Study guide

10.2 Drifting Loads Between Two Hoists & Load Transfer Principles

NCCER Rigger Basic / Advanced

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Overview, Qualifications & Safety Standards

1.1 NCCER Rigger Certification Structure, Exam Format & Testing Policies 1.2 OSHA 29 CFR 1926 Subpart CC & Qualified Rigger Requirements 1.3 ASME B30 Standards Framework for Rigging & Lifting 1.4 Job-Site Safety, Hazard Identification & Exclusion Zones

2 Chapter 2: Slings & Hitches

2.1 Types of Slings: Synthetic, Wire Rope, Alloy Chain & Metal Mesh 2.2 Basic Rigging Hitches: Vertical, Choker, Basket & Bridles 2.3 Choker Hitch Reductions & Choke Angle Factors 2.4 Basket Hitch Configurations, D/d Ratios & Efficiency

3 Chapter 3: Sling Angles & Tension Calculations

3.1 Principles of Sling Leg Angle & Horizontal Sling Angles 3.2 Sling Tension Formulas & Worked Calculation Examples 3.3 Critical Sling Angles & The 30-Degree Prohibition 3.4 Symmetrical vs. Non-Symmetrical Bridle Leg Tension & Center of Gravity Alignment

4 Chapter 4: Sling Inspection & Removal Criteria

4.1 Wire Rope Sling Inspection & ASME B30.9 Removal Criteria 4.2 Synthetic Web & Round Sling Inspection & Removal Criteria 4.3 Alloy Steel Chain Sling Inspection & Wear Limits 4.4 Metal Mesh & High-Performance Synthetic Slings Inspection

5 Chapter 5: Rigging Hardware & Below-the-Hook Lifting Devices

5.1 Shackles: Types, Application, Loading & ASME B30.26 Inspection 5.2 Eyebolts, Swivel Hoist Rings & Angular Loading Deratings 5.3 Hooks: Types, ASME B30.10 Inspection Criteria & Latch Requirements 5.4 Below-the-Hook Lifting Devices: Spreader Bars, Equalizer Beams & ASME B30.20

6 Chapter 6: Rigging Hardware Connections & Specialty Tools

6.1 Turnbuckles, Rigging Links & Master Rings 6.2 Wire Rope Clips: U-Bolt vs. Fist Grip & Installation Efficiency 6.3 Wedge Sockets & Wire Rope End Terminations 6.4 Snatch Blocks, Sheaves & Lead Line Calculations 6.5 Hoisting & Jacking Equipment: Chain Hoists, Lever Hoists, Winches & Gantries 6.6 Rigging Knots, Fiber Rope & Rope Work for Load Control

7 Chapter 7: Wire Rope Construction, Inspection & Reeving

7.1 Wire Rope Components, Core Types & Lay Classifications 7.2 Crane Hoist Wire Rope Inspection & Retirement Criteria 7.3 Reeving Patterns, Parts of Line & Mechanical Advantage 7.4 Hoist Drum Capacity, Fleet Angle & Minimum Wraps 7.5 Wire Rope Handling, Installation, Storage & Field Maintenance

8 Chapter 8: Load Weight Estimation & Center of Gravity

8.1 Material Densities & Basic Volume Formulas for Riggers 8.2 Load Weight Calculations for Symmetrical & Composite Shapes 8.3 Determining Center of Gravity (CG) for Regular & Irregular Loads 8.4 Center of Gravity Above vs. Below Pick Points & Load Stability

9 Chapter 9: Crane Operations, Safety Devices & Communication

9.1 Mobile Crane Types, Quadrants of Operation & Boom Geometry 9.2 Crane Safety Devices & Operational Aids (A2B, LMI, Level Indicators) 9.3 Standard ASME B30.5 Hand Signals & Radio Communication Protocols 9.4 Power Line Clearances, Weather Limits & Ground Bearing Conditions 9.5 Telescopic Boom Attachments: Swing-Away Extensions, Jibs, Erecting & Stowing 9.6 Crane Assembly & Disassembly: Lattice Boom, Counterweights & the A/D Director 9.7 Crane Safety Devices Out of Service, Emergency Procedures & Responding to Crane Incidents

10 Chapter 10: Advanced Rigging Operations & Lateral Movement

10.1 Lateral Load Movement: Incline Planes, Friction & Required Line Pull 10.2 Drifting Loads Between Two Hoists & Load Transfer Principles 10.3 Inverting, Rolling & Turning Heavy Loads 10.4 Advanced Cribbing, Blocking & Jacking Operations 10.5 Rigging Piping, Pipe Spools & Rebar Bundles

