Study guide

8.2 Setting Baseplates and Soleplates: Leveling, Anchoring, and Grouting

NCCER Industrial Maintenance Mechanic Exam

Track your progress as you read

Finished sections get a check mark.

1 The NCCER Industrial Maintenance Mechanic Assessment

1.1 The IMM Journey-Level Credential and Assessment Specification 1.2 The Nine Content Domains: Item Counts and a Study Plan

2 Industrial Maintenance Mechanic Fundamentals

2.1 Safety Programs, PPE, and Hazard Communication 2.2 Hazardous Energy Control: Lockout/Tagout and Confined Space Entry 2.3 Tools of the Trade: Hand and Power Tools 2.4 Oxyfuel Cutting: Equipment, Safe Setup, and Cutting Practice 2.5 Ferrous Metal Piping Practices: Cutting, Threading, and Joining

3 Rigging and Mobile Equipment

3.1 Slings, Rigging Hardware, and Inspection Criteria 3.2 Load Weight, Center of Gravity, Sling Angle, and Hand Signals 3.3 Mobile and Support Equipment: Forklifts, Aerial Lifts, and Mobile Cranes

4 Craft Mathematics, Layout, and Precision Measurement

4.1 Craft-Related Mathematics: Fractions, Units, Area, and Volume 4.2 Advanced Trade Math: Right Triangles, Trigonometry, and Pipe Offsets 4.3 Basic Layout: Squaring, Leveling, and Transferring Elevations 4.4 Precision Measuring Tools: Micrometers, Verniers, and Dial Indicators 4.5 Gauges, Tolerances and Fits, and Torque Measurement

5 Construction Drawings and Blueprint Reading

5.1 Reading Construction Drawings: Views, Lines, Scales, and the Title Block 5.2 Orthographic, Isometric, Arrangement, and Foundation Drawings 5.3 Advanced Blueprint Reading: P&IDs, Instrument Tags, and Welding Symbols

6 Valves, Packing, and Mechanical Seals

6.1 Valve Types and Service Selection 6.2 Valve Construction, Markings, Pressure Classes, and Actuators 6.3 Removing and Installing Valves: Flange Bolting and Torque Sequence 6.4 Valve Maintenance: Packing, Stuffing Boxes, Gaskets, and O-Rings 6.5 Hydrostatic and Pneumatic Testing of Piping and Equipment 6.6 Mechanical Seals: Components, Types, and Installation

7 Bearings, Lubrication, and Couplings

7.1 Bearing Types, Designations, and Selection 7.2 Bearing Lubrication, Handling, and Failure Analysis 7.3 Removing and Installing Bearings: Fits, Heating, and Mounting 7.4 Couplings: Types, Selection, and Installation

8 Pumps, Baseplates, and Mechanical Drives

8.1 Pumps and Drivers: Centrifugal and Positive Displacement 8.2 Setting Baseplates and Soleplates: Leveling, Anchoring, and Grouting 8.3 Prealignment: Soft Foot, Runout, Pipe Strain, and Shims 8.4 Installing Belt and Chain Drives

9 Shaft Alignment: Conventional, Reverse, and Laser

9.1 Conventional Rim-and-Face Dial Indicator Alignment 9.2 Reverse Dial Indicator Alignment 9.3 Laser Shaft Alignment Systems

10 Maintenance Troubleshooting: Method, Pumps, and Gearboxes

10.1 Systematic Troubleshooting and Root Cause Analysis 10.2 Troubleshooting and Repairing Pumps 10.3 Troubleshooting and Repairing Gearboxes

11 Steam Systems, Boilers, and Process Vessels

11.1 Low-Pressure Steam Systems, Traps, and Condensate Return 11.2 High-Pressure Steam Generation and Boiler Auxiliaries 11.3 Distillation Towers, Vessels, and Internals

12 Compressors and Pneumatic Systems

12.1 Air Compressor Types, Operation, and Maintenance 12.2 Compressed Air Treatment, Storage, and Distribution 12.3 FRL Units, Pneumatic Valves, Actuators, and Speed Control

8.2 Setting Baseplates and Soleplates: Leveling, Anchoring, and Grouting

Key Takeaways Explain This Topic AI

Grout transfers machine load into the foundation, damps vibration, and preserves the alignment achieved at installation.

Machined mounting surfaces on a baseplate are normally leveled and made coplanar within about 0.002 inch per foot, verified with a precision level.

