Study guide
1.2 The Nine Content Domains: Item Counts and a Study Plan
NCCER Industrial Maintenance Mechanic Exam
Track your progress as you read
Finished sections get a check mark.
1 The NCCER Industrial Maintenance Mechanic Assessment
1.1 The IMM Journey-Level Credential and Assessment Specification 1.2 The Nine Content Domains: Item Counts and a Study Plan
2 Industrial Maintenance Mechanic Fundamentals
2.1 Safety Programs, PPE, and Hazard Communication 2.2 Hazardous Energy Control: Lockout/Tagout and Confined Space Entry 2.3 Tools of the Trade: Hand and Power Tools 2.4 Oxyfuel Cutting: Equipment, Safe Setup, and Cutting Practice 2.5 Ferrous Metal Piping Practices: Cutting, Threading, and Joining
3 Rigging and Mobile Equipment
3.1 Slings, Rigging Hardware, and Inspection Criteria 3.2 Load Weight, Center of Gravity, Sling Angle, and Hand Signals 3.3 Mobile and Support Equipment: Forklifts, Aerial Lifts, and Mobile Cranes
4 Craft Mathematics, Layout, and Precision Measurement
4.1 Craft-Related Mathematics: Fractions, Units, Area, and Volume 4.2 Advanced Trade Math: Right Triangles, Trigonometry, and Pipe Offsets 4.3 Basic Layout: Squaring, Leveling, and Transferring Elevations 4.4 Precision Measuring Tools: Micrometers, Verniers, and Dial Indicators 4.5 Gauges, Tolerances and Fits, and Torque Measurement
5 Construction Drawings and Blueprint Reading
5.1 Reading Construction Drawings: Views, Lines, Scales, and the Title Block 5.2 Orthographic, Isometric, Arrangement, and Foundation Drawings 5.3 Advanced Blueprint Reading: P&IDs, Instrument Tags, and Welding Symbols
6 Valves, Packing, and Mechanical Seals
6.1 Valve Types and Service Selection 6.2 Valve Construction, Markings, Pressure Classes, and Actuators 6.3 Removing and Installing Valves: Flange Bolting and Torque Sequence 6.4 Valve Maintenance: Packing, Stuffing Boxes, Gaskets, and O-Rings 6.5 Hydrostatic and Pneumatic Testing of Piping and Equipment 6.6 Mechanical Seals: Components, Types, and Installation
7 Bearings, Lubrication, and Couplings
7.1 Bearing Types, Designations, and Selection 7.2 Bearing Lubrication, Handling, and Failure Analysis 7.3 Removing and Installing Bearings: Fits, Heating, and Mounting 7.4 Couplings: Types, Selection, and Installation
8 Pumps, Baseplates, and Mechanical Drives
8.1 Pumps and Drivers: Centrifugal and Positive Displacement 8.2 Setting Baseplates and Soleplates: Leveling, Anchoring, and Grouting 8.3 Prealignment: Soft Foot, Runout, Pipe Strain, and Shims 8.4 Installing Belt and Chain Drives
9 Shaft Alignment: Conventional, Reverse, and Laser
9.1 Conventional Rim-and-Face Dial Indicator Alignment 9.2 Reverse Dial Indicator Alignment 9.3 Laser Shaft Alignment Systems
10 Maintenance Troubleshooting: Method, Pumps, and Gearboxes
10.1 Systematic Troubleshooting and Root Cause Analysis 10.2 Troubleshooting and Repairing Pumps 10.3 Troubleshooting and Repairing Gearboxes
11 Steam Systems, Boilers, and Process Vessels
11.1 Low-Pressure Steam Systems, Traps, and Condensate Return 11.2 High-Pressure Steam Generation and Boiler Auxiliaries 11.3 Distillation Towers, Vessels, and Internals
12 Compressors and Pneumatic Systems
12.1 Air Compressor Types, Operation, and Maintenance 12.2 Compressed Air Treatment, Storage, and Distribution 12.3 FRL Units, Pneumatic Valves, Actuators, and Speed Control
1.2 The Nine Content Domains: Item Counts and a Study Plan
Key Takeaways Explain This Topic AI
The 115 IMM items are divided across nine published content domains, each referenced to specific 3rd edition curriculum modules.
