Study guide

6.5 Hoisting & Jacking Equipment: Chain Hoists, Lever Hoists, Winches & Gantries

NCCER Rigger Basic / Advanced

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Overview, Qualifications & Safety Standards

1.1 NCCER Rigger Certification Structure, Exam Format & Testing Policies 1.2 OSHA 29 CFR 1926 Subpart CC & Qualified Rigger Requirements 1.3 ASME B30 Standards Framework for Rigging & Lifting 1.4 Job-Site Safety, Hazard Identification & Exclusion Zones

2 Chapter 2: Slings & Hitches

2.1 Types of Slings: Synthetic, Wire Rope, Alloy Chain & Metal Mesh 2.2 Basic Rigging Hitches: Vertical, Choker, Basket & Bridles 2.3 Choker Hitch Reductions & Choke Angle Factors 2.4 Basket Hitch Configurations, D/d Ratios & Efficiency

3 Chapter 3: Sling Angles & Tension Calculations

3.1 Principles of Sling Leg Angle & Horizontal Sling Angles 3.2 Sling Tension Formulas & Worked Calculation Examples 3.3 Critical Sling Angles & The 30-Degree Prohibition 3.4 Symmetrical vs. Non-Symmetrical Bridle Leg Tension & Center of Gravity Alignment

4 Chapter 4: Sling Inspection & Removal Criteria

4.1 Wire Rope Sling Inspection & ASME B30.9 Removal Criteria 4.2 Synthetic Web & Round Sling Inspection & Removal Criteria 4.3 Alloy Steel Chain Sling Inspection & Wear Limits 4.4 Metal Mesh & High-Performance Synthetic Slings Inspection

5 Chapter 5: Rigging Hardware & Below-the-Hook Lifting Devices

5.1 Shackles: Types, Application, Loading & ASME B30.26 Inspection 5.2 Eyebolts, Swivel Hoist Rings & Angular Loading Deratings 5.3 Hooks: Types, ASME B30.10 Inspection Criteria & Latch Requirements 5.4 Below-the-Hook Lifting Devices: Spreader Bars, Equalizer Beams & ASME B30.20

6 Chapter 6: Rigging Hardware Connections & Specialty Tools

6.1 Turnbuckles, Rigging Links & Master Rings 6.2 Wire Rope Clips: U-Bolt vs. Fist Grip & Installation Efficiency 6.3 Wedge Sockets & Wire Rope End Terminations 6.4 Snatch Blocks, Sheaves & Lead Line Calculations 6.5 Hoisting & Jacking Equipment: Chain Hoists, Lever Hoists, Winches & Gantries 6.6 Rigging Knots, Fiber Rope & Rope Work for Load Control

7 Chapter 7: Wire Rope Construction, Inspection & Reeving

7.1 Wire Rope Components, Core Types & Lay Classifications 7.2 Crane Hoist Wire Rope Inspection & Retirement Criteria 7.3 Reeving Patterns, Parts of Line & Mechanical Advantage 7.4 Hoist Drum Capacity, Fleet Angle & Minimum Wraps 7.5 Wire Rope Handling, Installation, Storage & Field Maintenance

8 Chapter 8: Load Weight Estimation & Center of Gravity

8.1 Material Densities & Basic Volume Formulas for Riggers 8.2 Load Weight Calculations for Symmetrical & Composite Shapes 8.3 Determining Center of Gravity (CG) for Regular & Irregular Loads 8.4 Center of Gravity Above vs. Below Pick Points & Load Stability

9 Chapter 9: Crane Operations, Safety Devices & Communication

9.1 Mobile Crane Types, Quadrants of Operation & Boom Geometry 9.2 Crane Safety Devices & Operational Aids (A2B, LMI, Level Indicators) 9.3 Standard ASME B30.5 Hand Signals & Radio Communication Protocols 9.4 Power Line Clearances, Weather Limits & Ground Bearing Conditions 9.5 Telescopic Boom Attachments: Swing-Away Extensions, Jibs, Erecting & Stowing 9.6 Crane Assembly & Disassembly: Lattice Boom, Counterweights & the A/D Director 9.7 Crane Safety Devices Out of Service, Emergency Procedures & Responding to Crane Incidents

