Study guide
4.3 Alloy Steel Chain Sling Inspection & Wear Limits
NCCER Rigger Basic / Advanced
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Overview, Qualifications & Safety Standards
1.1 NCCER Rigger Certification Structure, Exam Format & Testing Policies 1.2 OSHA 29 CFR 1926 Subpart CC & Qualified Rigger Requirements 1.3 ASME B30 Standards Framework for Rigging & Lifting 1.4 Job-Site Safety, Hazard Identification & Exclusion Zones
2 Chapter 2: Slings & Hitches
2.1 Types of Slings: Synthetic, Wire Rope, Alloy Chain & Metal Mesh 2.2 Basic Rigging Hitches: Vertical, Choker, Basket & Bridles 2.3 Choker Hitch Reductions & Choke Angle Factors 2.4 Basket Hitch Configurations, D/d Ratios & Efficiency
3 Chapter 3: Sling Angles & Tension Calculations
3.1 Principles of Sling Leg Angle & Horizontal Sling Angles 3.2 Sling Tension Formulas & Worked Calculation Examples 3.3 Critical Sling Angles & The 30-Degree Prohibition 3.4 Symmetrical vs. Non-Symmetrical Bridle Leg Tension & Center of Gravity Alignment
4 Chapter 4: Sling Inspection & Removal Criteria
4.1 Wire Rope Sling Inspection & ASME B30.9 Removal Criteria 4.2 Synthetic Web & Round Sling Inspection & Removal Criteria 4.3 Alloy Steel Chain Sling Inspection & Wear Limits 4.4 Metal Mesh & High-Performance Synthetic Slings Inspection
5 Chapter 5: Rigging Hardware & Below-the-Hook Lifting Devices
5.1 Shackles: Types, Application, Loading & ASME B30.26 Inspection 5.2 Eyebolts, Swivel Hoist Rings & Angular Loading Deratings 5.3 Hooks: Types, ASME B30.10 Inspection Criteria & Latch Requirements 5.4 Below-the-Hook Lifting Devices: Spreader Bars, Equalizer Beams & ASME B30.20
6 Chapter 6: Rigging Hardware Connections & Specialty Tools
6.1 Turnbuckles, Rigging Links & Master Rings 6.2 Wire Rope Clips: U-Bolt vs. Fist Grip & Installation Efficiency 6.3 Wedge Sockets & Wire Rope End Terminations 6.4 Snatch Blocks, Sheaves & Lead Line Calculations 6.5 Hoisting & Jacking Equipment: Chain Hoists, Lever Hoists, Winches & Gantries 6.6 Rigging Knots, Fiber Rope & Rope Work for Load Control
7 Chapter 7: Wire Rope Construction, Inspection & Reeving
7.1 Wire Rope Components, Core Types & Lay Classifications 7.2 Crane Hoist Wire Rope Inspection & Retirement Criteria 7.3 Reeving Patterns, Parts of Line & Mechanical Advantage 7.4 Hoist Drum Capacity, Fleet Angle & Minimum Wraps 7.5 Wire Rope Handling, Installation, Storage & Field Maintenance
8 Chapter 8: Load Weight Estimation & Center of Gravity
8.1 Material Densities & Basic Volume Formulas for Riggers 8.2 Load Weight Calculations for Symmetrical & Composite Shapes 8.3 Determining Center of Gravity (CG) for Regular & Irregular Loads 8.4 Center of Gravity Above vs. Below Pick Points & Load Stability
9 Chapter 9: Crane Operations, Safety Devices & Communication
9.1 Mobile Crane Types, Quadrants of Operation & Boom Geometry 9.2 Crane Safety Devices & Operational Aids (A2B, LMI, Level Indicators) 9.3 Standard ASME B30.5 Hand Signals & Radio Communication Protocols 9.4 Power Line Clearances, Weather Limits & Ground Bearing Conditions 9.5 Telescopic Boom Attachments: Swing-Away Extensions, Jibs, Erecting & Stowing 9.6 Crane Assembly & Disassembly: Lattice Boom, Counterweights & the A/D Director 9.7 Crane Safety Devices Out of Service, Emergency Procedures & Responding to Crane Incidents
10 Chapter 10: Advanced Rigging Operations & Lateral Movement
10.1 Lateral Load Movement: Incline Planes, Friction & Required Line Pull 10.2 Drifting Loads Between Two Hoists & Load Transfer Principles 10.3 Inverting, Rolling & Turning Heavy Loads 10.4 Advanced Cribbing, Blocking & Jacking Operations 10.5 Rigging Piping, Pipe Spools & Rebar Bundles
11 Chapter 11: Complex Lift Planning & Multi-Crane Lifts
11.1 Lift Plan Components, Roles & Responsibilities 11.2 Critical Lift Criteria & Engineering Analysis 11.3 Multi-Crane Tandem Lifts: Load Distribution & Synchronization 11.4 Crane Load Chart Deductions: Net vs. Gross Capacity Calculations 11.5 Reading Mobile Crane Load Charts: Configurations, Range Diagrams & Chart Selection
12 Chapter 12: Personnel Hoisting & Site Rigging Management
12.1 OSHA 29 CFR 1926.1431 Personnel Hoisting Regulations & Derating 12.2 Suspended Personnel Platforms: Design, Proof Testing & Trial Lift 12.3 Tagline Safety, Load Control & Line-of-Fire / Pinch-Point Hazards 12.4 Rigging Storage, Maintenance, Documentation & Periodic Inspection Logs
4.3 Alloy Steel Chain Sling Inspection & Wear Limits
Key Takeaways Explain This Topic AI
Only Grade 80, Grade 100, and Grade 120 alloy steel chains are approved for overhead lifting under ASME B30.9 and OSHA 1926.251; Grade 30, Grade 43, and Grade 70 carbon chains are strictly prohibited.
