Study guide
20.4 Dump Trucks: On-Road and Off-Road Operation
NCCER Heavy Equipment Operations Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: NCCER Credentials, Trade Orientation, Safety & Equipment Classification
1.1 NCCER Heavy Equipment Operations Credentials, Curriculum & Assessments 1.2 Heavy Equipment Industry & Operator Responsibilities 1.3 OSHA & MSHA Regulatory Standards (29 CFR 1926 & 30 CFR) 1.4 Machine Safety Systems: ROPS, FOPS, Seatbelts & Interlocks 1.5 Classifying Heavy Equipment: Machine Families, Mining Machines, Drive Systems & Hydraulics
2 Chapter 2: Pre-Operation Inspection & Preventative Maintenance
2.1 Walk-Around Inspection Procedures & Daily Checklists 2.2 Fluid Levels, Hydraulic Inspection & Filter Maintenance 2.3 Undercarriage, Tires, Tracks & Ground Engaging Tools (GET) 2.4 Engine Systems, Startup & Warm-Up, and Hybrid and Electric Equipment Readiness
3 Chapter 3: Safe Operating Practices & Site Hazards
3.1 Mounting, Dismounting (Three-Point Contact) & Cab Safety 3.2 Electrical Power Line Clearances & Overhead Hazards 3.3 Blind Spots, Swing Radii, Spotters & Hand Signals
4 Chapter 4: Refueling, Parking, Shutdown & Equipment Transport
4.1 Engine Cooldown, Safe Parking & Lockout/Tagout Procedures 4.2 Fueling Safety, Fire Prevention & Environmental Controls 4.3 Heavy Equipment Transport, Rigging & Securement / Tie-Down
5 Chapter 5: Excavator Types, Components & Hydraulics
5.1 Excavator Classifications, Tracked vs. Wheeled Configurations 5.2 House, Boom, Stick, Bucket & Hydraulic Flow Systems 5.3 Quick-Couplers, Attachments & Operational Safety
6 Chapter 6: Excavator Operations, Trenching & Lifting
6.1 Excavator Positioning, Travel & Stable Working Platforms 6.2 Trenching Techniques, Bench Cutting & Production Digging 6.3 Lifting Operations, Rigging Capacities & Load Charts
7 Chapter 7: Backhoe Loader Components & Controls
7.1 Backhoe Loader Anatomy: Loader End vs. Backhoe End 7.2 Operator Station, Pilot vs. Wobble Stick Controls & Instruments 7.3 Stabilizer Deployment, Machine Levelling & Setup on Slopes
8 Chapter 8: Backhoe Loader Operational Techniques
8.1 Backhoe Digging, Spoiling, Truck Loading & Cycle Efficiency 8.2 Front-End Loader Operations with Backhoe Loaders 8.3 Backhoe Road Travel, Transport Safety & Boom Locking
9 Chapter 9: Bulldozer Types, Powertrains & Blade Configurations
9.1 Crawler Dozer Classifications, Undercarriages & Ground Pressure 9.2 Drivetrains: Torque Converters, Powershift & Hydrostatic Drives 9.3 Blade Types: Straight (S), Universal (U), Semi-Universal (SU) & Angle Blades
10 Chapter 10: Bulldozer Earthmoving Operations
10.1 Straight Dozing, Slot Dozing & Production Pushing 10.2 Push-Loading Scrapers & Multi-Machine Earthmoving 10.3 Stockpiling, Berm Construction & Material Spreading
11 Chapter 11: Dozer Slope Work, Ripping & Clearing
11.1 Sidehill Operations, Working Up and Down Steep Slopes 11.2 Ripper Attachments: Single Shank, Multi-Shank & Ripping Techniques 11.3 Site Clearing, Tree Felling & Stumping Precautions
12 Chapter 12: Wheel Loaders & Track Loaders
12.1 Wheel Loader Anatomy, Articulated Steering & Z-Bar Linkage 12.2 Loading Patterns: V-Pattern, I-Pattern & Truck Placement 12.3 Excavation, Stockpile Management & Carry Operations
13 Chapter 13: Motor Grader Anatomy & Blade Geometry
13.1 Motor Grader Components: Tandem Drive, Articulation & Front Wheel Lean 13.2 Moldboard Mechanics: Pitch, Angle, Lift & Side-Shift 13.3 Grader Safety, Operating Speeds & Reversing Precautions
14 Chapter 14: Motor Grader Operations & Finish Grading
14.1 Ditching, Backsloping & Windrowing Techniques 14.2 Roadway Crown, Cross-Slope & Superelevation Creation 14.3 Fine Grading Tolerances, Blue Tops & Final Trimming
15 Chapter 15: Earthmoving Principles, Excavation Math, Soils & Planning