Epoxy grout has higher compressive strength and better chemical resistance than cementitious grout and does not shrink away from the baseplate.

Jackscrews used to level a baseplate must be backed off or removed after the grout cures, so the load transfers to the grout rather than to the screws.

Anchor bolts in sleeves allow lateral adjustment, and the sleeve must be packed before grouting so grout does not lock the bolt.

Last updated: September 2026

Why grout exists

A rotating machine bolted to a baseplate that is bolted to concrete has to become one structure. The grout is what makes that happen. It does three jobs:

Transfers the machine's static and dynamic load into the foundation over the full area of the baseplate, rather than through a handful of shims.

Damps vibration by adding mass and stiffness under the machine.

Holds the alignment achieved at installation, by preventing the baseplate from flexing or shifting.

A poorly grouted baseplate is the root cause behind an enormous number of "chronic misalignment" machines. No amount of alignment work fixes a base that moves.

Preparing the foundation

Chip the concrete to remove the weak, laitance-rich top layer until sound aggregate is exposed. Typically 1 to 2 inches is removed. Chipping is done with hand chisels or light chipping hammers; heavy demolition hammers fracture the concrete below.

Clean thoroughly. Remove all dust, oil, and loose material. Oil-soaked concrete must be cut out — grout will not bond to it.

Check the anchor bolts : correct pattern, correct projection, threads protected and undamaged, and sleeves packed with a compressible material so grout cannot enter and lock the bolt.

Verify top-of-concrete elevation against the foundation drawing, allowing for the planned grout thickness.

Setting and leveling

Baseplates are set on leveling jackscrews , shims and wedges , or a combination. The procedure:

Lower the baseplate over the anchor bolts, keeping it free to move.

Bring it to the correct elevation and position against the layout lines established in Chapter 4.

Level the machined mounting surfaces — not the top of the baseplate skirt — with a precision level. The target is on the order of 0.002 inch per foot , and the mounting pads for the driver and the driven machine must be coplanar within a similar tolerance.

Check level in both directions, and check the diagonals for twist. A baseplate can be level along each axis and still be wound like a propeller.

Snug the anchor bolts only lightly. Tightening them before grouting pulls the baseplate down onto the jackscrews and distorts it.

Do not attempt to correct a warped or damaged baseplate with the anchor bolts. If the pads are not coplanar, they are machined coplanar, in place if necessary.

Grouting

Grout type Compressive strength Characteristics

Cementitious (non-shrink) Moderate Inexpensive, tolerant of damp surfaces, longer cure, less chemical resistance

Epoxy High Excellent chemical and oil resistance, no shrinkage, superior bond and vibration damping; sensitive to temperature and surface preparation

Epoxy grout is the standard for rotating equipment in process plants, especially where oil exposure or vibration is a concern.

Placement practice:

Build forms tight and sealed, with a head box on one side so grout can be poured from one point at a sufficient head to push air ahead of it.

Pour from one side only , letting the grout flow across and out the other side. Pouring from both ends traps air in the middle, and an air void under a machine pad defeats the entire purpose.

Vent holes in the baseplate let trapped air escape; grout holes let it be placed. Both are required on any baseplate large enough to trap air.

Do not vibrate epoxy grout the way concrete is vibrated; it entrains air. Chain-drag or strap it into place per the manufacturer.

Observe the temperature window. Epoxy grout has a minimum and maximum placement temperature and a pot life that shortens sharply as temperature rises.

Chamfer the exposed edges of the cured grout at about 45 degrees to prevent edge chipping and stress cracking.

After the grout cures

Back off or remove the jackscrews. If they are left bearing, the machine load sits on four small points instead of the grout, and the baseplate will flex. Screws that are left in place must be backed clear and the holes sealed.

Torque the anchor bolts to the specified value in a crisscross pattern.

Re-check level on the mounting pads. Any change indicates the grout was not supporting the baseplate uniformly.

Sound the grout with a hammer across the whole area. A hollow ring means a void, which must be pressure injected with epoxy.

Record elevations, level readings, grout type and batch, cure conditions, and final anchor bolt torque.

Soleplates

A soleplate is a flat machined plate grouted into the foundation, with the machine feet bolted directly to it rather than to a fabricated baseplate. Soleplates are used under large machines, under individually mounted bearing pedestals, and where field machining of a single flat surface is easier than fabricating a full base. The setting, leveling, and grouting principles are identical; the tolerance on flatness and coplanarity is usually tighter, because the soleplate is the mounting surface.