Study guide

6.2 Valve Construction, Markings, Pressure Classes, and Actuators

NCCER Industrial Maintenance Mechanic Exam

Track your progress as you read

Finished sections get a check mark.

1 The NCCER Industrial Maintenance Mechanic Assessment

1.1 The IMM Journey-Level Credential and Assessment Specification 1.2 The Nine Content Domains: Item Counts and a Study Plan

2 Industrial Maintenance Mechanic Fundamentals

2.1 Safety Programs, PPE, and Hazard Communication 2.2 Hazardous Energy Control: Lockout/Tagout and Confined Space Entry 2.3 Tools of the Trade: Hand and Power Tools 2.4 Oxyfuel Cutting: Equipment, Safe Setup, and Cutting Practice 2.5 Ferrous Metal Piping Practices: Cutting, Threading, and Joining

3 Rigging and Mobile Equipment

3.1 Slings, Rigging Hardware, and Inspection Criteria 3.2 Load Weight, Center of Gravity, Sling Angle, and Hand Signals 3.3 Mobile and Support Equipment: Forklifts, Aerial Lifts, and Mobile Cranes

4 Craft Mathematics, Layout, and Precision Measurement

4.1 Craft-Related Mathematics: Fractions, Units, Area, and Volume 4.2 Advanced Trade Math: Right Triangles, Trigonometry, and Pipe Offsets 4.3 Basic Layout: Squaring, Leveling, and Transferring Elevations 4.4 Precision Measuring Tools: Micrometers, Verniers, and Dial Indicators 4.5 Gauges, Tolerances and Fits, and Torque Measurement

5 Construction Drawings and Blueprint Reading

5.1 Reading Construction Drawings: Views, Lines, Scales, and the Title Block 5.2 Orthographic, Isometric, Arrangement, and Foundation Drawings 5.3 Advanced Blueprint Reading: P&IDs, Instrument Tags, and Welding Symbols

6 Valves, Packing, and Mechanical Seals

6.1 Valve Types and Service Selection 6.2 Valve Construction, Markings, Pressure Classes, and Actuators 6.3 Removing and Installing Valves: Flange Bolting and Torque Sequence 6.4 Valve Maintenance: Packing, Stuffing Boxes, Gaskets, and O-Rings 6.5 Hydrostatic and Pneumatic Testing of Piping and Equipment 6.6 Mechanical Seals: Components, Types, and Installation

7 Bearings, Lubrication, and Couplings

7.1 Bearing Types, Designations, and Selection 7.2 Bearing Lubrication, Handling, and Failure Analysis 7.3 Removing and Installing Bearings: Fits, Heating, and Mounting 7.4 Couplings: Types, Selection, and Installation

8 Pumps, Baseplates, and Mechanical Drives

8.1 Pumps and Drivers: Centrifugal and Positive Displacement 8.2 Setting Baseplates and Soleplates: Leveling, Anchoring, and Grouting 8.3 Prealignment: Soft Foot, Runout, Pipe Strain, and Shims 8.4 Installing Belt and Chain Drives

9 Shaft Alignment: Conventional, Reverse, and Laser

9.1 Conventional Rim-and-Face Dial Indicator Alignment 9.2 Reverse Dial Indicator Alignment 9.3 Laser Shaft Alignment Systems

10 Maintenance Troubleshooting: Method, Pumps, and Gearboxes

10.1 Systematic Troubleshooting and Root Cause Analysis 10.2 Troubleshooting and Repairing Pumps 10.3 Troubleshooting and Repairing Gearboxes

11 Steam Systems, Boilers, and Process Vessels

11.1 Low-Pressure Steam Systems, Traps, and Condensate Return 11.2 High-Pressure Steam Generation and Boiler Auxiliaries 11.3 Distillation Towers, Vessels, and Internals

12 Compressors and Pneumatic Systems

12.1 Air Compressor Types, Operation, and Maintenance 12.2 Compressed Air Treatment, Storage, and Distribution 12.3 FRL Units, Pneumatic Valves, Actuators, and Speed Control

6.2 Valve Construction, Markings, Pressure Classes, and Actuators

Key Takeaways Explain This Topic AI

ASME pressure classes for flanged valves run 150, 300, 600, 900, 1500, and 2500, and the class is a rating designation rather than a working pressure in psi.

A valve's allowable working pressure falls as temperature rises, which is why pressure-temperature rating tables exist for each class and material.

MSS SP-25 requires valve markings including the manufacturer, size, pressure class, and body material designation such as WCB.

The bonnet closes the body and carries the stem and packing; the yoke on an OS&Y valve carries the stem nut outside the packing.

Fail action must be known before isolating an actuated valve, because fail-closed and fail-open valves move in opposite directions when air is lost.

Last updated: September 2026

Parts of a valve

  • Part Function
  • Body The pressure-containing shell and the connection to the pipe
  • Bonnet Closes the body opening; carries the stem, packing, and gland
  • Yoke On an OS&Y valve, supports the stem nut outside the packing
  • Trim The internal wear parts: disc, seat, stem, and guides
  • Disc / plug / ball / gate The closure element that stops or throttles flow
  • Seat The surface the closure element seals against
  • Stem Transmits motion from the operator to the closure element
  • Packing Seals around the moving stem to prevent leakage to atmosphere
  • Gland and gland follower Compress the packing into the stuffing box
  • Handwheel, lever, or actuator Applies the operating force

Trim material is specified separately from the body, because the trim sees the velocity and erosion. A carbon steel body with stainless trim is the most common industrial combination.

