Study guide

4.5 Gauges, Tolerances and Fits, and Torque Measurement

NCCER Industrial Maintenance Mechanic Exam

Track your progress as you read

Finished sections get a check mark.

1 The NCCER Industrial Maintenance Mechanic Assessment

1.1 The IMM Journey-Level Credential and Assessment Specification 1.2 The Nine Content Domains: Item Counts and a Study Plan

2 Industrial Maintenance Mechanic Fundamentals

2.1 Safety Programs, PPE, and Hazard Communication 2.2 Hazardous Energy Control: Lockout/Tagout and Confined Space Entry 2.3 Tools of the Trade: Hand and Power Tools 2.4 Oxyfuel Cutting: Equipment, Safe Setup, and Cutting Practice 2.5 Ferrous Metal Piping Practices: Cutting, Threading, and Joining

3 Rigging and Mobile Equipment

3.1 Slings, Rigging Hardware, and Inspection Criteria 3.2 Load Weight, Center of Gravity, Sling Angle, and Hand Signals 3.3 Mobile and Support Equipment: Forklifts, Aerial Lifts, and Mobile Cranes

4 Craft Mathematics, Layout, and Precision Measurement

4.1 Craft-Related Mathematics: Fractions, Units, Area, and Volume 4.2 Advanced Trade Math: Right Triangles, Trigonometry, and Pipe Offsets 4.3 Basic Layout: Squaring, Leveling, and Transferring Elevations 4.4 Precision Measuring Tools: Micrometers, Verniers, and Dial Indicators 4.5 Gauges, Tolerances and Fits, and Torque Measurement

5 Construction Drawings and Blueprint Reading

5.1 Reading Construction Drawings: Views, Lines, Scales, and the Title Block 5.2 Orthographic, Isometric, Arrangement, and Foundation Drawings 5.3 Advanced Blueprint Reading: P&IDs, Instrument Tags, and Welding Symbols

6 Valves, Packing, and Mechanical Seals

6.1 Valve Types and Service Selection 6.2 Valve Construction, Markings, Pressure Classes, and Actuators 6.3 Removing and Installing Valves: Flange Bolting and Torque Sequence 6.4 Valve Maintenance: Packing, Stuffing Boxes, Gaskets, and O-Rings 6.5 Hydrostatic and Pneumatic Testing of Piping and Equipment 6.6 Mechanical Seals: Components, Types, and Installation

7 Bearings, Lubrication, and Couplings

7.1 Bearing Types, Designations, and Selection 7.2 Bearing Lubrication, Handling, and Failure Analysis 7.3 Removing and Installing Bearings: Fits, Heating, and Mounting 7.4 Couplings: Types, Selection, and Installation

8 Pumps, Baseplates, and Mechanical Drives

8.1 Pumps and Drivers: Centrifugal and Positive Displacement 8.2 Setting Baseplates and Soleplates: Leveling, Anchoring, and Grouting 8.3 Prealignment: Soft Foot, Runout, Pipe Strain, and Shims 8.4 Installing Belt and Chain Drives

9 Shaft Alignment: Conventional, Reverse, and Laser

9.1 Conventional Rim-and-Face Dial Indicator Alignment 9.2 Reverse Dial Indicator Alignment 9.3 Laser Shaft Alignment Systems

10 Maintenance Troubleshooting: Method, Pumps, and Gearboxes

10.1 Systematic Troubleshooting and Root Cause Analysis 10.2 Troubleshooting and Repairing Pumps 10.3 Troubleshooting and Repairing Gearboxes

11 Steam Systems, Boilers, and Process Vessels

11.1 Low-Pressure Steam Systems, Traps, and Condensate Return 11.2 High-Pressure Steam Generation and Boiler Auxiliaries 11.3 Distillation Towers, Vessels, and Internals

12 Compressors and Pneumatic Systems

12.1 Air Compressor Types, Operation, and Maintenance 12.2 Compressed Air Treatment, Storage, and Distribution 12.3 FRL Units, Pneumatic Valves, Actuators, and Speed Control

4.5 Gauges, Tolerances and Fits, and Torque Measurement

Key Takeaways Explain This Topic AI

Tolerance is the total permissible variation in a dimension, equal to the difference between the upper and lower limits.

A clearance fit always leaves space between shaft and housing, an interference fit always requires force or heat, and a transition fit may be either.

Bearings are normally mounted with an interference fit on the rotating ring and a clearance fit on the stationary ring.

Feeler gauges measure clearance and can be stacked, but the stack should use the fewest possible leaves to limit cumulative error.

When an extension is added to a torque wrench along its axis, the wrench must be set below the target torque, because the effective lever arm has increased.

