Study guide
7.2 Troubleshooting and Repairing Pumps
NCCER Millwright Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction
0.1 About the NCCER Millwright Certification 0.2 How to Use This Study Guide
2 Chapter 1: Hand & Power Tools, Cutting
1.1 Millwright Hand Tools 1.2 Millwright Power Tools 1.3 Oxyfuel Cutting
3 Chapter 2: Trade Math, Blueprints & Precision Layout
2.1 Craft-Related Mathematics 2.2 Reading Mechanical Drawings 2.3 Basic Layout 2.4 Precision Measuring Tools
4 Chapter 3: Bearings & Fasteners
3.1 Fasteners and Anchors 3.2 Introduction to Bearings 3.3 Removing and Installing Bearings
5 Chapter 4: Packing, Seals & Gaskets
4.1 Gaskets and Packing 4.2 O-Rings and Non-Mechanical Seals 4.3 Mechanical Seals
6 Chapter 5: Installation Fundamentals — Baseplates, Soleplates & Rigging
5.1 Setting Baseplates and Soleplates 5.2 Rigging Practices
7 Chapter 6: Drives, Conveyors & Gearboxes
6.1 Installing Belt and Chain Drives 6.2 Introduction to Conveyors 6.3 Gearboxes
8 Chapter 7: Pumps, Lubrication & Pump Troubleshooting
7.1 Introduction to Pumps 7.2 Troubleshooting and Repairing Pumps 7.3 Lubrication
9 Chapter 8: Conveyor & Gearbox Troubleshooting, Preventive Maintenance
8.1 Troubleshooting and Repairing Conveyors 8.2 Troubleshooting and Repairing Gearboxes 8.3 Preventive and Predictive Maintenance
10 Chapter 9: Alignment Fundamentals & Dial Indicator Methods
9.1 Couplings and Alignment Fundamentals 9.2 Prealignment and Shim Fabrication 9.3 Dial Indicator Alignment
11 Chapter 10: Advanced Alignment, Laser Methods & Compressor Maintenance
10.1 Laser Alignment 10.2 Optical Layout and Alignment 10.3 Compressors and Compressor Maintenance
12 Chapter 11: Hydraulics & Pneumatics
11.1 Basic Pneumatic Systems 11.2 Basic Hydraulic Systems 11.3 Troubleshooting and Repairing Hydraulic Equipment
7.2 Troubleshooting and Repairing Pumps
Key Takeaways Explain This Topic AI
Work every pump problem as symptom, then likely cause, then corrective action; the same symptom often has more than one valid cause
Worn wear rings increase internal recirculation from discharge back to suction, silently reducing both head and flow over time
Stagger packing joints 90 degrees apart, seat rings one at a time, and leave a small controlled drip for cooling and lubrication
Mechanical seals depend on a flush plan to cool and lubricate the rotating and stationary lapped faces
Always confirm alignment and correct rotation direction with a bump start before bringing a rebuilt pump to full speed
Last updated: July 2026
Why This Matters
Module 15405, Troubleshooting and Repairing Pumps , is a 17.5-hour hands-on module and the second of the two pump-specific modules on the AEN15MLWR05 blueprint. Where the previous section tested pump theory , this module tests the field skill a millwright is actually hired for: recognizing what a symptom means, disassembling and reassembling a pump correctly, and following a safe startup and shutdown sequence. A large share of the Maintenance and Troubleshooting domain's 26 questions draw on exactly this kind of "symptom leads to cause leads to corrective action" reasoning, so memorizing pump parts alone is not enough — you must be able to work the diagnostic chain.
