Study guide
6.6 Rigging Knots, Fiber Rope & Rope Work for Load Control
NCCER Rigger Basic / Advanced
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Overview, Qualifications & Safety Standards
1.1 NCCER Rigger Certification Structure, Exam Format & Testing Policies 1.2 OSHA 29 CFR 1926 Subpart CC & Qualified Rigger Requirements 1.3 ASME B30 Standards Framework for Rigging & Lifting 1.4 Job-Site Safety, Hazard Identification & Exclusion Zones
2 Chapter 2: Slings & Hitches
2.1 Types of Slings: Synthetic, Wire Rope, Alloy Chain & Metal Mesh 2.2 Basic Rigging Hitches: Vertical, Choker, Basket & Bridles 2.3 Choker Hitch Reductions & Choke Angle Factors 2.4 Basket Hitch Configurations, D/d Ratios & Efficiency
3 Chapter 3: Sling Angles & Tension Calculations
3.1 Principles of Sling Leg Angle & Horizontal Sling Angles 3.2 Sling Tension Formulas & Worked Calculation Examples 3.3 Critical Sling Angles & The 30-Degree Prohibition 3.4 Symmetrical vs. Non-Symmetrical Bridle Leg Tension & Center of Gravity Alignment
4 Chapter 4: Sling Inspection & Removal Criteria
4.1 Wire Rope Sling Inspection & ASME B30.9 Removal Criteria 4.2 Synthetic Web & Round Sling Inspection & Removal Criteria 4.3 Alloy Steel Chain Sling Inspection & Wear Limits 4.4 Metal Mesh & High-Performance Synthetic Slings Inspection
5 Chapter 5: Rigging Hardware & Below-the-Hook Lifting Devices
5.1 Shackles: Types, Application, Loading & ASME B30.26 Inspection 5.2 Eyebolts, Swivel Hoist Rings & Angular Loading Deratings 5.3 Hooks: Types, ASME B30.10 Inspection Criteria & Latch Requirements 5.4 Below-the-Hook Lifting Devices: Spreader Bars, Equalizer Beams & ASME B30.20
6 Chapter 6: Rigging Hardware Connections & Specialty Tools
6.1 Turnbuckles, Rigging Links & Master Rings 6.2 Wire Rope Clips: U-Bolt vs. Fist Grip & Installation Efficiency 6.3 Wedge Sockets & Wire Rope End Terminations 6.4 Snatch Blocks, Sheaves & Lead Line Calculations 6.5 Hoisting & Jacking Equipment: Chain Hoists, Lever Hoists, Winches & Gantries 6.6 Rigging Knots, Fiber Rope & Rope Work for Load Control
7 Chapter 7: Wire Rope Construction, Inspection & Reeving
7.1 Wire Rope Components, Core Types & Lay Classifications 7.2 Crane Hoist Wire Rope Inspection & Retirement Criteria 7.3 Reeving Patterns, Parts of Line & Mechanical Advantage 7.4 Hoist Drum Capacity, Fleet Angle & Minimum Wraps 7.5 Wire Rope Handling, Installation, Storage & Field Maintenance
8 Chapter 8: Load Weight Estimation & Center of Gravity
8.1 Material Densities & Basic Volume Formulas for Riggers 8.2 Load Weight Calculations for Symmetrical & Composite Shapes 8.3 Determining Center of Gravity (CG) for Regular & Irregular Loads 8.4 Center of Gravity Above vs. Below Pick Points & Load Stability
9 Chapter 9: Crane Operations, Safety Devices & Communication
9.1 Mobile Crane Types, Quadrants of Operation & Boom Geometry 9.2 Crane Safety Devices & Operational Aids (A2B, LMI, Level Indicators) 9.3 Standard ASME B30.5 Hand Signals & Radio Communication Protocols 9.4 Power Line Clearances, Weather Limits & Ground Bearing Conditions 9.5 Telescopic Boom Attachments: Swing-Away Extensions, Jibs, Erecting & Stowing 9.6 Crane Assembly & Disassembly: Lattice Boom, Counterweights & the A/D Director 9.7 Crane Safety Devices Out of Service, Emergency Procedures & Responding to Crane Incidents
10 Chapter 10: Advanced Rigging Operations & Lateral Movement
10.1 Lateral Load Movement: Incline Planes, Friction & Required Line Pull 10.2 Drifting Loads Between Two Hoists & Load Transfer Principles 10.3 Inverting, Rolling & Turning Heavy Loads 10.4 Advanced Cribbing, Blocking & Jacking Operations 10.5 Rigging Piping, Pipe Spools & Rebar Bundles
11 Chapter 11: Complex Lift Planning & Multi-Crane Lifts
11.1 Lift Plan Components, Roles & Responsibilities 11.2 Critical Lift Criteria & Engineering Analysis 11.3 Multi-Crane Tandem Lifts: Load Distribution & Synchronization 11.4 Crane Load Chart Deductions: Net vs. Gross Capacity Calculations 11.5 Reading Mobile Crane Load Charts: Configurations, Range Diagrams & Chart Selection
12 Chapter 12: Personnel Hoisting & Site Rigging Management
12.1 OSHA 29 CFR 1926.1431 Personnel Hoisting Regulations & Derating 12.2 Suspended Personnel Platforms: Design, Proof Testing & Trial Lift 12.3 Tagline Safety, Load Control & Line-of-Fire / Pinch-Point Hazards 12.4 Rigging Storage, Maintenance, Documentation & Periodic Inspection Logs
6.6 Rigging Knots, Fiber Rope & Rope Work for Load Control
Key Takeaways Explain This Topic AI
Every knot reduces the strength of the rope it is tied in: a bowline retains roughly 55-60 percent of rope strength, a figure-eight about 65-75 percent, and a square knot barely 45 percent.
