Study guide

15.1 Soil Mechanics: Bank, Loose & Compacted Cubic Yards

NCCER Heavy Equipment Operations Certification Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: NCCER Credentials, Trade Orientation, Safety & Equipment Classification

1.1 NCCER Heavy Equipment Operations Credentials, Curriculum & Assessments 1.2 Heavy Equipment Industry & Operator Responsibilities 1.3 OSHA & MSHA Regulatory Standards (29 CFR 1926 & 30 CFR) 1.4 Machine Safety Systems: ROPS, FOPS, Seatbelts & Interlocks 1.5 Classifying Heavy Equipment: Machine Families, Mining Machines, Drive Systems & Hydraulics

2 Chapter 2: Pre-Operation Inspection & Preventative Maintenance

2.1 Walk-Around Inspection Procedures & Daily Checklists 2.2 Fluid Levels, Hydraulic Inspection & Filter Maintenance 2.3 Undercarriage, Tires, Tracks & Ground Engaging Tools (GET) 2.4 Engine Systems, Startup & Warm-Up, and Hybrid and Electric Equipment Readiness

3 Chapter 3: Safe Operating Practices & Site Hazards

3.1 Mounting, Dismounting (Three-Point Contact) & Cab Safety 3.2 Electrical Power Line Clearances & Overhead Hazards 3.3 Blind Spots, Swing Radii, Spotters & Hand Signals

4 Chapter 4: Refueling, Parking, Shutdown & Equipment Transport

4.1 Engine Cooldown, Safe Parking & Lockout/Tagout Procedures 4.2 Fueling Safety, Fire Prevention & Environmental Controls 4.3 Heavy Equipment Transport, Rigging & Securement / Tie-Down

5 Chapter 5: Excavator Types, Components & Hydraulics

5.1 Excavator Classifications, Tracked vs. Wheeled Configurations 5.2 House, Boom, Stick, Bucket & Hydraulic Flow Systems 5.3 Quick-Couplers, Attachments & Operational Safety

6 Chapter 6: Excavator Operations, Trenching & Lifting

6.1 Excavator Positioning, Travel & Stable Working Platforms 6.2 Trenching Techniques, Bench Cutting & Production Digging 6.3 Lifting Operations, Rigging Capacities & Load Charts

7 Chapter 7: Backhoe Loader Components & Controls

7.1 Backhoe Loader Anatomy: Loader End vs. Backhoe End 7.2 Operator Station, Pilot vs. Wobble Stick Controls & Instruments 7.3 Stabilizer Deployment, Machine Levelling & Setup on Slopes

8 Chapter 8: Backhoe Loader Operational Techniques

8.1 Backhoe Digging, Spoiling, Truck Loading & Cycle Efficiency 8.2 Front-End Loader Operations with Backhoe Loaders 8.3 Backhoe Road Travel, Transport Safety & Boom Locking

9 Chapter 9: Bulldozer Types, Powertrains & Blade Configurations

9.1 Crawler Dozer Classifications, Undercarriages & Ground Pressure 9.2 Drivetrains: Torque Converters, Powershift & Hydrostatic Drives 9.3 Blade Types: Straight (S), Universal (U), Semi-Universal (SU) & Angle Blades

10 Chapter 10: Bulldozer Earthmoving Operations

10.1 Straight Dozing, Slot Dozing & Production Pushing 10.2 Push-Loading Scrapers & Multi-Machine Earthmoving 10.3 Stockpiling, Berm Construction & Material Spreading

11 Chapter 11: Dozer Slope Work, Ripping & Clearing

11.1 Sidehill Operations, Working Up and Down Steep Slopes 11.2 Ripper Attachments: Single Shank, Multi-Shank & Ripping Techniques 11.3 Site Clearing, Tree Felling & Stumping Precautions

12 Chapter 12: Wheel Loaders & Track Loaders

12.1 Wheel Loader Anatomy, Articulated Steering & Z-Bar Linkage 12.2 Loading Patterns: V-Pattern, I-Pattern & Truck Placement 12.3 Excavation, Stockpile Management & Carry Operations

13 Chapter 13: Motor Grader Anatomy & Blade Geometry

13.1 Motor Grader Components: Tandem Drive, Articulation & Front Wheel Lean 13.2 Moldboard Mechanics: Pitch, Angle, Lift & Side-Shift 13.3 Grader Safety, Operating Speeds & Reversing Precautions

14 Chapter 14: Motor Grader Operations & Finish Grading

14.1 Ditching, Backsloping & Windrowing Techniques 14.2 Roadway Crown, Cross-Slope & Superelevation Creation 14.3 Fine Grading Tolerances, Blue Tops & Final Trimming