10 Chapter 10: Advanced Rigging Operations & Lateral Movement

10.1 Lateral Load Movement: Incline Planes, Friction & Required Line Pull 10.2 Drifting Loads Between Two Hoists & Load Transfer Principles 10.3 Inverting, Rolling & Turning Heavy Loads 10.4 Advanced Cribbing, Blocking & Jacking Operations 10.5 Rigging Piping, Pipe Spools & Rebar Bundles

11 Chapter 11: Complex Lift Planning & Multi-Crane Lifts

11.1 Lift Plan Components, Roles & Responsibilities 11.2 Critical Lift Criteria & Engineering Analysis 11.3 Multi-Crane Tandem Lifts: Load Distribution & Synchronization 11.4 Crane Load Chart Deductions: Net vs. Gross Capacity Calculations 11.5 Reading Mobile Crane Load Charts: Configurations, Range Diagrams & Chart Selection

12 Chapter 12: Personnel Hoisting & Site Rigging Management

12.1 OSHA 29 CFR 1926.1431 Personnel Hoisting Regulations & Derating 12.2 Suspended Personnel Platforms: Design, Proof Testing & Trial Lift 12.3 Tagline Safety, Load Control & Line-of-Fire / Pinch-Point Hazards 12.4 Rigging Storage, Maintenance, Documentation & Periodic Inspection Logs

6.5 Hoisting & Jacking Equipment: Chain Hoists, Lever Hoists, Winches & Gantries

Key Takeaways Explain This Topic AI

Hand chain hoists are built for straight vertical lifting and must never be side-pulled; lever hoists (come-alongs) are the only manual hoist designed for angular pulling, tensioning, and load positioning.

ASME B30.16 governs overhead hoists (underhung), B30.21 governs lever hoists, and B30.7 governs base-mounted drum hoists (winches) — each has its own inspection cycle and its own prohibition on adding handle extensions or "cheater bars."

A winch or air tugger is rated on the bare first layer of rope; every added layer increases the effective drum diameter and drops available line pull by roughly 8-12 percent per layer.

Hydraulic jacks, gantry systems, and cantilever bars carry compressive and overturning loads, not just vertical load: jacks require a rated, level, non-crushing base, and gantry legs must be squared, pinned, and set on load-distributing mats.

Never leave a load supported only by a hoist, jack, or hydraulic cylinder — follow every lift with blocking or a mechanical lock collar.

Last updated: August 2026

6.5 Hoisting & Jacking Equipment: Chain Hoists, Lever Hoists, Winches & Gantries

"Hoisting and jacking equipment" appears as an explicit topic bullet on both the NCCER Rigger and Advanced Rigger written assessment specifications, and the Advanced specification adds "rigging equipment and hoists to move loads" and "special rigging equipment (gantry systems, cantilever bar)." These are the machines a rigger reaches for when a crane cannot get to the load — inside a turbine hall, under a pipe rack, in a compressor building with a 14-foot ceiling.

The unifying exam theme is simple: each device is rated for one direction of pull, and each has a specific prohibition attached to it. Learn the device, the governing standard, and the prohibition.

Manual Hoists: Chain Falls vs. Lever Hoists

  • Feature Hand Chain Hoist ("chain fall") Lever Hoist ("come-along", ratchet puller)
  • Governing standard ASME B30.16 (overhead hoists, underhung) ASME B30.21 (lever hoists)
  • Operator input Endless hand chain pulled hand-over-hand Short ratcheting lever handle
  • Designed direction of pull Vertical only Any direction — vertical, horizontal, or angled
  • Typical capacity range 1/2 to 20 tons 3/4 to 9 tons
  • Primary job Slow, controlled vertical lifting and holding Tensioning, pulling, positioning, load-and-hold

Key prohibition Never side-pull; never use the hoist chain as a sling or choker Never add a pipe or "cheater bar" to the handle

The cheater-bar rule is the single most-tested lever hoist fact. A lever hoist handle is a calibrated moment arm: the length of the handle is what limits how much load an operator can physically apply. Slipping a length of pipe over the handle multiplies that moment far beyond the design factor and is the classic cause of a snapped load chain or a stripped ratchet pawl. If one worker on the standard handle cannot move the load, the load is too heavy — get a bigger hoist.