11 Chapter 11: Complex Lift Planning & Multi-Crane Lifts

11.1 Lift Plan Components, Roles & Responsibilities 11.2 Critical Lift Criteria & Engineering Analysis 11.3 Multi-Crane Tandem Lifts: Load Distribution & Synchronization 11.4 Crane Load Chart Deductions: Net vs. Gross Capacity Calculations 11.5 Reading Mobile Crane Load Charts: Configurations, Range Diagrams & Chart Selection

12 Chapter 12: Personnel Hoisting & Site Rigging Management

12.1 OSHA 29 CFR 1926.1431 Personnel Hoisting Regulations & Derating 12.2 Suspended Personnel Platforms: Design, Proof Testing & Trial Lift 12.3 Tagline Safety, Load Control & Line-of-Fire / Pinch-Point Hazards 12.4 Rigging Storage, Maintenance, Documentation & Periodic Inspection Logs

10.2 Drifting Loads Between Two Hoists & Load Transfer Principles

Key Takeaways Explain This Topic AI

Drifting is the controlled horizontal translation of a suspended load between two overhead lifting points (manual chain hoists, lever hoists, or crane hooks) without ground support.

As the horizontal drift angle (θ) increases from vertical (0°), the vector tension on both hoists and their overhead anchor points escalates dramatically due to combined vertical load share and lateral horizontal pull (T_H).

Standard bridge cranes, wire rope hoists, and beam trolleys strictly prohibit lateral side-pulling unless engineered with swiveling suspension and certified angular load ratings under ASME B30.16 and B30.21.

Load transfer mechanics require step-by-step coordination between operators: Hoist A slacks while Hoist B heaves, ensuring neither hoist exceeds its rated Working Load Limit (WLL) at maximum drift angle.

Last updated: August 2026

10.2 Drifting Loads Between Two Hoists & Load Transfer Principles

Drifting is an advanced rigging technique used to move a suspended load horizontally between two overhead lifting points without placing the load on the ground or floor. It is commonly employed inside industrial process plants, pump rooms, boiler houses, and marine engine compartments to navigate heavy components around structural columns, piping headers, cable trays, and mezzanines.

While drifting provides enormous flexibility, it introduces severe multi-axis vector tensions, angular hoist line loads, and lateral structural thrusts on overhead beams. Riggers must calculate peak tensions under ASME B30.16 (Overhead Hoists) , ASME B30.21 (Lever Hoists) , and ASME B30.10 (Hooks) .

Vector Mechanics of Two-Hoist Drifting

When a load is suspended between two hoists (Hoist A and Hoist B) whose lines are angled away from the true vertical, each hoist experiences tension resulting from two vector forces:

The Vertical Component ( T V T_V T V ​ ) , which supports the downward gravitational weight of the load.

The Horizontal Component ( T H T_H T H ​ ) , which balances the opposing lateral pull of the other hoist. [Anchor A] [Anchor B]

  • | |
  • | |
  • Hoist A Hoist B
  • \ [θ_A] [θ_B] /
  • \ /
  • \ /
  • \ /
  • \ /
  • \ /
  • +-------------------------+
  • | LOAD (W) |
  • +-------------------------+
  • Static Equilibrium Equations

For a drifted load suspended in static equilibrium between Hoist A (at angle θ A \theta_A θ A ​ from vertical) and Hoist B (at angle θ B \theta_B θ B ​ from vertical): ∑ F x = 0 ⟹ T A × sin ⁡ ( θ A ) = T B × sin ⁡ ( θ B ) \sum F_x = 0 \implies T_A \times \sin(\theta_A) = T_B \times \sin(\theta_B) ∑ F x ​ = 0 ⟹ T A ​ × sin ( θ A ​ ) = T B ​ × sin ( θ B ​ ) ∑ F y = 0 ⟹ T A × cos ⁡ ( θ A ) + T B × cos ⁡ ( θ B ) = W \sum F_y = 0 \implies T_A \times \cos(\theta_A) + T_B \times \cos(\theta_B) = W ∑ F y ​ = 0 ⟹ T A ​ × cos ( θ A ​ ) + T B ​ × cos ( θ B ​ ) = W

Where:

  • T A T_A T A ​ = Total tension in Hoist line A
  • T B T_B T B ​ = Total tension in Hoist line B
  • θ A \theta_A θ A ​ = Angle of Hoist A line from the true vertical
  • θ B \theta_B θ B ​ = Angle of Hoist B line from the true vertical

W W W = Total weight of the load including rigging hardware +-----------------------------------------------------------------------------------------+

