ ) that continuously expands, collapses, and reverses direction at line frequency (60 Hz in North America).
Secondary Winding : Mechanically placed on the same magnetic core but electrically isolated from the primary. The alternating magnetic flux circulating through the closed magnetic core cuts the turns of the secondary winding, inducing an alternating secondary voltage.
Mutual Induction : The process by which an alternating current in one winding induces a voltage in an adjacent winding through a shared magnetic field, without direct metallic contact.
Core Construction: Silicon Steel & Geometry
Transformer cores provide a high-permeability, low-reluctance magnetic path to channel magnetic flux efficiently between primary and secondary windings.
Magnetic Material : Cores are manufactured from high-grade, cold-rolled, grain-oriented silicon steel (typically containing 3% to 4% silicon). Silicon increases electrical resistivity, reducing core eddy currents, while cold rolling aligns the crystalline lattice structure along the direction of magnetic flux to maximize magnetic permeability.
Core Geometry :
Core-Type Construction : The copper windings surround two vertical laminated steel legs. Each leg carries half of the primary and half of the secondary windings (concentric coils, with low-voltage coils placed closest to the core and high-voltage coils wrapped outside). This design provides excellent physical separation and cooling for high-voltage commercial transformers.
Shell-Type Construction : The steel core surrounds and encloses the windings. Cores have three vertical legs: a wide central leg carrying the full magnetic flux surrounded by the primary and secondary coils (often interleaved as pancake coils), flanked by two outer return legs that carry half of the total flux each. Shell-type transformers offer superior mechanical bracing against severe short-circuit electromagnetic forces.
The Ideal Transformer & Mathematical Ratios
An ideal transformer assumes 100% magnetic coupling ( k = 1.0 k = 1.0 k = 1.0 ), zero core hysteresis or eddy current losses, zero winding resistance, and zero leakage flux. Under these theoretical conditions, the electrical power delivered to the primary equals the electrical power transferred to the secondary:
S p = S s ⟹ V p × I p = V s × I s S_p = S_s \implies V_p \times I_p = V_s \times I_s S p = S s ⟹ V p × I p = V s × I s
Fundamental Ratio Equations
The relationship between primary and secondary turns ( N N N ), voltages ( V V V ), and currents ( I I I ) is defined by the transformation ratio ( a a a ) :
N p N s = V p V s = I s I p = a \frac{N_p}{N_s} = \frac{V_p}{V_s} = \frac{I_s}{I_p} = a N s N p = V s V p = I p I s = a
Where:
- N p N_p N p = Number of turns in the primary winding
- N s N_s N s = Number of turns in the secondary winding
- V p V_p V p = Primary terminal voltage in Volts
- V s V_s V s = Secondary terminal voltage in Volts
- I p I_p I p = Primary line current in Amperes
- I s I_s I s = Secondary line current in Amperes
- a a a = Turns ratio (transformation ratio)
- Voltage vs. Current Inversion
Step-Down Transformer ( a > 1 a > 1 a > 1 ) : Primary turns exceed secondary turns ( N p > N s N_p > N_s N p > N s ). Secondary voltage is lower than primary voltage ( V s < V p V_s < V_p V s < V p ), but secondary current capacity is proportionately higher ( I s > I p I_s > I_p I s > I p ).
Step-Up Transformer ( a < 1 a < 1 a < 1 ) : Secondary turns exceed primary turns ( N s > N p N_s > N_p N s > N p ). Secondary voltage increases ( V s > V p V_s > V_p V s > V p ), while secondary current decreases ( I s < I p I_s < I_p I s < I p ).
Note
A transformer does not generate power; it transforms electrical energy. If secondary voltage is reduced by a factor of 4 (e.g., 480V to 120V), secondary current capacity increases by a factor of 4, keeping total volt-amperes ( V × I V \times I V × I ) constant.
Transformer Losses & Operating Efficiency
In practical real-world transformers, conversion efficiency ranges from 95% to 99% . Energy losses manifest as heat inside the transformer enclosure and fall into two distinct engineering categories: copper losses and core (iron) losses . Total Transformer Losses
- |
- +-----------------------+-----------------------+
- | |
- Copper Losses ($I^2R$) Core Losses (Iron)
- (Varies with Load Current) (Constant No-Load Loss)
- | |
- v +---------------+---------------+
- Winding Heat Generation | |
- ($P_{cu} \propto I_{load}^2$) Hysteresis Losses Eddy Current Losses
- (Domain Realignment) (Circulating Core Currents)
- Reduced by Silicon Steel Reduced by Thin Laminations
- 1. Copper Losses ( I 2 R I^2R I 2 R Load Losses)
Copper losses represent electrical power dissipated as heat due to the natural electrical resistance of the primary and secondary winding conductors ( R p R_p R p and R s R_s R s ):
P c u = I p 2 R p + I s 2 R s P_{cu} = I_p^2 R_p + I_s^2 R_s P c u = I p 2 R p + I s 2 R s
Because copper losses are directly proportional to the square of the operating current ( I 2 I^2 I 2 ), they are called load losses . When a transformer operates at 50% load, its copper losses drop to ( 1 2 ) 2 = 1 4 (\frac{1}{2})^2 = \frac{1}{4} ( 2 1 ) 2 = 4 1 (25%) of full-load copper loss. At 100% rated load, copper losses reach their maximum.
