Study guide

2.5 Ferrous Metal Piping Practices: Cutting, Threading, and Joining

NCCER Industrial Maintenance Mechanic Exam

Track your progress as you read

Finished sections get a check mark.

1 The NCCER Industrial Maintenance Mechanic Assessment

1.1 The IMM Journey-Level Credential and Assessment Specification 1.2 The Nine Content Domains: Item Counts and a Study Plan

2 Industrial Maintenance Mechanic Fundamentals

2.1 Safety Programs, PPE, and Hazard Communication 2.2 Hazardous Energy Control: Lockout/Tagout and Confined Space Entry 2.3 Tools of the Trade: Hand and Power Tools 2.4 Oxyfuel Cutting: Equipment, Safe Setup, and Cutting Practice 2.5 Ferrous Metal Piping Practices: Cutting, Threading, and Joining

3 Rigging and Mobile Equipment

3.1 Slings, Rigging Hardware, and Inspection Criteria 3.2 Load Weight, Center of Gravity, Sling Angle, and Hand Signals 3.3 Mobile and Support Equipment: Forklifts, Aerial Lifts, and Mobile Cranes

4 Craft Mathematics, Layout, and Precision Measurement

4.1 Craft-Related Mathematics: Fractions, Units, Area, and Volume 4.2 Advanced Trade Math: Right Triangles, Trigonometry, and Pipe Offsets 4.3 Basic Layout: Squaring, Leveling, and Transferring Elevations 4.4 Precision Measuring Tools: Micrometers, Verniers, and Dial Indicators 4.5 Gauges, Tolerances and Fits, and Torque Measurement

5 Construction Drawings and Blueprint Reading

5.1 Reading Construction Drawings: Views, Lines, Scales, and the Title Block 5.2 Orthographic, Isometric, Arrangement, and Foundation Drawings 5.3 Advanced Blueprint Reading: P&IDs, Instrument Tags, and Welding Symbols

6 Valves, Packing, and Mechanical Seals

6.1 Valve Types and Service Selection 6.2 Valve Construction, Markings, Pressure Classes, and Actuators 6.3 Removing and Installing Valves: Flange Bolting and Torque Sequence 6.4 Valve Maintenance: Packing, Stuffing Boxes, Gaskets, and O-Rings 6.5 Hydrostatic and Pneumatic Testing of Piping and Equipment 6.6 Mechanical Seals: Components, Types, and Installation

7 Bearings, Lubrication, and Couplings

7.1 Bearing Types, Designations, and Selection 7.2 Bearing Lubrication, Handling, and Failure Analysis 7.3 Removing and Installing Bearings: Fits, Heating, and Mounting 7.4 Couplings: Types, Selection, and Installation

8 Pumps, Baseplates, and Mechanical Drives

8.1 Pumps and Drivers: Centrifugal and Positive Displacement 8.2 Setting Baseplates and Soleplates: Leveling, Anchoring, and Grouting 8.3 Prealignment: Soft Foot, Runout, Pipe Strain, and Shims 8.4 Installing Belt and Chain Drives

9 Shaft Alignment: Conventional, Reverse, and Laser

9.1 Conventional Rim-and-Face Dial Indicator Alignment 9.2 Reverse Dial Indicator Alignment 9.3 Laser Shaft Alignment Systems

10 Maintenance Troubleshooting: Method, Pumps, and Gearboxes

10.1 Systematic Troubleshooting and Root Cause Analysis 10.2 Troubleshooting and Repairing Pumps 10.3 Troubleshooting and Repairing Gearboxes

11 Steam Systems, Boilers, and Process Vessels

11.1 Low-Pressure Steam Systems, Traps, and Condensate Return 11.2 High-Pressure Steam Generation and Boiler Auxiliaries 11.3 Distillation Towers, Vessels, and Internals

12 Compressors and Pneumatic Systems

12.1 Air Compressor Types, Operation, and Maintenance 12.2 Compressed Air Treatment, Storage, and Distribution 12.3 FRL Units, Pneumatic Valves, Actuators, and Speed Control

2.5 Ferrous Metal Piping Practices: Cutting, Threading, and Joining

Key Takeaways Explain This Topic AI

NPT pipe threads are tapered at 3/4 inch per foot of diameter, which is what makes the joint seal as it tightens.

Pipe is specified by nominal pipe size and schedule; for a given NPS the outside diameter is fixed and a higher schedule means a thicker wall and a smaller bore.

Reaming the burr from the inside of a freshly cut pipe end is required, because the burr restricts flow and starts turbulence and erosion.

Thread sealant or tape is applied to the male thread only, in the direction of the thread, and never on the first one or two threads where it can shed into the system.

Module 32204 contributes to both the Fundamentals domain and the 16-item Valves and Seals domain, so piping practice is worth studying twice over.