Valves and Seals and Steam Systems tie for the largest share at 16 items each, followed by Math and Measurements and Maintenance and Troubleshooting at 15 items each.
Construction Drawings is the smallest domain at 7 items, and Rigging and Mobile Equipment is next smallest at 9 items.
Piping, valves, and seals together with steam systems account for 32 of 115 items, so process piping knowledge is the single largest block on the exam.
Study time should be allocated by item count, not by how interesting or familiar a domain feels.
Last updated: September 2026
The published domain table
The IMM specification lists its written assessment contents as nine content domains. Each domain names the 3rd edition curriculum modules it draws from and the exact number of items it contributes. The counts sum to 115.
# Content domain Items Share Referenced modules
1 Industrial Maintenance Mechanic Fundamentals 14 12.2% 00101 Basic Safety; 32102 Tools of the Trade; 32104 Oxyfuel Cutting; 32204 Introduction to Ferrous Metal Piping Practices
2 Rigging and Mobile Equipment 9 7.8% 00106 Basic Rigging; 32111 Material Handling and Hand Rigging; 32112 Mobile and Support Equipment
3 Math and Measurements 15 13.0% 32106 Craft-Related Mathematics; 32201 Basic Layout; 32301 Advanced Trade Math; 32302 Precision Measuring Tools
4 Construction Drawings 7 6.1% 32107 Construction Drawings; 32402 Advanced Blueprint Reading
5 Valves and Seals 16 13.9% 32109 Valves; 32204 Ferrous Metal Piping; 32205 Identify, Install, and Maintain Valves; 32206 Hydrostatic and Pneumatic Testing; 32308 Installing Mechanical Seals
6 Bearings and Coupling 12 10.4% 32207 Introduction to Bearings; 32303 Installing Bearings; 32304 Installing Couplings
7 Pumps, Drives, and Plates 11 9.6% 32108 Pumps and Drivers; 32305 Setting Baseplates and Prealignment; 32307 Installing Belt and Chain Drives
8 Maintenance and Troubleshooting 15 13.0% 32306 Conventional Alignment; 32404 Reverse Alignment; 32405 Laser Alignment; 32407 Troubleshooting and Repairing Pumps; 32408 Troubleshooting and Repairing Gearboxes
9 Steam Systems 16 13.9% 32208 Low-Pressure Steam Systems; 32209 High-Pressure Steam Systems and Auxiliaries; 32210 Distillation Towers and Vessels; 32403 Compressors and Pneumatic Systems
Two structural facts jump out of that table.
First, alignment is worth more than most candidates think . Domain 8 is 15 items, and three of its five modules — conventional alignment, reverse alignment, and laser alignment — are nothing but shaft alignment. Alignment alone plausibly accounts for the majority of that domain.
Second, compressors live inside the Steam Systems domain . Module 32403, Compressors and Pneumatic Systems, is grouped with the boiler and tower modules. If you skip compressors because you were studying "steam," you are leaving items on the table in the joint-largest domain.
IMM assessment items by content domain (115 total)
Converting item counts into study hours
A rational plan allocates preparation time in proportion to items, adjusted upward for topics that require procedural skill rather than recall. Math, alignment, and piping fabrication all require practice; steam system component identification is largely recall.
- Domain Items Suggested share of study time Why the adjustment
- Math and Measurements 15 16% Trig and micrometer reading must be practiced, not read
- Maintenance and Troubleshooting 15 16% Three alignment methods plus two repair modules
- Valves and Seals 16 15% Large but heavily recall-based once valve types are learned
- Steam Systems 16 14% Mostly component identification and function
- IMM Fundamentals 14 12% Safety and tools are familiar to working mechanics
- Bearings and Coupling 12 10% Fits, mounting methods, and failure patterns
- Pumps, Drives, and Plates 11 9% Grouting and prealignment procedures
- Rigging and Mobile Equipment 9 5% Well-standardized, quick to review
- Construction Drawings 7 3% Smallest domain; review symbols and views only
- The four traps in this blueprint
Treating "Fundamentals" as free points. Domain 1 includes oxyfuel cutting and ferrous pipe fabrication, not just safety. Both carry specific numbers — cutting tip sizes, drop, thread engagement — that are easy to miss.
