Study guide

3.1 Fasteners and Anchors

NCCER Millwright Certification Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction

0.1 About the NCCER Millwright Certification 0.2 How to Use This Study Guide

2 Chapter 1: Hand & Power Tools, Cutting

1.1 Millwright Hand Tools 1.2 Millwright Power Tools 1.3 Oxyfuel Cutting

3 Chapter 2: Trade Math, Blueprints & Precision Layout

2.1 Craft-Related Mathematics 2.2 Reading Mechanical Drawings 2.3 Basic Layout 2.4 Precision Measuring Tools

4 Chapter 3: Bearings & Fasteners

3.1 Fasteners and Anchors 3.2 Introduction to Bearings 3.3 Removing and Installing Bearings

5 Chapter 4: Packing, Seals & Gaskets

4.1 Gaskets and Packing 4.2 O-Rings and Non-Mechanical Seals 4.3 Mechanical Seals

6 Chapter 5: Installation Fundamentals — Baseplates, Soleplates & Rigging

5.1 Setting Baseplates and Soleplates 5.2 Rigging Practices

7 Chapter 6: Drives, Conveyors & Gearboxes

6.1 Installing Belt and Chain Drives 6.2 Introduction to Conveyors 6.3 Gearboxes

8 Chapter 7: Pumps, Lubrication & Pump Troubleshooting

7.1 Introduction to Pumps 7.2 Troubleshooting and Repairing Pumps 7.3 Lubrication

9 Chapter 8: Conveyor & Gearbox Troubleshooting, Preventive Maintenance

8.1 Troubleshooting and Repairing Conveyors 8.2 Troubleshooting and Repairing Gearboxes 8.3 Preventive and Predictive Maintenance

10 Chapter 9: Alignment Fundamentals & Dial Indicator Methods

9.1 Couplings and Alignment Fundamentals 9.2 Prealignment and Shim Fabrication 9.3 Dial Indicator Alignment

11 Chapter 10: Advanced Alignment, Laser Methods & Compressor Maintenance

10.1 Laser Alignment 10.2 Optical Layout and Alignment 10.3 Compressors and Compressor Maintenance

12 Chapter 11: Hydraulics & Pneumatics

11.1 Basic Pneumatic Systems 11.2 Basic Hydraulic Systems 11.3 Troubleshooting and Repairing Hydraulic Equipment

3.1 Fasteners and Anchors

Key Takeaways Explain This Topic AI

Module 15103 (Fasteners and Anchors, 12.5 hours) sits in the Bearings and Fasteners domain, worth 8.0% of the 125-item exam.

SAE bolt grade is marked by radial lines on the head: Grade 2 = no lines (~60,000-74,000 psi), Grade 5 = 3 lines (~105,000-120,000 psi), Grade 8 = 6 lines (~150,000 psi).

Thread classes run 1A/1B (loosest) to 3A/3B (tightest); 'A' classes are external threads, 'B' classes are internal threads.

Wedge anchors expand a steel clip at the tip; sleeve anchors expand a surrounding sleeve; epoxy anchors chemically bond a rod with adhesive and require cure time before loading.

Right-hand threads tighten clockwise (the default); left-hand threads are used specifically where normal rotation would back out a right-hand fastener.

Last updated: July 2026

Why Fasteners and Anchors Matter on the Exam

Module 15103, Fasteners and Anchors , is a Millwright Level 1 module (12.5 curriculum hours) and it is scored inside the Bearings and Fasteners domain of AEN15MLWR05 — worth 8.0% of the 125-item exam. That may look like a small slice, but fastener questions are some of the most literal and fact-based on the test: bolt grade markings, thread direction, and anchor-type identification either match a memorized fact or they don't. There is very little ambiguity to reason through, which means these are "free points" if you drill the specifics — and guaranteed misses if you guess.

A millwright who mis-selects a fastener or anchor doesn't just fail a test question — a wedge anchor rated for a light bracket used to hold down a vibrating gearbox base can shear or pull out of the concrete, dropping running equipment. Fastener selection is a real safety decision, not paperwork.

Threaded Fasteners: The Core Vocabulary

A threaded fastener joins parts using a helical thread that converts turning force into clamping force. The main families are bolts (through-holes, mated with a nut), screws (thread directly into a tapped hole), and studs (threaded on both ends, one end permanently set into a component, the other end takes a nut).

Thread standards. Most millwright work in North America uses the Unified National (UN) thread standard:

UNC (Unified National Coarse) — fewer threads per inch, faster to start, more tolerant of dirt and minor thread damage. Default choice for general-purpose fastening.

UNF (Unified National Fine) — more threads per inch, higher resistance to loosening from vibration, used where a fine adjustment or high clamp load is needed.