Last updated: September 2026

Gauges that transfer or compare rather than read

Not every precision instrument has a scale. Several of the most useful ones transfer a dimension to a micrometer or compare against a known standard.

Gauge What it does Typical maintenance use

Feeler (thickness) gauge Direct-reading leaves of known thickness Coupling gap, valve clearance, soft foot, bearing internal clearance

Telescoping gauge Expands to a bore, then is locked and measured with a micrometer Housing bores, bushing bores

  • Small-hole (ball) gauge Expands a split ball into a small bore Small bores below telescoping gauge range
  • Taper gauge Wedge marked with width Gap width in a slot or crack
  • Thread pitch gauge Leaves matching standard pitches Identifying an unknown fastener or pipe thread
  • Radius gauge Fillet and corner radii Verifying a shaft fillet will clear a bearing corner
  • Plug and ring gauges Go / no-go comparison Production inspection of bores and shafts
  • Straightedge Reference plane Checking shaft and sheave alignment, flatness of a mounting surface

Two disciplines govern the transfer gauges: do not force them , because forcing springs the gauge and reads oversize, and measure the gauge immediately with a micrometer using normal ratchet pressure.

When stacking feeler leaves, use the fewest leaves that make the required thickness. Every additional leaf adds its own thickness tolerance and a little surface film, so a four-leaf stack is less trustworthy than a single leaf of the same nominal size.

Tolerance, allowance, and fits

  • Term Definition
  • Nominal size The designation used to identify the part, such as a 2-inch shaft
  • Basic size The theoretical exact size from which limits are derived
  • Limits The maximum and minimum permissible sizes
  • Tolerance The total permissible variation: upper limit minus lower limit
  • Allowance The intentional difference between mating parts at their tightest condition
  • Bilateral tolerance Variation permitted in both directions, such as 2.000 ± 0.002
  • Unilateral tolerance Variation permitted in one direction only, such as 2.000 +0.000 / −0.003

A shaft specified as 2.0000 / 1.9985 inch has a tolerance of 0.0015 inch. If the mating bore is 1.9995 / 1.9990, the parts will always interfere at some combinations and clear at others — a transition fit .

The three fit classes:

Clearance fit — the shaft is always smaller than the hole. Assembly is by hand. Used for sliding parts and for the stationary ring of a bearing.

Transition fit — depending on where each part falls within its tolerance, the fit may be slightly loose or slightly tight. Used for locating parts that must be accurate but removable.

Interference (press) fit — the shaft is always larger than the hole. Assembly requires force, cooling the shaft, or heating the housing. Used for the rotating ring of a bearing and for coupling hubs.

The governing rule for bearings, which returns in Chapter 7: the ring that rotates relative to the load gets the interference fit; the ring that stands still gets the clearance fit. On a normal pump or motor, that means an interference fit on the shaft and a clearance fit in the housing.

  • Torque measurement
  • Torque is force applied at a distance: T = F × d T = F \times d T = F × d

Tightening a fastener to a specified torque is a proxy for producing a specified clamping force . That proxy is imperfect: roughly 85 to 90 percent of applied torque is consumed by friction in the threads and under the head, so lubrication state matters enormously. A dry torque specification applied to a lubricated fastener over-tightens it, often past yield.

  • Wrench type Characteristics
  • Beam Simple, inherently stable calibration, must be read while pulling, no overtorque protection
  • Click Signals the setting with an audible click; store at the lowest setting
  • Dial Continuous reading, good for measuring breakaway torque on an existing fastener
  • Digital / electronic Readout with peak-hold and angle capability
  • Torque multiplier Gear reduction for large fasteners; output equals input times the stated ratio

Rules that produce assessment items:

Never use a torque wrench as a breaker bar and never add a cheater pipe to the handle.

Pull smoothly to the setting and stop. Re-clicking a fastener adds torque.

Follow the specified pattern — star or crisscross on flanges and bearing housings — in graduated passes, typically 30 percent, 60 percent, and 100 percent of final torque.

If a crowfoot or extension is added along the axis of the handle , the effective lever arm grows, so the wrench must be set lower than the target torque : T setting = T target × L L + E T_{\text{setting}} = T_{\text{target}} \times \frac{L}{L + E} T setting ​ = T target ​ × L + E L ​

where L is the wrench length from the drive to the handle grip and E is the extension length. Mounting the crowfoot at 90 degrees to the handle does not change the effective lever arm, so no correction is needed.

Worked example. Target torque is 100 ft-lb. The wrench is 18 inches and a 3-inch crowfoot is added in line. Set the wrench to 100 times 18, divided by 21, which is 86 ft-lb .