2. Core / Iron Losses (No-Load Losses)
Core losses occur within the ferromagnetic steel core whenever the transformer is energized, regardless of whether a load is connected to the secondary terminals. Core losses comprise two distinct physical phenomena:
Hysteresis Loss : As alternating current cycles at 60 Hz, the microscopic magnetic domains (dipoles) in the silicon steel core must physically flip orientation 120 times every second. The molecular friction of continually reversing these magnetic domains consumes energy, dissipating it as heat. Hysteresis loss is minimized by using high-permeability, cold-rolled grain-oriented silicon steel with a narrow hysteresis loop ( B − H B-H B − H curve).
Eddy Current Loss : The alternating magnetic flux passing through the conductive steel core induces internal swirling voltages within the iron itself, in accordance with Faraday's Law. Because the steel core has low electrical resistance, these induced voltages drive circulating electrical currents—termed eddy currents —through the core mass, generating severe parasitic heating ( P e ∝ f 2 B m a x 2 t 2 P_e \propto f^2 B_{max}^2 t^2 P e ∝ f 2 B ma x 2 t 2 , where t t t is lamination thickness).
The Lamination Solution : To suppress eddy currents, transformer cores are never cast as solid blocks of metal. Instead, they are constructed from stacks of very thin sheets ( laminations ), typically 0.010 to 0.014 inches thick. Each sheet is electrically insulated from adjacent sheets by an inorganic varnish, oxide coating, or chemical phosphate film. Thin laminations confine eddy currents to tiny loops within individual sheets, increasing total resistance and cutting eddy current losses by over 98%.
Transformer Impedance (%Z) & Available Short-Circuit Current
The percent impedance (%Z) stamped on a transformer nameplate is one of the most critical values for commercial electricians. It governs voltage regulation, voltage drop under load, and the maximum short-circuit current the transformer can deliver during a bolted line-to-line or line-to-ground fault.
What Does %Z Represent Physically?
To measure %Z in a testing laboratory:
The secondary terminals are bolted dead short ( 0 Ω 0\,\Omega 0 Ω load).
A variable voltage is applied to the primary terminals and gradually increased until rated full-load current flows through the short-circuited secondary.
The voltage required to circulate rated current, expressed as a percentage of the rated primary voltage, is the percent impedance (%Z) .
% Z = V p r i m a r y (to produce rated short-circuit current) V p r i m a r y (rated nominal) × 100 % \%Z = \frac{V_{primary\text{ (to produce rated short-circuit current)}}}{V_{primary\text{ (rated nominal)}}} \times 100\% % Z = V p r ima ry (rated nominal) V p r ima ry (to produce rated short-circuit current) × 100%
For typical dry-type commercial distribution transformers (15 kVA to 500 kVA), %Z ranges between 2.0% and 6.0% (typically 3.0% to 5.0%).
Available Short-Circuit Current ( I s c I_{sc} I sc ) Calculation
Percent impedance establishes the maximum fault current that can discharge from the secondary terminals into a dead short. Assuming an infinite utility source bus on the primary side, available secondary short-circuit current is calculated as:
I s c = I F L A % Z 100 = I F L A × 100 % Z I_{sc} = \frac{I_{FLA}}{\frac{\%Z}{100}} = I_{FLA} \times \frac{100}{\%Z} I sc = 100 % Z I F L A = I F L A × % Z 100
Where:
- I s c I_{sc} I sc = Maximum symmetrical available short-circuit current at secondary terminals in Amperes
- I F L A I_{FLA} I F L A = Rated full-load secondary current in Amperes
- % Z \%Z % Z = Nameplate percent impedance
- Step-by-Step Calculation: Available Fault Current
Problem : A 50 kVA, single-phase, 480V primary to 120/240V secondary commercial dry-type transformer has a nameplate impedance of 3.5% Z . Calculate the secondary full-load current and the maximum available short-circuit current at the 240V secondary terminals.