15.1 Soil Mechanics: Bank, Loose & Compacted Cubic Yards 15.2 Swell, Shrinkage & Load Factor Calculations 15.3 Slope Ratios, Percent Grade & Elevation Calculations 15.4 Soil Classification Systems (USCS & AASHTO) and Soil Effects on Equipment 15.5 Earthmoving Planning & Soil Stabilization Methods
16 Chapter 16: Civil Drawings, Staking, Layout, Pipe Laying & Machine Control
16.1 Reading Civil Engineering Site Plans, Contours & Profiles 16.2 Construction Stakes: Stationing, Offset, Cut & Fill Stakes 16.3 Laser Levels, GNSS/GPS Machine Control & 3D Telematics 16.4 Foundation Layout & Pipe Laying
17 Chapter 17: Soil Compaction Equipment & Methods
17.1 Principles of Soil Compaction & Optimum Moisture Content (Proctor Test) 17.2 Roller Types: Smooth Drum, Padfoot / Sheepsfoot, Pneumatic & Tamping 17.3 Lift Thickness, Pass Overlap & In-Place Density Testing
18 Chapter 18: OSHA 1926 Subpart P: Soil Classification & Cave-In Protection
18.1 OSHA Soil Mechanics: Type A, Type B & Type C Classification 18.2 Cave-In Protection Systems: Sloping, Benching, Shoring & Shielding 18.3 Duties of the OSHA Competent Person & Daily Trench Inspections
19 Chapter 19: Excavation Site Hazards & Underground Utilities
19.1 Utility Locating (811 Call Before You Dig) & Potholing Procedures 19.2 Safe Access, Egress (Ladders/Ramps) & Hazardous Atmospheres 19.3 Surface Water Diversion, Dewatering & Backfilling Requirements
20 Chapter 20: Specialized Equipment: Compact Loaders, Forklifts, Haulers & Tractors
20.1 Skid-Steer Loaders & Compact Track Loaders (CTLs): Controls & Stability 20.2 Rough-Terrain Forklifts & Telehandlers: Stability Triangle & Load Charts 20.3 Scrapers, Off-Road Articulated Dump Trucks & Utility Tractors 20.4 Dump Trucks: On-Road and Off-Road Operation 20.5 Utility Tractors: ROPS, Overturn Prevention, Ballast & Implement Hookup 20.6 Conventional (Sit-Down Counterbalanced) Forklifts
20.4 Dump Trucks: On-Road and Off-Road Operation
Key Takeaways Explain This Topic AI
A single dump truck with a gross vehicle weight rating of 26,001 pounds or more requires at least a Class B commercial driver's license; a truck towing a trailer over 10,000 pounds requires Class A.
OSHA 1926.601(b)(14) requires a check at the start of each shift of brakes, tires, horn, steering, coupling devices, seat belts, operating controls, and safety devices.
Dump bodies must have a permanently attached, lockable support so the body cannot drop during maintenance or inspection (1926.601(b)(10)).
Most dump-truck rollovers happen when the body is raised on uneven or soft ground, with the truck not straight, or with a load that sticks in the body.
A truck with an obstructed rear view may back only with a reverse alarm audible above surrounding noise or when an observer signals that it is safe (1926.601(b)(4)).
Last updated: October 2026
- Dump Trucks: On-Road and Off-Road Operation
- Types of Dump Trucks
- Type Description Typical use
- Single-axle dump One rear axle; smallest highway dump truck Small loads, landscaping, municipal work
- Tandem-axle dump Two rear drive axles The most common construction dump truck
- Tri-axle or quad-axle dump Adds liftable ("drop") axles to spread weight Heavier legal loads on highways
- Super dump Adds a trailing booster axle behind the body Maximum legal payload where states allow
Transfer dump Truck pulls a trailer whose body rolls forward into the truck body to unload Long hauls with high payload
End-dump trailer Tractor-trailer with a tall hoisted body Bulk aggregate; the highest rollover risk when raised
Bottom-dump (belly) trailer Gates open under the trailer to drop material in a windrow Spreading aggregate on roadbeds
- Side-dump trailer Body tips sideways Fast dumping into trenches or over embankments
- Articulated dump truck (ADT) 6x6 off-road hauler with an oscillating hitch Soft or rough off-road hauls
- Rigid-frame haul truck One-piece frame, very large payloads Quarries, mines, and large earthmoving jobs
Section 20.3 covers ADTs and rigid haulers in detail. This section focuses on practices that apply to every dump truck.