Metric (ISO, International Organization for Standardization) threads — designated by diameter and pitch, e.g., M12 x 1.75.

Thread classes describe the tightness of fit between mating threads:

Classes 1A, 2A, 3A apply to external threads (bolts, studs).

Classes 1B, 2B, 3B apply to internal threads (nuts, tapped holes).

Class 1 is the loosest fit (easy assembly, more play); Class 3 is the tightest, closest-tolerance fit used in precision or high-load work. The exam commonly tests that "1A/1B = loosest, 3A/3B = tightest" pairing.

Thread direction. A right-hand thread tightens clockwise ("righty-tighty") when viewed from the head end — this is the default on the vast majority of millwright hardware. A left-hand thread tightens counterclockwise and is used deliberately where normal rotation (such as a shaft spinning in service) would otherwise back a right-hand fastener out — for example, on the left-hand pedal of a bicycle or the packing nut on some rotating equipment.

Bolt Grade Markings — A High-Yield Fact Set

SAE (Society of Automotive Engineers) bolt grades are stamped as radial lines on the bolt head , and the exam loves this table because it's unambiguous:

  • SAE Grade Head Markings Material Approx. Tensile Strength
  • Grade 2 No lines (plain head) Low/medium carbon steel 60,000-74,000 psi
  • Grade 5 3 radial lines Medium carbon steel, quenched & tempered ~105,000-120,000 psi
  • Grade 8 6 radial lines Alloy steel, quenched & tempered ~150,000 psi

More lines mean a stronger bolt — this is the opposite of what many trainees guess on first exposure (they expect "more marks = weaker" or assume the marks count nuts, not lines). Metric fasteners use a different system: a property class number stamped on the head, such as 8.8 , 10.9 , or 12.9 — the first number (x100) is roughly the tensile strength in MPa, and the decimal is the yield-to-tensile ratio. Never mix a Grade 2 bolt into an application engineered for Grade 8 — visually similar bolts can have less than half the rated strength.

Non-Threaded and Special Fasteners

Not everything a millwright installs has threads. Common non-threaded fasteners include:

Keys — square keys, Woodruff keys (self-aligning on tapered shafts), and gib-head keys (angled head for easy removal) — transmit torque between a shaft and hub without relying on friction alone.

Pins — cotter pins (bent through a drilled hole to lock a nut), dowel pins (precisely locate mating parts, as used to lock final alignment on machine baseplates), roll pins and taper pins.

Retaining rings (snap rings) — internal or external rings that seat in a machined groove to hold a bearing, gear, or shaft component axially in place.

Rivets, clamps, and tie wraps — used for lighter assembly and cable/hose management rather than structural clamping.

Special threaded fasteners worth knowing: set screws (thread into a hub and bear directly against a shaft, often used with a flat or cupped point to lock a pulley or collar), U-bolts , and studs used where a blind or high-vibration joint makes a through-bolt impractical.

Anchors: Fastening Into Concrete

Anchors let a millwright fasten equipment bases into a concrete floor or foundation. The exam tests the mechanism each anchor uses to develop holding power:

Anchor Type How It Holds

Wedge anchor A steel clip at the tip expands and wedges against the sides of the drilled hole as the bolt is tightened

Sleeve anchor An expanding sleeve surrounds the entire anchor body and compresses outward against the hole as the nut is torqued

Drop-in anchor An internally threaded shell is set flush, then expanded with a setting tool; accepts a separate bolt afterward

Epoxy (chemical) anchor A two-part adhesive is injected into the drilled hole; a threaded rod is inserted and the epoxy chemically bonds it to the concrete as it cures

Epoxy anchors need adequate cure time before load is applied — installing equipment and torquing it down before the epoxy has cured to its rated strength is a common field mistake that shows up in scenario-style exam questions.

Torque and Locking Practices

A torque wrench verifies that a fastener has reached its designed clamping force — under-torquing leaves a joint loose and prone to vibration loosening; over-torquing can stretch or shear the fastener or crush a gasket. Torque specs assume clean, dry, unlubricated threads unless the spec explicitly calls for lubrication (lubricated threads develop more clamp force for the same torque reading, so using the wrong assumption over-clamps the joint). Thread-locking compound (such as Loctite) and lock washers are added where vibration would otherwise back a fastener out over time — a classic failure mode on machinery baseplates and coupling guards.

Exam Traps to Watch

Confusing UNC vs. UNF : coarse threads are the general-purpose default; fine threads resist vibration loosening and allow finer adjustment.

Assuming radial lines on a bolt head mean it is weaker — more lines means stronger .

Mixing up which anchor "expands a sleeve" (sleeve anchor) versus which one "wedges a clip" (wedge anchor) — the exam frequently swaps these two in distractor options.

Forgetting that epoxy anchors need cure time before loading.