15 Chapter 15: Earthmoving Principles, Excavation Math, Soils & Planning

15.1 Soil Mechanics: Bank, Loose & Compacted Cubic Yards 15.2 Swell, Shrinkage & Load Factor Calculations 15.3 Slope Ratios, Percent Grade & Elevation Calculations 15.4 Soil Classification Systems (USCS & AASHTO) and Soil Effects on Equipment 15.5 Earthmoving Planning & Soil Stabilization Methods

16 Chapter 16: Civil Drawings, Staking, Layout, Pipe Laying & Machine Control

16.1 Reading Civil Engineering Site Plans, Contours & Profiles 16.2 Construction Stakes: Stationing, Offset, Cut & Fill Stakes 16.3 Laser Levels, GNSS/GPS Machine Control & 3D Telematics 16.4 Foundation Layout & Pipe Laying

17 Chapter 17: Soil Compaction Equipment & Methods

17.1 Principles of Soil Compaction & Optimum Moisture Content (Proctor Test) 17.2 Roller Types: Smooth Drum, Padfoot / Sheepsfoot, Pneumatic & Tamping 17.3 Lift Thickness, Pass Overlap & In-Place Density Testing

18 Chapter 18: OSHA 1926 Subpart P: Soil Classification & Cave-In Protection

18.1 OSHA Soil Mechanics: Type A, Type B & Type C Classification 18.2 Cave-In Protection Systems: Sloping, Benching, Shoring & Shielding 18.3 Duties of the OSHA Competent Person & Daily Trench Inspections

19 Chapter 19: Excavation Site Hazards & Underground Utilities

19.1 Utility Locating (811 Call Before You Dig) & Potholing Procedures 19.2 Safe Access, Egress (Ladders/Ramps) & Hazardous Atmospheres 19.3 Surface Water Diversion, Dewatering & Backfilling Requirements

20 Chapter 20: Specialized Equipment: Compact Loaders, Forklifts, Haulers & Tractors

20.1 Skid-Steer Loaders & Compact Track Loaders (CTLs): Controls & Stability 20.2 Rough-Terrain Forklifts & Telehandlers: Stability Triangle & Load Charts 20.3 Scrapers, Off-Road Articulated Dump Trucks & Utility Tractors 20.4 Dump Trucks: On-Road and Off-Road Operation 20.5 Utility Tractors: ROPS, Overturn Prevention, Ballast & Implement Hookup 20.6 Conventional (Sit-Down Counterbalanced) Forklifts

15.1 Soil Mechanics: Bank, Loose & Compacted Cubic Yards

Key Takeaways Explain This Topic AI

Soil and rock exist in three distinct volumetric states during earthwork operations: undisturbed Bank Cubic Yards (BCY), excavated Loose Cubic Yards (LCY), and engineered Compacted Cubic Yards (CCY).

Excavating native ground fractures cohesive bonds and introduces air voids, causing material to swell into LCY, which dictates haul truck body capacities, scraper payloads, and equipment cycle requirements.

Mechanical compaction expels air from void spaces, forcing soil particles into dense structural contact to create CCY, resulting in a compacted volume that is typically smaller than the original bank volume.

Conservation of mass dictates that total dry solid mineral weight remains constant throughout excavation and compaction, while bulk density, void ratio, and volume fluctuate across the three physical states.

Last updated: October 2026

  • Soil Mechanics: Bank, Loose & Compacted Cubic Yards
  • Fundamental Soil States in Heavy Earthmoving

In heavy civil construction, highway engineering, and site development, earthmoving operations involve excavating, hauling, placing, and densifying millions of tons of geologic material. A fundamental principle of construction earthwork is that soil and rock undergo dramatic physical changes in volume and density as they are manipulated by heavy machinery. Earth does not maintain a constant volume throughout the construction cycle. Instead, material transitions through three distinct, mutually dependent volumetric states: Bank Cubic Yards (BCY), Loose Cubic Yards (LCY), and Compacted Cubic Yards (CCY).

Understanding these three states is essential for heavy equipment operators, grade foremen, and project estimators. Equipment selection, haul truck fleet dispatching, production scheduling, mass haul diagrams, and contract payment accounting depend directly on accurately identifying and calculating material volumes in their respective states:

Bank Cubic Yards (BCY) : Bank cubic yards represent earth and rock in its natural, in-situ, undisturbed state prior to excavation. In the bank state, soil particles have consolidated over geological epochs under the sustained overburden pressure of overlying strata, achieving natural mechanical interlock, stable grain orientation, and equilibrium moisture content. In civil engineering contracts, excavation quantities, cut-and-fill balances, and bid pay items are almost universally defined, measured, and compensated in Bank Cubic Yards based on original ground topographical surveys.

