Study guide
20.6 Conventional (Sit-Down Counterbalanced) Forklifts
NCCER Heavy Equipment Operations Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: NCCER Credentials, Trade Orientation, Safety & Equipment Classification
1.1 NCCER Heavy Equipment Operations Credentials, Curriculum & Assessments 1.2 Heavy Equipment Industry & Operator Responsibilities 1.3 OSHA & MSHA Regulatory Standards (29 CFR 1926 & 30 CFR) 1.4 Machine Safety Systems: ROPS, FOPS, Seatbelts & Interlocks 1.5 Classifying Heavy Equipment: Machine Families, Mining Machines, Drive Systems & Hydraulics
2 Chapter 2: Pre-Operation Inspection & Preventative Maintenance
2.1 Walk-Around Inspection Procedures & Daily Checklists 2.2 Fluid Levels, Hydraulic Inspection & Filter Maintenance 2.3 Undercarriage, Tires, Tracks & Ground Engaging Tools (GET) 2.4 Engine Systems, Startup & Warm-Up, and Hybrid and Electric Equipment Readiness
3 Chapter 3: Safe Operating Practices & Site Hazards
3.1 Mounting, Dismounting (Three-Point Contact) & Cab Safety 3.2 Electrical Power Line Clearances & Overhead Hazards 3.3 Blind Spots, Swing Radii, Spotters & Hand Signals
4 Chapter 4: Refueling, Parking, Shutdown & Equipment Transport
4.1 Engine Cooldown, Safe Parking & Lockout/Tagout Procedures 4.2 Fueling Safety, Fire Prevention & Environmental Controls 4.3 Heavy Equipment Transport, Rigging & Securement / Tie-Down
5 Chapter 5: Excavator Types, Components & Hydraulics
5.1 Excavator Classifications, Tracked vs. Wheeled Configurations 5.2 House, Boom, Stick, Bucket & Hydraulic Flow Systems 5.3 Quick-Couplers, Attachments & Operational Safety
6 Chapter 6: Excavator Operations, Trenching & Lifting
6.1 Excavator Positioning, Travel & Stable Working Platforms 6.2 Trenching Techniques, Bench Cutting & Production Digging 6.3 Lifting Operations, Rigging Capacities & Load Charts
7 Chapter 7: Backhoe Loader Components & Controls
7.1 Backhoe Loader Anatomy: Loader End vs. Backhoe End 7.2 Operator Station, Pilot vs. Wobble Stick Controls & Instruments 7.3 Stabilizer Deployment, Machine Levelling & Setup on Slopes
8 Chapter 8: Backhoe Loader Operational Techniques
8.1 Backhoe Digging, Spoiling, Truck Loading & Cycle Efficiency 8.2 Front-End Loader Operations with Backhoe Loaders 8.3 Backhoe Road Travel, Transport Safety & Boom Locking
9 Chapter 9: Bulldozer Types, Powertrains & Blade Configurations
9.1 Crawler Dozer Classifications, Undercarriages & Ground Pressure 9.2 Drivetrains: Torque Converters, Powershift & Hydrostatic Drives 9.3 Blade Types: Straight (S), Universal (U), Semi-Universal (SU) & Angle Blades
10 Chapter 10: Bulldozer Earthmoving Operations
10.1 Straight Dozing, Slot Dozing & Production Pushing 10.2 Push-Loading Scrapers & Multi-Machine Earthmoving 10.3 Stockpiling, Berm Construction & Material Spreading
11 Chapter 11: Dozer Slope Work, Ripping & Clearing
11.1 Sidehill Operations, Working Up and Down Steep Slopes 11.2 Ripper Attachments: Single Shank, Multi-Shank & Ripping Techniques 11.3 Site Clearing, Tree Felling & Stumping Precautions
12 Chapter 12: Wheel Loaders & Track Loaders
12.1 Wheel Loader Anatomy, Articulated Steering & Z-Bar Linkage 12.2 Loading Patterns: V-Pattern, I-Pattern & Truck Placement 12.3 Excavation, Stockpile Management & Carry Operations
13 Chapter 13: Motor Grader Anatomy & Blade Geometry
13.1 Motor Grader Components: Tandem Drive, Articulation & Front Wheel Lean 13.2 Moldboard Mechanics: Pitch, Angle, Lift & Side-Shift 13.3 Grader Safety, Operating Speeds & Reversing Precautions
14 Chapter 14: Motor Grader Operations & Finish Grading