  • | DRIFT ANGLE & VECTOR TENSION MULTIPLICATION TABLE |
  • +-----------------------------------------------------------------------------------------+
  • | ANGLE FROM VERTICAL (θ) | TENSION FACTOR (1 / cos θ) | HORIZONTAL THRUST (tan θ) |
  • +---------------------------+------------------------------+------------------------------+
  • | 0° (Plumb Vertical) | 1.000 | 0.000 |
  • | 15° | 1.035 (+3.5%) | 0.268 (26.8% of vert load) |
  • | 30° | 1.155 (+15.5%) | 0.577 (57.7% of vert load) |
  • | 45° | 1.414 (+41.4%) | 1.000 (100.0% of vert load) |
  • | 60° | 2.000 (+100.0% / DOUBLED) | 1.732 (173.2% of vert load) |
  • +-----------------------------------------------------------------------------------------+

Critical Engineering Warning: When drift angles exceed 45° from vertical , vector tension multiplies exponentially, and horizontal thrust exceeds the vertical weight of the load. Under NCCER and ASME safety standards, drifting angles should never exceed 45° from vertical unless explicitly designed and approved by a qualified structural engineer.

Side-Loading Restrictions & Equipment Limitations

Standard overhead lifting equipment is engineered strictly for axial, vertical lifting. Side-loading creates severe bending moments and equipment failure risks: +-----------------------------------------------------------------------------------------+

  • | EQUIPMENT SIDE-LOADING LIMITS |
  • +-----------------------------------------------------------------------------------------+
  • | 1. Overhead Bridge / Gantry Cranes (ASME B30.2): |
  • | - Prohibits lateral side-pulling. Side-pull causes wire rope to jump drum grooves, |
  • | wear against rope guides, bend the boom tip, or derail beam trolleys. |
  • +-----------------------------------------------------------------------------------------+
  • | 2. Electric / Air Wire Rope Hoists (ASME B30.16): |
  • | - Maximum allowable fleet angle is typically 3° to 5° from vertical. Side-pulling |
  • | will break rope guides and damage drum flanging. |
  • +-----------------------------------------------------------------------------------------+
  • | 3. Manual Chain Fall & Lever Hoists (ASME B30.16 / B30.21): |
  • | - Permitted for drifting ONLY IF equipped with 360° swiveling top and bottom hooks |
  • | that align in a direct straight line between anchor point and load attachment. |
  • | - Chain must enter the load sheave cleanly without binding or twisting against the |
  • | hoist housing guide plates. |
  • +-----------------------------------------------------------------------------------------+
  • | 4. Beam Clamps & Trolley Anchors: |
  • | - Standard rigid beam clamps are rated STRICTLY for 90° vertical loading. |
  • | - When side-loaded at 45°, standard beam clamp capacity is derated by up to 50–75% |
  • | due to flange twisting moments. Universal swivel beam clamps must be used. |
  • +-----------------------------------------------------------------------------------------+

Step-by-Step Worked Calculation: Drifting Machinery +-----------------------------------------------------------------------------------------+

  • | WORKED DRIFTING SCENARIO |
  • +-----------------------------------------------------------------------------------------+
  • | Load: Rotary Air Compressor = 6,000 lbs |
  • | Setup: Drifting horizontally between Hoist A and Hoist B suspended from I-beams |
  • | Initial State: Hoist A is plumb vertical (θ_A = 0°), holding 100% of load (6,000 lbs). |
  • | Mid-Drift State: Load is drifted horizontally until Hoist A is at θ_A = 30° and |
  • | Hoist B is at θ_B = 45°. |
  • +-----------------------------------------------------------------------------------------+

Step 1: Establish Equilibrium Equations Horizontal: T A sin ⁡ ( 30 ∘ ) = T B sin ⁡ ( 45 ∘ ) \text{Horizontal: } T_A \sin(30^\circ) = T_B \sin(45^\circ) Horizontal: T A ​ sin ( 3 0 ∘ ) = T B ​ sin ( 4 5 ∘ ) T A ( 0.500 ) = T B ( 0.7071 ) ⟹ T A = 1.4142 × T B T_A (0.500) = T_B (0.7071) \implies T_A = 1.4142 \times T_B T A ​ ( 0.500 ) = T B ​ ( 0.7071 ) ⟹ T A ​ = 1.4142 × T B ​ Vertical: T A cos ⁡ ( 30 ∘ ) + T B cos ⁡ ( 45 ∘ ) = 6 , 000 lbs \text{Vertical: } T_A \cos(30^\circ) + T_B \cos(45^\circ) = 6,000 \text{ lbs} Vertical: T A ​ cos ( 3 0 ∘ ) + T B ​ cos ( 4 5 ∘ ) = 6 , 000 lbs T A ( 0.8660 ) + T B ( 0.7071 ) = 6 , 000 lbs T_A (0.8660) + T_B (0.7071) = 6,000 \text{ lbs} T A ​ ( 0.8660 ) + T B ​ ( 0.7071 ) = 6 , 000 lbs