Loose Cubic Yards (LCY) : Loose cubic yards represent material after it has been disturbed, fractured, and excavated by equipment such as hydraulic excavators, crawler bulldozers, wheel loaders, or rippers. As cutting edges and bucket teeth pry the soil matrix apart, cohesive bonds between soil grains are severed, and ambient air is introduced into the expanding interstitial spaces. This volumetric expansion—known as soil swell—results in a material that occupies significantly more space than it did in the undisturbed bank cut. Haul truck bodies, scraper bowls, loader buckets, and conveyor hoppers are sized, rated, and loaded based on Loose Cubic Yards.

Compacted Cubic Yards (CCY) : Compacted cubic yards represent soil after it has been placed in controlled structural lifts, conditioned with moisture, and mechanically densified by compaction machinery such as smooth-drum vibratory rollers, padfoot (sheepsfoot) compactors, or heavy pneumatic rollers. Mechanical compaction exerts dynamic impact, kneading, and static pressure to force entrapped air voids out of the soil mass, bringing solid soil particles into dense structural contact. In cohesive and granular soils, this densification results in a final compacted volume that is smaller than the original in-situ bank volume. Structural building pads, highway subgrades, bridge abutment backfills, and earthen dam embankments are specified and verified in Compacted Cubic Yards.

Soil Physics: Void Ratio, Porosity, and Volumetric Phase Relationships

To understand why soil volume expands during digging and contracts under compaction rollers, operators must understand basic soil phase relationships. Soil is not a solid, monolithic block. Instead, it is a three-phase multiphase system composed of solid mineral grains, liquid water filling pore channels, and gases (air) occupying unsaturated voids.

Two primary geotechnical parameters define the structural spacing between soil particles:

Void Ratio ( e e e ) : The void ratio is defined as the mathematical ratio of the volume of void spaces ( V v V_v V v ​ , containing air and water) to the volume of solid mineral matter ( V s V_s V s ​ ): e = V v V s e = \frac{V_v}{V_s} e = V s ​ V v ​ ​

Porosity ( n n n ) : Porosity represents the percentage of total soil volume ( V t V_t V t ​ ) occupied by voids: n = ( V v V t ) × 100 % = ( e 1 + e ) × 100 % n = \left(\frac{V_v}{V_t}\right) \times 100\% = \left(\frac{e}{1 + e}\right) \times 100\% n = ( V t ​ V v ​ ​ ) × 100% = ( 1 + e e ​ ) × 100%

When heavy equipment excavates undisturbed bank material, the volume of solid mineral particles ( V s V_s V s ​ ) remains completely unchanged, but the volume of voids ( V v V_v V v ​ ) expands dramatically as ambient air enters the loosened mass. The void ratio increases from its low in-situ bank value ( e b a n k e_{bank} e bank ​ ) to a high loose value ( e l o o s e e_{loose} e l oose ​ ). Consequently, the total volume increases, while the overall bulk density drops. When that same material is spread across an embankment fill in thin 6-to-8-inch lifts and traversed by compaction rollers, dynamic compaction forces air out of the voids, driving the void ratio down to a compact minimum ( e c o m p a c t e d e_{compacted} e co m p a c t e d ​ ). For cohesive soils, e c o m p a c t e d e_{compacted} e co m p a c t e d ​ is typically lower than the original in-situ bank void ratio, meaning the engineered fill achieves a higher particle density than natural native ground.

Unit Weights and Density Measurements Across Soil Types

Density—commonly referred to in heavy construction as unit weight—is the measure of mass per unit volume. In the United States customary system, earthwork densities are expressed in pounds per cubic yard (lb/yd³ or lb/cu yd) or pounds per cubic foot (pcf, where 1 pcf × 27 = lb/cu yd 1\text{ pcf} \times 27 = \text{lb/cu yd} 1 pcf × 27 = lb/cu yd ).

Because earthwork volume changes across the three physical states while solid mineral mass remains constant, the unit weight of a given soil changes inversely with its volumetric state:

Bank Density ( γ b \gamma_b γ b ​ ) : The unit weight of undisturbed native earth in the cut. For example, a dense clay might exhibit a bank density of 3,000 lb/BCY.

