Study guide
2.4 Oxyfuel Cutting: Equipment, Safe Setup, and Cutting Practice
NCCER Industrial Maintenance Mechanic Exam
Track your progress as you read
Finished sections get a check mark.
1 The NCCER Industrial Maintenance Mechanic Assessment
1.1 The IMM Journey-Level Credential and Assessment Specification 1.2 The Nine Content Domains: Item Counts and a Study Plan
2 Industrial Maintenance Mechanic Fundamentals
2.1 Safety Programs, PPE, and Hazard Communication 2.2 Hazardous Energy Control: Lockout/Tagout and Confined Space Entry 2.3 Tools of the Trade: Hand and Power Tools 2.4 Oxyfuel Cutting: Equipment, Safe Setup, and Cutting Practice 2.5 Ferrous Metal Piping Practices: Cutting, Threading, and Joining
3 Rigging and Mobile Equipment
3.1 Slings, Rigging Hardware, and Inspection Criteria 3.2 Load Weight, Center of Gravity, Sling Angle, and Hand Signals 3.3 Mobile and Support Equipment: Forklifts, Aerial Lifts, and Mobile Cranes
4 Craft Mathematics, Layout, and Precision Measurement
4.1 Craft-Related Mathematics: Fractions, Units, Area, and Volume 4.2 Advanced Trade Math: Right Triangles, Trigonometry, and Pipe Offsets 4.3 Basic Layout: Squaring, Leveling, and Transferring Elevations 4.4 Precision Measuring Tools: Micrometers, Verniers, and Dial Indicators 4.5 Gauges, Tolerances and Fits, and Torque Measurement
5 Construction Drawings and Blueprint Reading
5.1 Reading Construction Drawings: Views, Lines, Scales, and the Title Block 5.2 Orthographic, Isometric, Arrangement, and Foundation Drawings 5.3 Advanced Blueprint Reading: P&IDs, Instrument Tags, and Welding Symbols
6 Valves, Packing, and Mechanical Seals
6.1 Valve Types and Service Selection 6.2 Valve Construction, Markings, Pressure Classes, and Actuators 6.3 Removing and Installing Valves: Flange Bolting and Torque Sequence 6.4 Valve Maintenance: Packing, Stuffing Boxes, Gaskets, and O-Rings 6.5 Hydrostatic and Pneumatic Testing of Piping and Equipment 6.6 Mechanical Seals: Components, Types, and Installation
7 Bearings, Lubrication, and Couplings
7.1 Bearing Types, Designations, and Selection 7.2 Bearing Lubrication, Handling, and Failure Analysis 7.3 Removing and Installing Bearings: Fits, Heating, and Mounting 7.4 Couplings: Types, Selection, and Installation
8 Pumps, Baseplates, and Mechanical Drives
8.1 Pumps and Drivers: Centrifugal and Positive Displacement 8.2 Setting Baseplates and Soleplates: Leveling, Anchoring, and Grouting 8.3 Prealignment: Soft Foot, Runout, Pipe Strain, and Shims 8.4 Installing Belt and Chain Drives
9 Shaft Alignment: Conventional, Reverse, and Laser
9.1 Conventional Rim-and-Face Dial Indicator Alignment 9.2 Reverse Dial Indicator Alignment 9.3 Laser Shaft Alignment Systems
10 Maintenance Troubleshooting: Method, Pumps, and Gearboxes
10.1 Systematic Troubleshooting and Root Cause Analysis 10.2 Troubleshooting and Repairing Pumps 10.3 Troubleshooting and Repairing Gearboxes
11 Steam Systems, Boilers, and Process Vessels
11.1 Low-Pressure Steam Systems, Traps, and Condensate Return 11.2 High-Pressure Steam Generation and Boiler Auxiliaries 11.3 Distillation Towers, Vessels, and Internals
12 Compressors and Pneumatic Systems
12.1 Air Compressor Types, Operation, and Maintenance 12.2 Compressed Air Treatment, Storage, and Distribution 12.3 FRL Units, Pneumatic Valves, Actuators, and Speed Control
2.4 Oxyfuel Cutting: Equipment, Safe Setup, and Cutting Practice
Key Takeaways Explain This Topic AI
OSHA 29 CFR 1910.253 prohibits opening an acetylene cylinder valve more than one and one-half turns, and preferably no more than three-fourths of a turn.
Acetylene must never be used at a working pressure above 15 psig because it becomes chemically unstable.
Stored oxygen cylinders must be separated from fuel gas cylinders by 20 feet or by a noncombustible barrier at least 5 feet high with a fire-resistance rating of at least one-half hour.
A neutral flame has a clearly defined inner cone with no acetylene feather and is the flame used for most cutting and welding.
Oxyfuel cutting works by preheating steel to its kindling temperature and then oxidizing it with a stream of pure oxygen, which is why it does not cut aluminum or stainless steel effectively.