Calculate Secondary Full-Load Amperes ( I F L A I_{FLA} I F L A ) : I F L A = kVA × 1000 V s e c o n d a r y = 50 × 1000 240 V = 50 , 000 240 = 208.33 A I_{FLA} = \frac{\text{kVA} \times 1000}{V_{secondary}} = \frac{50 \times 1000}{240\text{V}} = \frac{50,000}{240} = 208.33\text{ A} I F L A = V seco n d a ry kVA × 1000 = 240 V 50 × 1000 = 240 50 , 000 = 208.33 A
Calculate Secondary Short-Circuit Current ( I s c I_{sc} I sc ) : I s c = I F L A % Z 100 = 208.33 3.5 100 = 208.33 0.035 = 5 , 952.38 A ≈ 5 , 952 A I_{sc} = \frac{I_{FLA}}{\frac{\%Z}{100}} = \frac{208.33}{\frac{3.5}{100}} = \frac{208.33}{0.035} = 5,952.38\text{ A} \approx 5,952\text{ A} I sc = 100 % Z I F L A = 100 3.5 208.33 = 0.035 208.33 = 5 , 952.38 A ≈ 5 , 952 A
Warning
Electrical equipment downstream of this transformer—including panelboards, disconnect switches, and circuit breakers—must have an Interrupting Rating (AIC / AIR) or Short-Circuit Current Rating (SCCR) equal to or exceeding 5,952 Amperes to prevent catastrophic explosive failure during an electrical fault (NEC 110.9 and 110.10).
ANSI Transformer Polarity: Additive vs. Subtractive
Polarity designates the relative direction of induced secondary voltage with respect to applied primary voltage at a specific instantaneous moment in time. ANSI/IEEE C57.12.00 governs transformer terminal labeling and polarity:
High-Voltage Terminals : Labeled H1 and H2 .
Low-Voltage Terminals : Labeled X1 and X2 .
Terminal Convention : When facing the high-voltage side of the transformer enclosure, terminal H1 is always on the left , and H2 is on the right . SUBTRACTIVE POLARITY ADDITIVE POLARITY
(Standard for > 200 kVA or > 8660V) (Standard for <= 200 kVA and <= 8660V)
- H1 H2 H1 H2
- +----------------------+ +----------------------+
- | PRIMARY | | PRIMARY |
- | | | |
- | SECONDARY | | SECONDARY |
- +----------------------+ +----------------------+
- X1 X2 X2 X1
- (X1 directly adjacent to H1) (X1 diagonally opposite to H1)
- Polarity Definitions
Subtractive Polarity : Terminal X1 is directly adjacent to H1 (on the left when facing the low-voltage side). If you jumper H1 to X1 and apply a test AC voltage across H1 and H2, a voltmeter placed between H2 and X2 reads the difference between primary and secondary voltages ( V t e s t = V H − V X V_{test} = V_H - V_X V t es t = V H − V X ).
Additive Polarity : Terminal X1 is diagonally opposite H1 (terminal X2 is on the left, X1 is on the right). If you jumper H1 to X2 and apply test voltage across H1 and H2, a voltmeter between H2 and X1 reads the sum of primary and secondary voltages ( V t e s t = V H + V X V_{test} = V_H + V_X V t es t = V H + V X ).
The ANSI Industry Polarity Standard
Under ANSI/IEEE C57.12.00 , standard polarity is established as follows:
Additive Polarity : Mandated for single-phase transformers rated ≤ 200 kVA \le 200\text{ kVA} ≤ 200 kVA having a high-voltage winding rating of ≤ 8 , 660 Volts \le 8,660\text{ Volts} ≤ 8 , 660 Volts .
Subtractive Polarity : Mandated for all single-phase transformers rated > 200 kVA > 200\text{ kVA} > 200 kVA (regardless of voltage), all single-phase transformers with primary voltages > 8 , 660 Volts > 8,660\text{ Volts} > 8 , 660 Volts (regardless of kVA), and all three-phase transformers .
Transformer Classification kVA Rating High-Voltage Rating Standard ANSI Polarity
Small / Medium Distribution ≤ 200 kVA \le 200\text{ kVA} ≤ 200 kVA ≤ 8 , 660 V \le 8,660\text{V} ≤ 8 , 660 V ADDITIVE
- Large Single-Phase > 200 kVA > 200\text{ kVA} > 200 kVA Any Voltage SUBTRACTIVE
- High-Voltage Single-Phase Any kVA > 8 , 660 V > 8,660\text{V} > 8 , 660 V SUBTRACTIVE
- All Three-Phase Units Any kVA Any Voltage SUBTRACTIVE
- Single-Phase Dual-Voltage Transformers: Series vs. Parallel
Commercial single-phase transformers frequently feature dual-voltage primary windings (e.g., 240V / 480V) and dual-voltage secondary windings (e.g., 120V / 240V). This enables field electricians to adapt a single stock transformer to multiple utility voltage configurations:
Primary coils: H1–H2 (Coil 1, rated 240V) and H3–H4 (Coil 2, rated 240V).