Manual hoist pre-use checks

Identification and capacity tag legible on the body. A hoist with no legible rated capacity is out of service.

Load chain free of gouges, nicks, stretch, twists, and weld splatter, correctly seated in the load sheave, and not twisted between the hook and the body.

Bottom-block and top hooks within ASME B30.10 limits (no more than 5% throat spread, no more than 10 degrees twist) with functioning latches.

Brake test: lift the load a few inches, stop, and confirm the load holds without creep before continuing.

No welding, heating, or field modification anywhere on the hoist or its chain.

Base-Mounted Drum Hoists, Winches & Air Tuggers

Base-mounted drum hoists (ASME B30.7) and pneumatic tuggers are the workhorses for horizontal pulling, skidding, and reeved lifting through blocks. Three rules dominate the exam:

Rated line pull is a bare-drum number. Manufacturer ratings are given for the first layer of wire rope on the drum. Each additional layer increases the effective drum radius, reducing torque advantage, so available line pull falls by roughly 8-12 percent per layer . A tugger rated 8,000 lb on the first layer may deliver well under 6,000 lb on the fourth.

Anchor the winch to the structure, not to convenience. The winch base, its fasteners, and the anchor point must all be rated for the resultant pull, and the lead line should approach the drum inside the allowable fleet angle so the rope spools evenly.

Keep dead wraps on the drum. Never spool a drum down to the anchor clamp. As with a crane hoist drum, the friction of the remaining wraps — not the anchor bolt — is what actually holds the line.

Application note: rigging a snatch block into the pull line lets a tugger change direction and gain mechanical advantage, but it multiplies the load on the block anchor. Section 6.4 covers the resultant-load vector math you must run on every block anchor.

Hydraulic Jacks & Jacking Systems

Jacks are lifting devices with almost no lateral tolerance. The rigger controls four variables:

Variable Requirement

Base Level, solid, and large enough that jack base pressure does not exceed the bearing capacity of the surface. Use steel plate or hardwood pads on concrete or soil.

Plumb The ram must be truly vertical under the lift point. An out-of-plumb jack develops a side force and can shoot out from under the load.

Lift point A designed, flat, non-crushing bearing surface on the load — never sheet metal, never a pipe wall, never a flange edge.

Follow-up support Blocking or cribbing built up continuously as the load rises ("lift an inch, crib an inch"), or a threaded mechanical lock collar run down against the cylinder.

Common families are the bottle jack (high capacity, short stroke), the journal/track jack (rugged, mechanical, low profile), the toe jack (lifts loads sitting flat on the deck with almost no clearance), and synchronized multi-point hydraulic systems (used to lift a vessel or module at four or more points with a single pump and matched-flow valves so the load stays level).

Gantry Systems & Cantilever Bars

The Advanced Rigger specification calls out gantry systems and the cantilever bar as special rigging equipment.

A portable hydraulic gantry is a self-contained lifting frame: two or four hydraulic legs on rolling bases carrying a header beam with a trolley. It lets a crew lift and travel heavy equipment inside a building with no crane. Legs must be squared, pinned, and set on mats that spread the wheel load , the header beam must not be side-loaded, and travel is only permitted with the load at the minimum practical height. Gantry capacity drops as the legs are extended — always read the capacity chart for the set height and beam span you are actually using , not the headline rating.

A cantilever bar (also called an offset or extension bar) shifts a hook point outboard of the crane hook so a load can be picked past an obstruction or so an offset center of gravity can be reached. Because it deliberately builds a moment arm, it is an engineered below-the-hook device under ASME B30.20: it must be marked with its rated load, its own weight, and the specific pick-point geometry it was designed for, and it must be deducted from crane capacity like any other below-the-hook device.

Exam trap: gantries and cantilever bars are below-the-hook / lifting equipment , so their self-weight is always part of the gross load. A 3,400 lb gantry header does not reduce what the gantry can lift, but a 900 lb cantilever bar absolutely reduces what the crane can lift.

Loading diagram... Selecting Hoisting & Jacking Equipment by Task