Last updated: September 2026
How oxyfuel cutting actually works
Oxyfuel cutting is a chemical oxidation process, not a melting process. The preheat flames raise the steel to its kindling temperature — roughly 1,600°F, a bright cherry red — and then the cutting oxygen lever releases a high-purity oxygen jet that burns the iron into iron oxide. The oxygen stream blows the molten oxide out of the joint, forming the kerf .
That mechanism explains a fact the assessment likes to test: oxyfuel cutting works on carbon and low-alloy steels but performs poorly on aluminum, stainless steel, cast iron, and copper alloys , because their oxides melt at a higher temperature than the base metal and form a refractory skin that stops the reaction.
Cylinders, regulators, and hose
- Component Key facts
- Oxygen cylinder Right-hand threads; green in common US practice; full cylinder about 2,200 psi at 70°F
Acetylene cylinder Left-hand threads with a notched nut; packed with a porous filler saturated in acetone; must be stored and used valve end up
Regulators Two-stage on the cylinder, showing cylinder pressure and working pressure; always back out the adjusting screw before opening the cylinder valve
Hose Green for oxygen with right-hand fittings; red for fuel gas with left-hand notched fittings
Check valves and flashback arrestors Reverse-flow check valves prevent gas mixing in the hoses; flashback arrestors stop a flame front from travelling back to the cylinder
Handling and storage rules that appear verbatim on assessments:
Transport cylinders with the valve protection cap in place, secured upright, using a cart or cradle. Never lift a cylinder by the cap and never use a magnet or a sling around the body.
Never allow oil or grease to contact oxygen fittings. Oxygen under pressure ignites hydrocarbons spontaneously.
Store oxygen cylinders at least 20 feet from fuel gas cylinders and combustible material, or separate them with a noncombustible barrier at least 5 feet high with a fire-resistance rating of at least one-half hour .
If an acetylene cylinder is laid on its side, stand it upright for at least the time your employer's procedure requires — commonly a minimum of one hour and often longer — before use so the acetone settles.
Never open an acetylene cylinder valve more than one and one-half turns, and preferably no more than three-fourths of a turn , so it can be closed quickly in an emergency. Leave the wrench on the valve stem if the cylinder uses one.
Never exceed 15 psig working pressure with acetylene. Above that, acetylene can dissociate explosively even without air.
Lighting, flame adjustment, and shutdown
The lighting sequence is: open the fuel valve slightly, ignite with a friction striker (never a lighter or a match held in the hand), then add oxygen until the flame is correct. Shutdown reverses the emphasis: close the fuel valve first on the torch, then the oxygen, then close cylinder valves, bleed both lines, and back out the regulator adjusting screws.
Three flames, all testable:
Flame Appearance Chemistry Use
Carburizing (reducing) Bright inner cone with a feathery acetylene plume around it Excess fuel Adds carbon to the puddle; used for hard-facing, not general cutting
Neutral Sharply defined inner cone, feather just disappeared Balanced 1:1 Standard preheat for cutting and general welding
Oxidizing Short, sharp, necked-in inner cone with a hissing sound Excess oxygen Burns carbon out; causes scale and porosity in steel
Adjust by first setting a carburizing flame and then adding oxygen until the acetylene feather just disappears . That is neutral.
Cutting technique and quality indicators
Preheat the edge to a bright cherry red, then depress the cutting oxygen lever smoothly and begin travel. Quality is read off the cut face:
Drag lines should be nearly vertical and evenly spaced. Curved, backward-trailing drag lines mean travel speed is too fast .
Excessive slag adhering to the bottom edge usually indicates travel too slow, preheat too high, or a tip too large.
A rounded, melted top edge indicates preheat too high or the torch held too close.
Loss of cut partway through means travel too fast, oxygen pressure too low, or a clogged tip.
Tip size is selected from the manufacturer's chart based on material thickness , and each tip has published oxygen and fuel pressures. A tip cleaner is used to restore the orifice; a drill bit or welding rod enlarges and bells the orifice and ruins cut quality.
Backfire and flashback
A backfire is a momentary loud pop at which the flame goes out or immediately reignites. Causes include touching the tip to the work, a tip that is overheated or dirty, or incorrect pressures.
A flashback is a flame that travels back inside the torch, hose, or regulator, producing a shrill squeal or hiss. It is an emergency: close the torch oxygen valve first, then the fuel valve , then close both cylinder valves and take the equipment out of service until it is inspected.
Flashback arrestors and reverse-flow check valves exist precisely because the consequence of a flashback reaching an acetylene cylinder is catastrophic.
Hot work controls
Cutting inside a plant is hot work. A hot work permit, a fire watch maintained during the work and for at least 30 minutes afterward under common permit practice, removal or protection of combustibles within 35 feet , and closing of floor and wall openings are the controls a mechanic is expected to name.