Secondary coils: X1–X2 (Coil 1, rated 120V) and X3–X4 (Coil 2, rated 120V).
1. High-Voltage Connection: Series Wiring
To operate on the higher voltage rating, the two individual windings are connected in series so their voltage ratings add together:
480V Primary Series Configuration : Connect terminal H2 to H3 with a factory jumper. Connect the 480V supply lines to H1 and H4 . V H = V H 1 − H 2 + V H 3 − H 4 = 240 V + 240 V = 480 V V_H = V_{H1-H2} + V_{H3-H4} = 240\text{V} + 240\text{V} = 480\text{V} V H = V H 1 − H 2 + V H 3 − H 4 = 240 V + 240 V = 480 V
240V / 120V Secondary Series Configuration (3-Wire Edison) : Connect terminal X2 to X3 . Connect ungrounded feeder conductors to X1 and X4 (providing 240V line-to-line), and connect the grounded neutral conductor to the X2–X3 jumper (providing 120V from X1 to neutral, and 120V from X4 to neutral). Primary Series Connection (480V Supply)
- Line 1 (480V) ---> H1 ====== H2 + (Jumper H2 to H3)
- |
- Line 2 (480V) ---> H4 ====== H3 +
- Secondary Series Connection (120/240V 3-Wire Supply)
- Line 1 (120V) ---> X1 ====== X2 + (Jumper X2 to X3)
- | ---> Neutral (120V to X1 / 120V to X4)
- Line 2 (120V) ---> X4 ====== X3 +
- (240V Line-to-Line across X1 and X4)
- 2. Low-Voltage Connection: Parallel Wiring
To operate on the lower voltage rating, the two individual windings are connected in parallel so their current carrying capacities add together:
240V Primary Parallel Configuration : Jumper H1 to H3 , and jumper H2 to H4 . Connect Line 1 to the H1–H3 pair and Line 2 to the H2–H4 pair. Each coil receives 240V, and primary current divides equally between the two windings.
120V Secondary Parallel Configuration (2-Wire) : Jumper X1 to X3 , and jumper X2 to X4 . Connect the ungrounded conductor to X1–X3 and the grounded conductor to X2–X4. The entire kVA capacity of the transformer is available at 120V single-phase. Primary Parallel Connection (240V Supply)
- Line 1 (240V) ---> H1 ====== H2 ---> Line 2 (240V)
- | |
- +-- H3 +-- H4
- Secondary Parallel Connection (120V 2-Wire Supply)
- Line 1 (120V) ---> X1 ====== X2 ---> Neutral
- | |
- +-- X3 +-- X4
Tip
Memory Aid for Field Wiring :
High Voltage = Series : Link the inside terminals together ( H2 to H3 , X2 to X3 ). Connect lines to the outside terminals ( H1 and H4 , X1 and X4 ).
Low Voltage = Parallel : Link odd terminals together ( H1 to H3 , X1 to X3 ) and even terminals together ( H2 to H4 , X2 to X4 ).
- Step-by-Step Worked Transformer Calculations
- Example 1: Full-Load Current and Turns Ratio
Scenario : A 25 kVA single-phase dual-voltage distribution transformer is configured for 480V primary and 120/240V 3-wire secondary operation.
Calculate Primary Full-Load Current ( I p I_p I p ) : I p = kVA × 1000 V p = 25 × 1000 480 = 25 , 000 480 = 52.08 Amperes I_p = \frac{\text{kVA} \times 1000}{V_p} = \frac{25 \times 1000}{480} = \frac{25,000}{480} = 52.08\text{ Amperes} I p = V p kVA × 1000 = 480 25 × 1000 = 480 25 , 000 = 52.08 Amperes
Calculate Secondary Full-Load Current at 240V ( I s I_s I s ) : I s = kVA × 1000 V s = 25 × 1000 240 = 25 , 000 240 = 104.17 Amperes I_s = \frac{\text{kVA} \times 1000}{V_s} = \frac{25 \times 1000}{240} = \frac{25,000}{240} = 104.17\text{ Amperes} I s = V s kVA × 1000 = 240 25 × 1000 = 240 25 , 000 = 104.17 Amperes
Calculate the Overall Turns Ratio ( a a a ) : a = V p V s = 480 V 240 V = 2 : 1 a = \frac{V_p}{V_s} = \frac{480\text{V}}{240\text{V}} = 2:1 a = V s V p = 240 V 480 V = 2 : 1
Verify Current Transformation : I s = I p × a = 52.08 A × 2 = 104.16 Amperes I_s = I_p \times a = 52.08\text{ A} \times 2 = 104.16\text{ Amperes} I s = I p × a = 52.08 A × 2 = 104.16 Amperes