14.1 Ditching, Backsloping & Windrowing Techniques 14.2 Roadway Crown, Cross-Slope & Superelevation Creation 14.3 Fine Grading Tolerances, Blue Tops & Final Trimming
15 Chapter 15: Earthmoving Principles, Excavation Math, Soils & Planning
15.1 Soil Mechanics: Bank, Loose & Compacted Cubic Yards 15.2 Swell, Shrinkage & Load Factor Calculations 15.3 Slope Ratios, Percent Grade & Elevation Calculations 15.4 Soil Classification Systems (USCS & AASHTO) and Soil Effects on Equipment 15.5 Earthmoving Planning & Soil Stabilization Methods
16 Chapter 16: Civil Drawings, Staking, Layout, Pipe Laying & Machine Control
16.1 Reading Civil Engineering Site Plans, Contours & Profiles 16.2 Construction Stakes: Stationing, Offset, Cut & Fill Stakes 16.3 Laser Levels, GNSS/GPS Machine Control & 3D Telematics 16.4 Foundation Layout & Pipe Laying
17 Chapter 17: Soil Compaction Equipment & Methods
17.1 Principles of Soil Compaction & Optimum Moisture Content (Proctor Test) 17.2 Roller Types: Smooth Drum, Padfoot / Sheepsfoot, Pneumatic & Tamping 17.3 Lift Thickness, Pass Overlap & In-Place Density Testing
18 Chapter 18: OSHA 1926 Subpart P: Soil Classification & Cave-In Protection
18.1 OSHA Soil Mechanics: Type A, Type B & Type C Classification 18.2 Cave-In Protection Systems: Sloping, Benching, Shoring & Shielding 18.3 Duties of the OSHA Competent Person & Daily Trench Inspections
19 Chapter 19: Excavation Site Hazards & Underground Utilities
19.1 Utility Locating (811 Call Before You Dig) & Potholing Procedures 19.2 Safe Access, Egress (Ladders/Ramps) & Hazardous Atmospheres 19.3 Surface Water Diversion, Dewatering & Backfilling Requirements
20 Chapter 20: Specialized Equipment: Compact Loaders, Forklifts, Haulers & Tractors
20.1 Skid-Steer Loaders & Compact Track Loaders (CTLs): Controls & Stability 20.2 Rough-Terrain Forklifts & Telehandlers: Stability Triangle & Load Charts 20.3 Scrapers, Off-Road Articulated Dump Trucks & Utility Tractors 20.4 Dump Trucks: On-Road and Off-Road Operation 20.5 Utility Tractors: ROPS, Overturn Prevention, Ballast & Implement Hookup 20.6 Conventional (Sit-Down Counterbalanced) Forklifts
20.6 Conventional (Sit-Down Counterbalanced) Forklifts
Key Takeaways Explain This Topic AI
OSHA 1910.178(l), applied to construction by 1926.602(d), requires training, a workplace evaluation before operating, and a performance evaluation at least once every three years.
Refresher training is required after unsafe operation, an accident or near miss, a poor evaluation, assignment to a different type of truck, or a change in workplace conditions.
A forklift is unattended when the operator is 25 feet or more away or out of view; the forks must then be fully lowered, controls neutralized, power shut off, and brakes set.
On grades over 10 percent, a loaded forklift travels with the load upgrade; at cross aisles and blind spots, the operator slows and sounds the horn.
Trucks must be examined before being placed in service at least daily, or after each shift in round-the-clock use, and defects must be corrected first.
Last updated: October 2026
- Conventional (Sit-Down Counterbalanced) Forklifts
- Where Conventional Forklifts Fit
A conventional forklift is a sit-down, counterbalanced lift truck with a vertical mast. The counterweight at the rear balances the load on the forks. These trucks work on smooth, firm surfaces such as warehouse floors, loading docks, and paved material yards. Rough-terrain forklifts and telehandlers (Section 20.2) are built for unimproved jobsite ground.
