Study guide
9.2 Reverse Dial Indicator Alignment
NCCER Industrial Maintenance Mechanic Exam
Track your progress as you read
Finished sections get a check mark.
1 The NCCER Industrial Maintenance Mechanic Assessment
1.1 The IMM Journey-Level Credential and Assessment Specification 1.2 The Nine Content Domains: Item Counts and a Study Plan
2 Industrial Maintenance Mechanic Fundamentals
2.1 Safety Programs, PPE, and Hazard Communication 2.2 Hazardous Energy Control: Lockout/Tagout and Confined Space Entry 2.3 Tools of the Trade: Hand and Power Tools 2.4 Oxyfuel Cutting: Equipment, Safe Setup, and Cutting Practice 2.5 Ferrous Metal Piping Practices: Cutting, Threading, and Joining
3 Rigging and Mobile Equipment
3.1 Slings, Rigging Hardware, and Inspection Criteria 3.2 Load Weight, Center of Gravity, Sling Angle, and Hand Signals 3.3 Mobile and Support Equipment: Forklifts, Aerial Lifts, and Mobile Cranes
4 Craft Mathematics, Layout, and Precision Measurement
4.1 Craft-Related Mathematics: Fractions, Units, Area, and Volume 4.2 Advanced Trade Math: Right Triangles, Trigonometry, and Pipe Offsets 4.3 Basic Layout: Squaring, Leveling, and Transferring Elevations 4.4 Precision Measuring Tools: Micrometers, Verniers, and Dial Indicators 4.5 Gauges, Tolerances and Fits, and Torque Measurement
5 Construction Drawings and Blueprint Reading
5.1 Reading Construction Drawings: Views, Lines, Scales, and the Title Block 5.2 Orthographic, Isometric, Arrangement, and Foundation Drawings 5.3 Advanced Blueprint Reading: P&IDs, Instrument Tags, and Welding Symbols
6 Valves, Packing, and Mechanical Seals
6.1 Valve Types and Service Selection 6.2 Valve Construction, Markings, Pressure Classes, and Actuators 6.3 Removing and Installing Valves: Flange Bolting and Torque Sequence 6.4 Valve Maintenance: Packing, Stuffing Boxes, Gaskets, and O-Rings 6.5 Hydrostatic and Pneumatic Testing of Piping and Equipment 6.6 Mechanical Seals: Components, Types, and Installation
7 Bearings, Lubrication, and Couplings
7.1 Bearing Types, Designations, and Selection 7.2 Bearing Lubrication, Handling, and Failure Analysis 7.3 Removing and Installing Bearings: Fits, Heating, and Mounting 7.4 Couplings: Types, Selection, and Installation
8 Pumps, Baseplates, and Mechanical Drives
8.1 Pumps and Drivers: Centrifugal and Positive Displacement 8.2 Setting Baseplates and Soleplates: Leveling, Anchoring, and Grouting 8.3 Prealignment: Soft Foot, Runout, Pipe Strain, and Shims 8.4 Installing Belt and Chain Drives
9 Shaft Alignment: Conventional, Reverse, and Laser
9.1 Conventional Rim-and-Face Dial Indicator Alignment 9.2 Reverse Dial Indicator Alignment 9.3 Laser Shaft Alignment Systems
10 Maintenance Troubleshooting: Method, Pumps, and Gearboxes
10.1 Systematic Troubleshooting and Root Cause Analysis 10.2 Troubleshooting and Repairing Pumps 10.3 Troubleshooting and Repairing Gearboxes
11 Steam Systems, Boilers, and Process Vessels
11.1 Low-Pressure Steam Systems, Traps, and Condensate Return 11.2 High-Pressure Steam Generation and Boiler Auxiliaries 11.3 Distillation Towers, Vessels, and Internals
12 Compressors and Pneumatic Systems
12.1 Air Compressor Types, Operation, and Maintenance 12.2 Compressed Air Treatment, Storage, and Distribution 12.3 FRL Units, Pneumatic Valves, Actuators, and Speed Control
9.2 Reverse Dial Indicator Alignment
Key Takeaways Explain This Topic AI
Reverse dial alignment uses two rim indicators reading each other's shafts, producing two points on each centerline and defining both lines completely.
Because both readings are rim readings, axial shaft float does not corrupt the measurement the way it can corrupt a face reading.