The Troubleshooting Chart
Symptom Likely Cause Corrective Action
No discharge / won't prime Air in suction line, closed suction valve, clogged strainer, wrong rotation direction, casing not filled Vent air, open valve fully, clean strainer, check rotation against arrow, re-prime casing
Insufficient flow Worn impeller or wear rings (internal recirculation), impeller partially clogged, speed too low, system head higher than design Inspect/replace wear parts, clear impeller, verify motor speed, re-check system curve
Insufficient pressure Worn wear rings, entrained air, undersized impeller, low speed Replace wear rings, eliminate air ingress, verify impeller trim matches spec
Loses prime after running Air leak on suction side, worn packing/seal admitting air on a suction-lift application Pressure-test suction piping, replace packing or seal
Excessive power draw Misalignment, bent shaft, packing too tight, mechanical binding, operating too far right of the curve Re-align, check shaft runout, loosen packing gland, verify system operating point
Noise or vibration Cavitation, misalignment, worn bearings, impeller imbalance Check NPSH margin, re-align, inspect/replace bearings, balance or replace impeller
Overheated bearings Over- or under-lubrication, misalignment, worn bearings Correct grease/oil fill, re-align, inspect bearings
Seal or packing leakage Worn seal faces, wrong or blocked flush, dry packing, scored shaft sleeve Replace seal or packing, verify flush plan, replace sleeve if scored
Wear Rings and Internal Recirculation
A wear ring is a replaceable, close-clearance ring installed between the impeller and the casing (or between impeller hub and casing wear surfaces) that limits how much high-pressure discharge fluid can leak back to the low-pressure suction side. As a pump runs for years, abrasive particles and normal rubbing open up that clearance. The pump keeps spinning at the same speed, but more and more fluid recirculates internally instead of leaving the discharge, so measured head and flow both fall even though nothing else about the pump has visibly changed. This is why "worn wear rings" appears repeatedly in the troubleshooting chart above as the answer to reduced flow and reduced pressure.
Packing vs. Mechanical Seal: Installation and Repair
Repacking a stuffing box follows a strict sequence tested on the exam: cut each packing ring on a 45-degree bias, and stagger the cut joints 90 degrees apart around the shaft as rings are installed (for four rings, joints land roughly at the 12, 3, 6, and 9 o'clock positions). Install and seat rings one at a time with a tamping tool — never push a new ring against un-seated packing beneath it. The gland follower must then seat straight and even, with its neck extending a minimum of 1/8 inch into the stuffing box, tightened only until you feel the packing begin to resist. Properly set packing is allowed a small, controlled drip — that leakage is what lubricates and cools the packing rings; tightening a gland until the leak stops entirely burns up the packing and scores the shaft.
A mechanical seal , by contrast, uses two flat, lapped faces — one rotating with the shaft, one stationary in the housing — held together to create near-zero leakage. Seal faces depend on a thin fluid film for cooling and lubrication, delivered by a flush plan that circulates clean, cool fluid across the faces (for example, an internal recirculation flush or an external clean-fluid flush). A seal installed without proper flush, or one exposed to a dirty or overheated process fluid, will score and fail early — this is the seal equivalent of over-tightening a packing gland.
Disassembly, Reassembly, and Startup Sequence
Lock out and tag out the driver; isolate and drain/depressurize suction and discharge.
Remove the coupling guard and disconnect the coupling; support the pump before unbolting it from the baseplate.
Disassemble the casing, marking orientation, and inspect wear parts — impeller clearance, wear rings, shaft condition, bearings, and seal or packing.
Replace worn components, reassemble in reverse order, and confirm the shaft turns freely by hand before proceeding.
Perform an alignment check before reconnecting the coupling — never couple a pump to its driver and assume alignment is correct.
Prime the casing, vent trapped air, and bump-start briefly to confirm correct rotation direction before a full start.
Bring the pump to full speed while monitoring for abnormal noise, vibration, seal or packing leakage, and motor amperage.
Exam Scenario
A millwright has just rebuilt a centrifugal pump and reinstalled it on its baseplate. Before the first full start, the correct next step is a brief bump start — energizing the motor for a fraction of a second to confirm the shaft turns in the direction marked by the rotation arrow — not immediately running the pump at full speed. Running a rebuilt pump backward, even briefly, can unscrew impeller threads or damage a mechanical seal designed for one direction of rotation.
Key Takeaways
Work every pump problem as symptom → likely cause → corrective action; the same symptom (low flow, low pressure) often has more than one valid cause.
Worn wear rings increase internal recirculation, silently reducing both head and flow over time.
Stagger packing joints 90 degrees, seat rings one at a time, and leave a small controlled drip; never tighten a gland until leakage stops completely.
Mechanical seals depend on a flush plan for cooling and lubrication of the lapped faces.
Always confirm alignment and correct rotation direction (via a bump start) before bringing a rebuilt pump to full speed.