Loose Density ( γ l \gamma_l γ l ​ ) : The unit weight of excavated material in a haul truck bed or stockpile. Because the material has swelled to occupy more volume, its mass per cubic yard decreases. The same clay with a 30% swell exhibits a loose density of 2,308 lb/LCY.

Compacted Density ( γ c \gamma_c γ c ​ ) : The dry unit weight of soil after engineered compaction on a fill embankment. Because air voids have been expelled, the mass per cubic yard reaches its highest value. That same clay compacted to engineered specifications might achieve a compacted density of 3,850 lb/CCY (about 22 percent shrinkage relative to the bank).

The fundamental law of mass conservation governs all earthmoving transformations: Total Solid Mass = V B C Y × γ b , dry = V L C Y × γ l , dry = V C C Y × γ c , dry \text{Total Solid Mass} = V_{BCY} \times \gamma_{b,\text{dry}} = V_{LCY} \times \gamma_{l,\text{dry}} = V_{CCY} \times \gamma_{c,\text{dry}} Total Solid Mass = V BC Y ​ × γ b , dry ​ = V L C Y ​ × γ l , dry ​ = V CC Y ​ × γ c , dry ​

Technical Comparison: Soil Volumetric States, Unit Weights & Void Ratios

The table below contrasts typical volumetric states, unit weights, void ratios, and structural behaviors across primary soil classifications:

Soil Classification Bank Density (lb/BCY) Loose Density (lb/LCY) Compacted Density (lb/CCY) Void Ratio Range (Bank / Loose / Compacted) Dominant Volumetric Behavior

Clean Sand & Fine Gravel 3,200 2,780 3,640 0.45 / 0.67 / 0.27 Low swell (about 15%), about 12% compaction shrinkage, rapid natural drainage

Common Earth (Sandy Loam / Silt) 2,800 2,240 3,330 0.60 / 1.00 / 0.35 Moderate swell (about 25%), about 16% compaction shrinkage, moisture sensitive

Dense Cohesive Clay (Stiff / Plastic) 3,000 2,220 3,850 0.70 / 1.30 / 0.32 High swell (about 35%), about 22% compaction shrinkage, highly cohesive

Decomposed Rock / Soft Shale 3,800 2,710 4,000 0.30 / 0.82 / 0.24 Significant swell (about 40%), about 5% compaction shrinkage, fragmentation dependent

Blasted Solid Rock (Granite / Basalt) 4,500 2,700 3,750 0.15 / 0.92 / 0.38 Extreme swell (about 67% here), net permanent swell in fill (about 1.2 CCY per BCY)

Notice that while common earth, sand, and clay exhibit net shrinkage (meaning Compacted Cubic Yards are smaller than Bank Cubic Yards), blasted hard rock behaves differently. When solid rock with an in-situ void ratio of 0.15 is blasted into irregular boulders and fractured rubble, it swells by 50% to 70%. When placed in rock-fill embankments and rolled with heavy vibratory compactors, the angular, interlocking stone fragments cannot be recompressed back to the zero-void monolithic state of solid bedrock. Consequently, blasted rock in compacted fill exhibits permanent net swell, meaning 1.0 BCY of solid bedrock yields 1.20 to 1.35 CCY of rock embankment.

Mass-Volume Conversion Fundamentals in Earthmoving

Converting between linear jobsite measurements, cubic feet, cubic yards, and total project tonnage represents the baseline mathematical skill for heavy equipment personnel:

Linear to Volumetric Conversion : Jobsite dimensions are measured in feet and inches. Because 1 yard equals 3 feet, 1 cubic yard equals a three-dimensional cube measuring 3 feet by 3 feet by 3 feet, or exactly 27 cubic feet: 1 cu yd = 3 ft × 3 ft × 3 ft = 27 cu ft 1\text{ cu yd} = 3\text{ ft} \times 3\text{ ft} \times 3\text{ ft} = 27\text{ cu ft} 1 cu yd = 3 ft × 3 ft × 3 ft = 27 cu ft To calculate the volume of any rectangular excavation in cubic yards, multiply length by width by depth (all in feet) and divide by 27: Volume (cu yd) = Length (ft) × Width (ft) × Depth (ft) 27 \text{Volume (cu yd)} = \frac{\text{Length (ft)} \times \text{Width (ft)} \times \text{Depth (ft)}}{27} Volume (cu yd) = 27 Length (ft) × Width (ft) × Depth (ft) ​