Each rim reading is still twice the offset at that measurement plane, so each is halved before plotting or calculating.
The method suits long spacer couplings and large spans, where a face reading on a small hub diameter would amplify measurement error.
Bracket sag must be measured for each bracket separately and applied to that bracket's bottom reading.
Last updated: September 2026
The idea behind reverse dial
Rim-and-face gets offset from one indicator and angularity from another. The face indicator is the weak link: it reads across a small hub diameter, so a small measurement error becomes a large calculated angle, and any axial float of the shaft during the sweep goes directly into the number.
Reverse dial indicator alignment removes the face indicator entirely. Instead, two brackets are set up so that:
An indicator mounted on shaft A reads the rim of shaft B.
An indicator mounted on shaft B reads the rim of shaft A.
Each rim reading gives the offset between the two centerlines at that measurement plane . Two points on a line define the line. With one offset measured at the A-hub plane and another at the B-hub plane, both shaft centerlines are fully defined, and offset and angularity fall out together.
- Rim and face Reverse dial
- Indicators One rim, one face Two rim
- Sensitive to axial float Yes , through the face reading No
- Accuracy on short hub diameters Degrades Unaffected
- Long spacer couplings Awkward Well suited
- Solution method Direct calculation Graph or calculation
- Setting up
Complete the prealignment checks and lock out both machines.
Mount two brackets so that each indicator reads the rim of the opposite shaft, as far apart as the coupling and bracket rigidity allow. The further apart the two measurement planes are, the more accurate the angular solution becomes.
Measure the sag of each bracket separately on a mandrel. The two brackets rarely sag the same amount, and each correction applies only to its own indicator.
Measure and record three distances — they drive every calculation:
- A: distance between the two measurement planes
- B: distance from the movable machine's near measurement plane to its front foot
- C: distance from that plane to its back foot
Zero both indicators at 12 o'clock.
Rotate both shafts together through 90-degree increments, reading both indicators at each position.
Apply the validity rule — top plus bottom equals left plus right — to each indicator independently . Both must pass.
Correct each bottom reading for its bracket's sag.
Solving graphically
The graphical solution is the traditional approach and the one worth understanding, because it makes the geometry obvious.
Draw a horizontal reference line representing the stationary machine's centerline , extended out past the movable machine's feet.
Choose a horizontal scale for distance and a much larger vertical scale for offset — typically 1 inch of paper per inch of machine horizontally, and 1 inch of paper per 0.005 inch of offset vertically.
Plot the half of each corrected rim reading at its measurement plane, above or below the reference line according to sign.
Draw a straight line through the two plotted points. That line is the movable machine's shaft centerline, projected.
Extend the line to the positions of the front and back feet. The vertical distance from the reference line to the projected centerline at each foot, read off using the vertical scale, is the shim change required at that foot .
The plot is done twice: once from the vertical (12 and 6 o'clock) readings for shimming, and once from the horizontal (3 and 9 o'clock) readings for the sideways move.
Solving by calculation
The same geometry expressed as similar triangles. Using the distances defined above and the two half-readings, the offset at the near plane and the slope between planes project out to each foot: Correction at a foot = Offset at near plane + ( Slope × Distance from near plane to that foot ) \text{Correction at a foot} = \text{Offset at near plane} + \left( \text{Slope} \times \text{Distance from near plane to that foot} \right) Correction at a foot = Offset at near plane + ( Slope × Distance from near plane to that foot )
where the slope is the difference between the two half-readings divided by the distance A between the measurement planes. The result is a positive or negative number at each foot: shim to add or shim to remove.
Modern alignment calculators and laser systems perform exactly this arithmetic; understanding it is what lets a mechanic recognize when a computed answer is nonsense.
Practical points
Bracket rigidity matters more than anything else. Two sloppy brackets spanning a long coupling will produce readings that pass the validity rule and are still wrong. Use the shortest, stiffest brackets the geometry permits.
Do not confuse the two indicators' signs. Each indicator reads the opposite shaft, so a positive reading on one corresponds to the opposite sense on the other. Sketching the machine and marking which indicator is which prevents an entire afternoon of moving the machine the wrong way.
Spacer couplings. With a long spacer, remove the spacer and mount the brackets to span the gap. The long span is an advantage for this method, not an obstacle.
Recheck with bolts torqued and re-verify soft foot after shimming, exactly as in the conventional method.