Step 2: Substitute T A T_A T A ​ to Solve for T B T_B T B ​ (Hoist B Tension) ( 1.4142 × T B ) ( 0.8660 ) + T B ( 0.7071 ) = 6 , 000 (1.4142 \times T_B)(0.8660) + T_B (0.7071) = 6,000 ( 1.4142 × T B ​ ) ( 0.8660 ) + T B ​ ( 0.7071 ) = 6 , 000 1.2247 × T B + 0.7071 × T B = 6 , 000 1.2247 \times T_B + 0.7071 \times T_B = 6,000 1.2247 × T B ​ + 0.7071 × T B ​ = 6 , 000 1.9318 × T B = 6 , 000 1.9318 \times T_B = 6,000 1.9318 × T B ​ = 6 , 000 T B = 6 , 000 1.9318 = 3 , 106 lbs T_B = \frac{6,000}{1.9318} = \mathbf{3,106 \text{ lbs}} T B ​ = 1.9318 6 , 000 ​ = 3 , 106 lbs

Step 3: Solve for T A T_A T A ​ (Hoist A Tension) T A = 1.4142 × 3 , 106 lbs = 4 , 393 lbs T_A = 1.4142 \times 3,106 \text{ lbs} = \mathbf{4,393 \text{ lbs}} T A ​ = 1.4142 × 3 , 106 lbs = 4 , 393 lbs

Step 4: Calculate Horizontal Thrust on Overhead Beam Anchors ( F x F_x F x ​ ) F x = T A sin ⁡ ( 30 ∘ ) = 4 , 393 × 0.500 = 2 , 196.5 lbs F_x = T_A \sin(30^\circ) = 4,393 \times 0.500 = \mathbf{2,196.5 \text{ lbs}} F x ​ = T A ​ sin ( 3 0 ∘ ) = 4 , 393 × 0.500 = 2 , 196.5 lbs

Check with Hoist B: F x = T B sin ⁡ ( 45 ∘ ) = 3 , 106 × 0.7071 = 2 , 196.3 lbs F_x = T_B \sin(45^\circ) = 3,106 \times 0.7071 = 2,196.3 \text{ lbs} F x ​ = T B ​ sin ( 4 5 ∘ ) = 3 , 106 × 0.7071 = 2 , 196.3 lbs (Balances perfectly).

Step 5: Evaluate Combined Loading on Hoists and Beam

Total line tension supported across both hoists = 4 , 393 + 3 , 106 = 7 , 499 lbs = 4,393 + 3,106 = \mathbf{7,499 \text{ lbs}} = 4 , 393 + 3 , 106 = 7 , 499 lbs (a 25% increase over the static 6,000 lb load weight due to vector angles).

The overhead runway beams experience an inward horizontal bending force of 2,197 lbs , requiring verification that beam flanges and bracing resist lateral deflection.

Drifting Execution Protocol & Step-by-Step Transfer

Drifting requires precise, coordinated command execution between the rigger-in-charge and hoist operators: DRIFTING SEQUENCE

  • +-----------------------------------------------------------------------------------------+
  • | 1. RIGGING & PRE-TENSION: |
  • | - Connect Hoist B to load attachment point using certified rigging hardware. |
  • | - Take up all slack in Hoist B until line is snug (pre-tensioned). |
  • +-----------------------------------------------------------------------------------------+
  • | 2. INCREMENTAL TRANSFER (HEAVE B / SLACK A): |
  • | - Signal Hoist B operator: "HEAVE (LIFT) 2 INCHES". |
  • | - Signal Hoist A operator: "SLACK (LOWER) 2 INCHES". |
  • | - Maintain continuous load trajectory; observe drift angles and headroom clearance. |
  • +-----------------------------------------------------------------------------------------+
  • | 3. MAXIMUM ANGLE MONITORING: |
  • | - Continually verify that drift angles remain within planned calculation limits. |
  • | - Verify hook throat openings and chain links remain unjammed and freely aligned. |
  • +-----------------------------------------------------------------------------------------+
  • | 4. COMPLETE TRANSFER TO HOIST B: |
  • | - Continue cycle until load is positioned directly beneath Hoist B. |
  • | - Hoist A is completely slacked and detached; Hoist B assumes 100% vertical load. |
  • +-----------------------------------------------------------------------------------------+

Loading diagram... Two-Hoist Drifting Mechanics, Angle Factors & Execution