Body materials and markings

MSS SP-25 standardizes valve markings so a mechanic can identify a valve from the casting. Expect to find, cast or stamped on the body or a nameplate: the manufacturer's name or trademark , the nominal size , the pressure class , the body material designation , and often the melt or heat number and the flow direction arrow .

  • Marking Material
  • WCB Cast carbon steel, the industrial workhorse
  • WC6 / WC9 Chrome-moly alloy steel for elevated temperature
  • CF8 / CF8M Cast stainless, equivalent to 304 and 316
  • A126 Class B Cast iron, low-pressure water and non-critical service
  • A395 / ductile iron Higher-strength iron
  • Bronze / brass Small utility valves, potable water

Cast iron is the material to be cautious with: it is brittle, has no meaningful ductility, and cracks when a raised-face flange is bolted directly against it . The flat-face rule in the next section exists because of this.

Pressure class and the temperature derate

Flanged valves and flanges are rated in ASME classes : 150, 300, 600, 900, 1500, and 2500.

The trap: a class number is a designation , not a working pressure. A Class 150 carbon steel valve is not limited to 150 psi. At ambient temperature a Class 150 WCB valve is rated for roughly 285 psig, but its allowable pressure falls as temperature rises , dropping to a fraction of that at high-temperature steam conditions. Each combination of class and material has its own pressure-temperature table.

  • Class Approximate WCB rating at ambient Approximate rating at 600°F
  • 150 285 psig 140 psig
  • 300 740 psig 550 psig
  • 600 1,480 psig 1,095 psig

Treat those figures as illustrative of the trend — always read the actual rating table for the specific material. The examinable idea is that higher temperature means lower allowable pressure for the same class .

End connections

  • Connection Where used
  • Threaded (NPT) Small sizes, utility service, typically 2 inch and below
  • Socket weld Small high-pressure lines; pipe bottoms into a recess with a gap
  • Butt weld Large high-pressure and high-temperature lines; smoothest bore
  • Flanged Anywhere the valve must be removable; matched by class and facing
  • Wafer / lug Butterfly and dual-plate check valves between flanges
  • Grooved Fire protection and utility piping with mechanical couplings
  • Actuators
  • Actuator Characteristics
  • Handwheel Direct manual; a gear operator multiplies torque on large valves
  • Lever Quarter-turn manual; position is visible from the handle
  • Chainwheel Extends manual operation to valves out of reach
  • Diaphragm Spring-opposed air actuator for control valves; inherently fail-safe
  • Piston / cylinder Higher thrust than a diaphragm; air or hydraulic
  • Electric motor operator Gear train and motor; holds position on power loss
  • Solenoid Direct electrical operation on small valves

Fail action is the safety-critical property. A spring-opposed diaphragm actuator drives the valve to a defined position when air is lost: fail closed (FC) , fail open (FO) , or fail last position on some piston designs. Before any isolation or instrument air outage, the crew confirms fail action from the P&ID so it knows what the process will do the moment air is cut.

A gear operator is not a suggestion to apply more force. Cheater bars and impact wrenches on a valve handwheel deform stems, strip gearing, and crush seats. If a valve will not move under normal effort, the answer is a valve problem, not a torque problem.

Body construction: cast, forged, and fabricated

Construction Where it is used What to watch for

Cast The industrial default, and the only practical way to produce a complex body shape in larger sizes Casting porosity and shrinkage defects; repairs to a pressure-containing casting are a code matter, not a welding decision

Forged Small sizes in high-pressure service, usually 2 inch and below with threaded or socket-weld ends Denser grain structure and no porosity, but limited to shapes a die can produce

Fabricated (plate) Very large valves where a casting would be impractical Body is welded from plate, so weld integrity is the pressure boundary

Bonnet-to-body joint construction

The bonnet joint is the largest static seal on a valve and the one a mechanic opens most often. How it is built determines how it is opened.

Bonnet joint Typical service Practical consequence

Screwed / union bonnet Small bronze and low-pressure valves Fast to open, but repeated cycling wears the thread; no gasket load control

Bolted bonnet The industrial standard across Class 150 through Class 600 Gasket load is set by bolt torque, so it is re-torqued in a crisscross pattern in passes

Welded bonnet High-pressure lines where nothing is expected to be opened Cannot be serviced in place; the valve is a replace-not-repair item

Pressure-seal bonnet Class 900 and above, power-plant steam service Internal pressure drives a seal ring tighter, so the joint seals better as pressure rises, but disassembly follows a specific manufacturer sequence

The pressure-seal design carries a trap worth remembering: because the seal is energized by line pressure, a pressure-seal joint may leak at low pressure and seal at full pressure . Diagnosing a weep during a slow warm-up as a failed joint has led crews to disassemble a sound valve.

Body split patterns

How the body comes apart decides whether the valve can be serviced without cutting it out of the line.

End-entry or three-piece ball valves unbolt into a centre section and two end caps, so the ball and seats come out with the body ends still welded to the pipe. This is the maintenance-friendly pattern.

Split-body (side-entry) valves separate on a vertical flange through the body, giving access to trim from the side.

Top-entry valves are serviced by removing the bonnet only, with the body left welded in the line — the reason top-entry trunnion ball valves are chosen for buried and hard-to-remove service.

One-piece bodies cannot be opened at all and are replaced on failure.

Before planning any valve repair, identify the split pattern from the body casting and the manufacturer's drawing. A crew that plans an in-line trim change on a one-piece body has planned a valve replacement without knowing it.