Licensing and Weight Limits
Under federal CDL rules (49 CFR Part 383):
Class B covers a single vehicle with a gross vehicle weight rating (GVWR) of 26,001 pounds or more , which includes most tandem dump trucks.
Class A covers combinations with a gross combination weight rating of 26,001 pounds or more when the towed unit's GVWR exceeds 10,000 pounds , such as end-dump and bottom-dump trailers.
CDL drivers are also subject to federal drug and alcohol testing.
On the Interstate system, federal limits are 20,000 pounds on a single axle, 34,000 pounds on a tandem axle, and 80,000 pounds gross, subject to the federal bridge formula. States set limits for other roads and issue overweight permits. Lift axles must be lowered as state rules require to spread the load. Overloading lengthens stopping distance, overheats brakes, and damages tires and roads.
Inspection Before Each Shift
OSHA 1926.601(b)(14) requires that every vehicle on a construction site be checked at the beginning of each shift, including service brakes and trailer brake connections, the parking brake, emergency stopping system, tires, horn, steering, coupling devices, seat belts, operating controls, and safety devices. Defects must be corrected before the vehicle goes into service. Highway drivers must also be satisfied that the vehicle is safe before driving and review the last driver vehicle inspection report (49 CFR 396.13).
Dump-specific checks include:
Hoist cylinder, hoses, and body hinge pins.
The PTO and hoist control, including the latch that prevents accidental tripping.
Tailgate latches, chains, and hinges.
The body-up warning light or alarm.
The body support prop.
Tarp system, mirrors, lights, and the backup alarm.
Loading
Position the truck where the loader or excavator operator can load it without swinging over people.
OSHA 1926.651(e) requires employees to stand away from vehicles being loaded or unloaded. The driver may stay in the cab only if the truck has a cab shield or canopy adequate to protect against falling material (1926.601(b)(6)).
Load evenly, centered side to side, and not above the sideboards.
Federal rules require loose cargo to be loaded so it does not leak, spill, blow, or fall from the vehicle (49 CFR 393.100), and many states require tarps.
Dumping Safely
Choose firm, level ground. Soft fill can give way under one rear wheel as the body rises.
Line up straight. Dump with the truck straight, and with a trailer in line with its tractor.
Look up. Check for power lines, trees, and structures before raising the body. Equipment near power lines must keep at least 10 feet of clearance from lines rated 50 kV or less, with more for higher voltages (1926.600(a)(6)).
Watch for sticky or frozen loads. Material that hangs up in the front of a raised body puts a heavy weight high and forward and can tip the truck. Do not rock or jerk the truck to free it; lower the body and get the load loosened.
Consider wind and slope. A crosswind on a raised end-dump body or a side slope can push the truck over.
Keep the tailgate area clear. Tailgate trip handles must let the operator stay in the clear while dumping (1926.601(b)(12)). No one should stand behind or beside the truck during dumping.
Lower the body fully and disengage the PTO before driving away. A raised body can strike overhead lines and structures.
When spreading material, release it at a slow, steady speed with the tailgate set as the job requires. At fill edges and stockpiles, keep the required setback from the crest or dump against a berm.
Backing and Spotters
Under 1926.601(b)(4), a vehicle with an obstructed rear view may back up only if it has a reverse alarm audible above the surrounding noise or an observer signals that it is safe. Good backing practice includes:
Use one designated spotter, agreed hand signals, and eye contact.
If you lose sight of the spotter, stop.
Spotters stay out of the truck's path and away from the space between the truck and fixed objects.
Follow the site's internal traffic control plan, which separates trucks from workers on foot.
Working Under a Raised Body
1926.601(b)(10) requires trucks with dump bodies to have a positive means of support, permanently attached and capable of being locked in position , to prevent accidental lowering during maintenance or inspection. Lever controls for hoisting or dumping must have a latch to prevent accidental starting or tripping (1926.601(b)(11)). Never rely on the hoist cylinder alone. Place and lock the body prop, shut down the engine, and lock out the controls before anyone reaches under the body.