Skipping Basic Layout. Module 32201 sits quietly inside the Math and Measurements domain. Squaring, leveling, and elevation transfer show up as applied math items.
Learning only one alignment method. Conventional, reverse, and laser alignment are three separate referenced modules. Knowing rim-and-face alone leaves two-thirds of that block uncovered.
Ignoring the calculator limitation. Every calculation in the Math and Measurements and Pumps, Drives, and Plates domains has to be workable on a basic four-function calculator with a square-root key.
How this guide is organized
Chapters 2 through 12 follow the nine domains in specification order, with alignment broken into its own chapter because of its weight. Each chapter states which modules it covers, so you can cross-check your training prescription against it after a practice attempt.
Chapter-to-domain crosswalk
Use this table to confirm you have touched every domain, and to translate a score report back into the chapters you need to reread.
- Chapter Content domain it serves Items Sections here
- 1. The NCCER IMM Assessment Orientation to the specification itself — 2
- 2. Industrial Maintenance Mechanic Fundamentals IMM Fundamentals (00101, 32102, 32104, 32204) 14 5
- 3. Rigging and Mobile Equipment Rigging and Mobile Equipment (00106, 32111, 32112) 9 3
4. Craft Mathematics, Layout, and Precision Measurement Math and Measurements (32106, 32201, 32301, 32302) 15 5
- 5. Construction Drawings and Blueprint Reading Construction Drawings (32107, 32402) 7 3
- 6. Valves, Packing, and Mechanical Seals Valves and Seals (32109, 32204, 32205, 32206, 32308) 16 6
- 7. Bearings, Lubrication, and Couplings Bearings and Coupling (32207, 32303, 32304) 12 4
- 8. Pumps, Baseplates, and Mechanical Drives Pumps, Drives, and Plates (32108, 32305, 32307) 11 4
- 9. Shaft Alignment Maintenance and Troubleshooting (32306, 32404, 32405) part of 15 3
- 10. Maintenance Troubleshooting Maintenance and Troubleshooting (32407, 32408) part of 15 3
- 11. Steam Systems, Boilers, and Process Vessels Steam Systems (32208, 32209, 32210) part of 16 3
- 12. Compressors and Pneumatic Systems Steam Systems (32403) part of 16 3
Chapters 9 and 10 split the 15-item Maintenance and Troubleshooting domain, and chapters 11 and 12 split the 16-item Steam Systems domain. Both splits are editorial, made because alignment and compressors each need room of their own; the specification groups them as shown in the right-hand column.
A six-week plan
This schedule assumes roughly eight study hours per week and front-loads the skills that need repetition.
- Week Focus Chapters Why it sits here
- 1 Fundamentals and rigging 2, 3 23 items, and the safety and tool vocabulary is used by every later chapter
2 Craft math, layout, and precision measurement 4 15 items of skill, not recall; starting early leaves five weeks of repetition
3 Drawings, then valve types and construction 5, sections 6.1–6.3 Drawings are only 7 items, so finish them fast and move into the largest domain
4 Valve maintenance, testing, seals, bearings, couplings Sections 6.4–6.6, chapter 7 Chapters 6 and 7 carry 28 items between them, and seals and bearing fits are the densest material in either
5 Pumps, baseplates, drives, and all three alignment methods 8, 9 Procedural chapters; work the dial-indicator arithmetic on paper
6 Troubleshooting, steam systems, compressors 10, 11, 12 The whole 16-item Steam Systems domain plus the two equipment-repair modules; finish on the joint-largest domain while it is freshest
Keep a short daily block for chapter 4 in every week. Thirty minutes a day on pipe offsets, micrometer readings, and unit conversions is worth more than a fourth pass through valve types, because math is the part that decays fastest and the part you cannot look up in a closed-book examination.
If you do not pass
The specification promises every candidate online access to their overall score and recommended training through their NCCER Account. Map the weak domains from that report onto the crosswalk table above, then rebuild the six-week plan with the failed domains in weeks 1 and 2 rather than restudying the whole guide evenly. Retest eligibility, waiting periods, and fees are set by your assessment center, not by the specification sheet, so confirm them locally before scheduling.