Volume to Weight (Gravimetric) Conversion : Haul trucks, public road bridges, and lowboy trailers are limited by strict legal weight limits. Converting volumetric cubic yards to total payload mass requires multiplying volume by unit weight and converting to standard short tons (2,000 pounds per ton): Total Weight (lb) = Volume (cu yd) × Density (lb/cu yd) \text{Total Weight (lb)} = \text{Volume (cu yd)} \times \text{Density (lb/cu yd)} Total Weight (lb) = Volume (cu yd) × Density (lb/cu yd) Total Weight (tons) = Total Weight (lb) 2,000 lb/ton \text{Total Weight (tons)} = \frac{\text{Total Weight (lb)}}{2{,}000\text{ lb/ton}} Total Weight (tons) = 2 , 000 lb/ton Total Weight (lb) ​

Practical Job-Site Scenario: Mass Excavation & Volumetric Tracking

Consider an industrial foundation project where an earthmoving contractor must excavate a basement and footing pad measuring 180 feet in length, 120 feet in width, and 15 feet in vertical depth. The native geotechnical profile consists of undisturbed, stiff sandy clay with an in-situ bank density of 2,970 lb/BCY, an excavated loose density of 2,285 lb/LCY (a 30% swell factor), and an engineered fill compacted density of 3,400 lb/CCY.

The project manager must track this material through its complete cycle:

Step 1: Calculate In-Situ Bank Volume (BCY) : Cubic Feet = 180 ft × 120 ft × 15 ft = 324,000 cu ft \text{Cubic Feet} = 180\text{ ft} \times 120\text{ ft} \times 15\text{ ft} = 324{,}000\text{ cu ft} Cubic Feet = 180 ft × 120 ft × 15 ft = 324 , 000 cu ft Bank Volume (BCY) = 324,000 cu ft 27 cu ft/cu yd = 12,000 BCY \text{Bank Volume (BCY)} = \frac{324{,}000\text{ cu ft}}{27\text{ cu ft/cu yd}} = 12{,}000\text{ BCY} Bank Volume (BCY) = 27 cu ft/cu yd 324 , 000 cu ft ​ = 12 , 000 BCY

Step 2: Calculate Loose Volume for Haul Fleet Dispatching (LCY) :

With a 30% swell factor, each bank cubic yard expands into 1.30 loose cubic yards: Loose Volume (LCY) = 12,000 BCY × 1.30 = 15,600 LCY \text{Loose Volume (LCY)} = 12{,}000\text{ BCY} \times 1.30 = 15{,}600\text{ LCY} Loose Volume (LCY) = 12 , 000 BCY × 1.30 = 15 , 600 LCY If the estimator mistakenly dispatched haul trucks based on the 12,000 BCY figure, the jobsite would face a shortage of 3,600 cubic yards of hauling capacity, halting the excavators and creating costly project delays.

Step 3: Calculate Total Gravimetric Tonnage to be Hauled : Total Mass = 15,600 LCY × 2,285 lb/LCY = 35,646,000 lb \text{Total Mass} = 15{,}600\text{ LCY} \times 2{,}285\text{ lb/LCY} = 35{,}646{,}000\text{ lb} Total Mass = 15 , 600 LCY × 2 , 285 lb/LCY = 35 , 646 , 000 lb Total Mass (tons) = 35,646,000 lb 2,000 lb/ton = 17,823 tons \text{Total Mass (tons)} = \frac{35{,}646{,}000\text{ lb}}{2{,}000\text{ lb/ton}} = 17{,}823\text{ tons} Total Mass (tons) = 2 , 000 lb/ton 35 , 646 , 000 lb ​ = 17 , 823 tons Verifying mass conservation using bank properties confirms the calculation: 12,000 BCY × 2,970 lb/BCY = 35,640,000 lb ≈ 17,820 tons 12{,}000\text{ BCY} \times 2{,}970\text{ lb/BCY} = 35{,}640{,}000\text{ lb} \approx 17{,}820\text{ tons} 12 , 000 BCY × 2 , 970 lb/BCY = 35 , 640 , 000 lb ≈ 17 , 820 tons .

Step 4: Calculate Compacted Fill Equivalent (CCY) :

If this excavated clay is hauled to an adjacent structural embankment where it is compacted to 3,400 lb/CCY dry density: Compacted Fill (CCY) = 35,640,000 lb 3,400 lb/CCY = 10,482 CCY \text{Compacted Fill (CCY)} = \frac{35{,}640{,}000\text{ lb}}{3{,}400\text{ lb/CCY}} = 10{,}482\text{ CCY} Compacted Fill (CCY) = 3 , 400 lb/CCY 35 , 640 , 000 lb ​ = 10 , 482 CCY The original 12,000 BCY shrinks into 10,482 CCY in the finished structural embankment—a volumetric reduction of 12.6% relative to the cut.