Last updated: September 2026

A module that pays twice

Module 32204, Introduction to Ferrous Metal Piping Practices , is referenced by two content domains: it appears in the 14-item Fundamentals domain and again in the 16-item Valves and Seals domain. Very few modules carry that double weighting, which makes ferrous pipe practice one of the highest-value study targets on the whole assessment.

Identifying pipe: NPS, schedule, and the fixed outside diameter

Pipe is specified by nominal pipe size (NPS) and schedule , not by the dimension you can measure with a tape.

For any given NPS, the outside diameter is fixed . A 2-inch NPS pipe has an outside diameter of 2.375 inches whether it is Schedule 40 or Schedule 80.

Schedule sets the wall thickness. A higher schedule number means a thicker wall and therefore a smaller inside diameter and higher pressure rating.

This is why the same fittings, threading dies, and flanges fit across schedules of the same NPS: the outside is identical.

  • NPS Outside diameter Sch 40 wall Sch 80 wall
  • 1/2 in 0.840 in 0.109 in 0.147 in
  • 1 in 1.315 in 0.133 in 0.179 in
  • 2 in 2.375 in 0.154 in 0.218 in
  • 4 in 4.500 in 0.237 in 0.337 in
  • 6 in 6.625 in 0.280 in 0.432 in

Tube, by contrast, is specified by actual outside diameter and wall thickness or gauge. Confusing pipe sizing with tube sizing is a classic distractor.

Fittings and what each one does

  • Fitting Purpose
  • 90° and 45° elbow Change direction; long-radius elbows reduce turbulence and erosion
  • Tee (straight or reducing) Branch a line
  • Coupling Join two lengths of the same size

Reducer (concentric or eccentric) Change size; eccentric keeps one side flat so vapor cannot pocket on a pump suction

  • Union Allow disassembly of a threaded line without cutting
  • Nipple Short length of pipe threaded both ends; a close nipple is threaded end to end
  • Cap and plug Close a line end or a fitting port
  • Bushing Reduce a female port; restricts flow and is avoided on high-pressure service
  • Flange Bolted connection allowing removal of valves and equipment

An eccentric reducer installed flat side up on a horizontal pump suction prevents an air pocket from forming ahead of the impeller. That single detail links this module to the pump troubleshooting module in Domain 8.

Cutting, reaming, and preparing ends

Measurement methods matter. End-to-end measurement includes the fittings; end-to-center and center-to-center are used with elbows and tees, and both require subtracting the fitting take-out and adding back the thread engagement to get the correct pipe length.

Cutting tools:

Wheel-type pipe cutter — fast and square, but it rolls a heavy internal burr and slightly reduces the bore at the cut.

Hacksaw or portable band saw — leaves less burr; the cut must be checked for square.

Abrasive chop saw — fast on carbon steel; generates heat and sparks, so it is hot work.

Every cut end must be reamed to remove the internal burr. An unreamed burr restricts flow, creates turbulence that erodes the pipe wall downstream, and can shed metal into pumps and valve seats.

Threading ferrous pipe

Standard ferrous pipe threads are NPT — National Pipe Taper . The thread is cut on a taper of 3/4 inch per foot of diameter (a 1-in-16 taper). The taper is the sealing mechanism: as the joint is made up, the flanks of the male and female threads are wedged together.

Threading practice:

Secure the pipe in a chain or yoke vise close to the work.

Select the correct die head and size; ensure the die is sharp and the guides are set.

Apply cutting oil generously and continuously during threading. Threading dry overheats and tears the thread crests, producing a leaking joint.

Cut until the pipe end is flush with or barely past the outer face of the die.

Back the die off, remove chips with a brush, and inspect for torn or thin threads.

Thread engagement is measured by hand-tight and wrench-tight turns. A commonly taught guide is roughly three turns hand-tight plus three turns wrench-tight on small sizes; the assessment is more interested in the principle that over-tightening splits fittings and under-tightening leaks.

Sealants and make-up

Apply pipe joint compound or PTFE tape to the male thread only . Compound inside a female port will be pushed into the system.

Wrap tape in the direction the fitting will turn so tightening does not unwrap it.

Leave the first one or two threads bare so shredded tape cannot enter and lodge in a valve seat or a control orifice.

Use a union rather than breaking a run when a valve or instrument will need removal.

Back-hold with a second wrench on the fitting when tightening, so the torque is not transmitted into the connected equipment.

Flanged and welded joints

Flanged joints are made by matching the flange class (150, 300, 600 and so on) and facing (raised face, flat face, ring-type joint), inserting the correct gasket, and tightening the bolts in a star or crisscross pattern in graduated torque passes so the gasket is compressed evenly.

Welded ferrous joints for a mechanic's purposes come in two families: butt weld , where the pipe ends are beveled and joined end to end for the smoothest bore, and socket weld , where the pipe slides into a recessed fitting and is fillet welded. Socket welds require a gap — commonly about 1/16 inch — between the pipe end and the bottom of the socket before welding, so thermal expansion does not crack the weld root.