The Industrial Truck Association (ITA), used by OSHA, sorts powered industrial trucks into seven classes:
- Class Description
- I Electric motor rider trucks, including sit-down counterbalanced electric forklifts
- II Electric motor narrow-aisle trucks
- III Electric motor hand and hand-rider trucks
- IV Internal combustion trucks with cushion (solid) tires, for smooth indoor floors
- V Internal combustion trucks with pneumatic tires, for indoor and outdoor yards
- VI Electric and internal combustion tractors
- VII Rough-terrain forklifts
- Capacity and the Data Plate
The data plate shows the truck's rated capacity at a stated load center , usually 24 inches from the fork face. It also shows maximum lift height and any capacity reductions for attachments. In construction, 1926.602(c)(1) requires the rated capacity to be posted where the operator can see it and prohibits exceeding it. Modifications that affect capacity or safe operation require the manufacturer's written approval. Moving the load farther out, raising it higher, or tilting the mast forward reduces the safe capacity. The stability triangle described in Section 20.2 applies to conventional forklifts too.
Training and Evaluation
OSHA 1910.178(l) sets the training rules, and 1926.602(d) applies the same requirements to construction work.
Before operating: training must combine formal instruction, practical training, and an evaluation of the operator's performance in the workplace.
Refresher training is required when the operator:
Has been observed operating unsafely.
Has been involved in an accident or near-miss incident.
Received an evaluation showing unsafe operation.
Is assigned to a different type of truck.
Faces a change in workplace conditions that could affect safe operation.
Evaluation at least once every three years .
Certification: the employer certifies that each operator has been trained and evaluated, recording the operator's name, the training and evaluation dates, and who performed the training or evaluation.
OSHA does not issue forklift licenses. Training is site- and truck-specific and is certified by the employer.
Daily Examination
Under 1910.178(q)(7), trucks must be examined before being placed in service and must not be used if a condition affects safety. The examination is required at least daily , or after each shift for round-the-clock use. Typical checks:
Forks, mast, chains, and the carriage.
Hydraulic leaks, tires, brakes, steering, and the horn.
Lights, seat belt, overhead guard, and data plate.
Fuel or battery condition.
Travel Rules from 1910.178(n)
Obey plant speed limits and keep about three truck lengths behind the truck ahead.
Do not pass other trucks traveling the same direction at intersections or blind spots.
Slow down and sound the horn at cross aisles and wherever vision is blocked.
If the load blocks the forward view, travel with the load trailing , which means driving in reverse.
Cross railroad tracks diagonally where possible, and never park within 8 feet of the center of the tracks.
On grades over 10 percent , drive loaded trucks with the load upgrade . On all grades, tilt the load back and raise it only enough to clear the surface.
No riders unless a safe place to ride is provided, and no one may stand or pass under raised forks.
Parking and Leaving the Truck
Situation Requirement
Unattended: operator 25 feet or more away, or the truck out of view Forks fully lowered, controls neutralized, power off, brakes set; wheels blocked on an incline
Operator dismounted within 25 feet with the truck in view Forks fully lowered, controls neutralized, brakes set
Loading Trucks, Trailers, and Railcars
Under 1910.178(k)(1), the brakes of a highway truck must be set and wheel chocks placed under the rear wheels before a forklift drives onto it.
Railcars need wheel stops or other positive protection, and an uncoupled semitrailer may need fixed jacks to prevent upending.
Check the trailer floor and the dock board's rated capacity before driving across.
Battery Charging and Propane Cylinders
Battery charging (1910.178(g)):
Charge only in designated areas.
The area needs facilities for flushing and neutralizing spilled electrolyte, fire protection, and protection for chargers from truck damage.
Provide ventilation to disperse gas from charging batteries.
No smoking, open flames, sparks, or arcs in the charging area.
Keep tools and metal objects off uncovered batteries.
When mixing electrolyte, pour acid into water, never water into acid.
Changing a propane cylinder (a typical manufacturer procedure):
Close the cylinder service valve and run the engine until it stops.
Wear gloves and eye protection, because liquid propane can cause frostbite.
Check the coupling seal and set the new cylinder on its locating pin.
Tighten the coupling and open the valve slowly.
Check for leaks before restarting.