Fiber rope and knots are for load control, hauling, and lashing — they are never a substitute for a rated sling, and a knot must never be tied in a synthetic web sling, roundsling, chain, or wire rope.
The bowline forms a fixed non-slipping loop and is the default tagline and hand-line attachment; the clove hitch backed up with two half hitches secures a line to a round member.
Working load for fiber rope is derived from a design factor of at least 5:1 applied to new rope strength, then further reduced for knots, age, abrasion, UV exposure, and chemical contact.
A rigger controls a load with the tagline, not with their body: the line is held in an open hand and never wrapped, looped, or tied around a wrist, arm, or waist.
Last updated: August 2026
6.6 Rigging Knots, Fiber Rope & Rope Work for Load Control
The NCCER Advanced Rigger written specification lists "taglines and knots for load control" as a Rigging Practices topic, and the Rigger practical examination lists "rigging equipment and knots" as a scored task. Candidates are expected to identify a knot from a picture, name its application, and know what it costs the rope.
The governing principle is boundary-setting: fiber rope and knots control loads; rated slings carry loads. A knot is legitimate on a tagline, a hand line, a lashing, or a temporary anchor lanyard. A knot is never legitimate in a load path.
The Absolute Prohibition
Never tie a knot in a sling. A knot in a synthetic web sling or roundsling cuts its rated strength by 50 percent or more , because the knot forces an extremely tight bend radius and concentrates all tension into the outermost filaments at a single point. Knotting is equally prohibited in wire rope slings and alloy chain slings, where the "knot" is really a kink and permanently destroys the rope or link structure. A sling may only be shortened by an approved method — a proper choker, a rated shortening clutch or grab hook designed for that chain, or a shorter sling.
The Working Knots
Knot / hitch What it does Where a rigger uses it Approximate rope strength retained
Bowline Forms a fixed loop that will not slip or tighten under load, and unties after loading Tagline attachment to a load, hand lines, throwing a loop over a bollard or lug ~55-60%
Figure-eight (and figure-eight on a bight) Strong terminal loop; easy to inspect visually Life-safety-adjacent lines, anchor loops where inspectability matters ~65-75%
Clove hitch Secures a line to a round member; adjustable Attaching a tagline to a pipe or column — always backed up with two half hitches ~60-65%
Two half hitches Quick backup / finishing hitch Backing up a clove hitch; securing a tail ~60-65%
Timber hitch Grips along the length of a round member and releases easily Dragging or lashing timber, poles, and pipe ~65-70%
Round turn and two half hitches Takes load off the knot itself with a full wrap Tying off to a post or ring under sustained tension ~65-75%
Square (reef) knot Joins two lines of equal size for lashing only Binding and lashing — never for joining a load-bearing line ~45%
Sheet bend / double sheet bend Joins two lines of unequal diameter Extending a hand line ~50-55%
The percentages are the exam point. A knot is a controlled bend plus a compression point, and both cost strength. Because the square knot retains the least and capsizes easily when the two lines differ in diameter, it is restricted to lashing. Because the bowline holds a fixed loop and still unties after being loaded, it is the rigger default.
Anatomy vocabulary
Bight — a bend or loop in the rope that does not cross itself.
Standing part — the long, load-carrying section of the line.
Running end (working end) — the free end you tie with.
Dressing — arranging the parts of a finished knot so they lie fair and parallel. An undressed knot loses far more strength than a dressed one and can capsize under shock.
Fiber Rope Selection & Design Factor
- Fiber Strength Stretch Notes for riggers
- Polyester High Low Best all-around tagline material; holds strength when wet; resists UV and acids
Nylon Highest of the common three High (~20%+) Absorbs shock well, but the stored energy makes a parting line dangerous; loses ~10-15% strength when wet; destroyed by acids
Polypropylene Lowest Moderate Floats and resists chemicals, but degrades quickly in sunlight and melts at low temperature
Manila (natural) Low Low Legacy material; rots, mildews, and loses strength unpredictably with age
Fiber rope for rigging service is worked to a design factor of at least 5:1 against the new-rope breaking strength, and that working load must then be reduced further for every degrading condition present:
Knots — apply the efficiency from the table above.
Age and service — rope in service loses strength continuously; there is no way to test it in the field.
Abrasion and glazing — fuzzy, cut, or shiny/melted fibers all mean removal.
UV degradation — chalky, faded, powdery surface fibers on polypropylene or polyester.
Chemical exposure — any acid contact on nylon, any strong caustic contact on polyester.
Shock loading — a rope that has been shock loaded is removed, not re-rated.
Inspect fiber rope by opening the lay : untwist a section and look inside for powdered fiber, broken internal yarns, or discoloration. Powder inside the lay is internal abrasion and is a removal condition even when the outside looks sound.
Rope Work on the Load
Attach to the load structure. A tagline goes on a structural corner, lug, or frame member of the load — never on a sling leg, hook, or shackle, where pulling can change sling geometry or unseat hardware.
Two lines on long members. Long or wind-sensitive items such as beams, trusses, pipe spools, and rebar cages need two taglines at opposite distal ends so the crew can control rotation as well as swing.
Length with clearance in mind. The line must be long enough to keep the handler outside the fall zone and clear of the load path, but not so long that it can foul on the structure, a scaffold, or an energized line. Use non-conductive rope near electrical hazards.
Open hand, never wrapped. The line is held, never wrapped or tied around a wrist, hand, arm, or body. If the load surges, a wrapped line drags the rigger into the line of fire with no way to let go.