Alloy chain sling tags must display the manufacturer, grade, nominal size, reach, number of legs, and rated capacity for specified hitches and angles.
Inter-link bearing wear must be measured using calipers and compared against the ASME B30.9 Minimum Allowable Thickness Table; wear exceeding allowable limits requires immediate chain replacement.
A total reach increase exceeding 5% due to stretch/elongation, or individual link binding/loss of articulation, requires immediate sling removal.
Exposure to temperatures exceeding 1000°F (538°C), transverse cracks, severe gouges, bent links, or field welding mandates permanent removal from service.
Last updated: August 2026
Alloy Steel Chain Sling Inspection & Wear Limits
Overhead Lifting Chain Rule: Under OSHA 29 CFR 1926.251(b) and ASME B30.9-1, only alloy steel chains (specifically Grade 80, Grade 100, and Grade 120 ) are approved for overhead lifting applications. Carbon steel chains—such as Grade 30 Proof Coil, Grade 43 High Test, and Grade 70 Transport Binder Chain—are strictly prohibited because they lack the necessary tensile strength, toughness, and elongation before failure.
Alloy steel chain slings are exceptionally durable, impact-resistant, and capable of operating in high-temperature environments that would instantly destroy wire rope or synthetic slings. However, chain slings are subject to inter-link abrasive wear, elongation from overloading, localized gouging, bending deformation, and thermal annealing.
Mandatory Chain Sling Identification Tagging
Every alloy chain sling must be equipped with a durable metal tag permanently attached to the master link. Under ASME B30.9, the tag must contain:
- Manufacturer's name or trademark
- Grade of alloy chain ( Grade 80, 100, or 120 )
- Nominal chain size (e.g., 3/8 in, 1/2 in)
- Number of sling legs (single, 2-leg, 3-leg, or 4-leg)
- Reach (bearing point to bearing point length)
- Rated capacity (WLL) for vertical, choker, and basket/bridle hitches at 60°, 45°, and 30° horizontal angles
- Individual serial number +-------------------------------------------------------+
- | ALLOY CHAIN SLING RATED TAG |
- | MANUFACTURER: PEWAG ALLOY SYSTEMS |
- | GRADE: GRADE 100 (G10) |
- | SIZE: 1/2 INCH (13 MM) REACH: 12 FT 0 IN |
- | TYPE: DOS (Double Leg Sling with Grab Hooks) |
- | RATED CAPACITIES (WLL): |
- | - 60° HORIZONTAL ANGLE: 26,000 LBS |
- | - 45° HORIZONTAL ANGLE: 21,200 LBS |
- | - 30° HORIZONTAL ANGLE: 15,000 LBS |
- | SERIAL NO: AC-99420-100 |
- +-------------------------------------------------------+
- Link-by-Link Inspection Methodology
To inspect an alloy steel chain sling properly, riggers must follow a systematic procedure:
Clean the Chain: Remove heavy oil, grease, dirt, and scale using solvent or wire brushing so metal surfaces are fully visible.
Hang or Stretch the Chain: Lay the chain flat on a clean inspection bench or hang it vertically under low tension.
Individual Link Examination: Examine each link individually across four distinct zones: the inner bearing crowns, the outer crowns, the side barrels, and the factory weld.
Articulation & Flexing Check: Rotate and pivot each link relative to its adjoining links. Links must articulate freely. Any link that binds, sticks, or cannot rotate freely indicates link elongation, bending, or excessive wear. ALLOY CHAIN LINK INSPECTION ZONES
- [ Inter-Link Bearing Crown ] (Primary Wear Zone)
- +-------+
- / | \
- | (o) | (o) | <-- Interlocking Contact Point
- Barrel -->| | |<-- Barrel
- | | |
- \ | /
- +-------+
- ^
- [ Factory Weld Zone ]
- Inter-Link Wear Allowance & Caliper Measurements
Because chain links continuously pivot against each other under heavy loads, wear primarily occurs at the inter-link contact points (bearing crowns) . Secondary wear occurs on the outer barrels from dragging across concrete floors.
Caliper Measurement Protocol
Riggers must measure the link diameter at the narrowest worn section using a calibrated vernier or dial caliper. If the measured thickness at any point on any link is less than the minimum allowable thickness listed in ASME B30.9 Table 9-1.9.4-1 , the entire chain section must be condemned.
ASME B30.9 Minimum Allowable Chain Thickness Table
Nominal Chain Size (in) Nominal Chain Size (mm) Nominal Diameter (d) Minimum Allowable Thickness (dmin) Maximum Permissible Wear
- 7/32 in 5.5 mm 0.219 in 0.189 in 0.030 in (13.7%)
- 9/32 in 7.0 mm 0.281 in 0.229 in 0.052 in (18.5%)
- 5/16 in 8.0 mm 0.312 in 0.260 in 0.052 in (16.7%)
- 3/8 in 10.0 mm 0.375 in 0.316 in 0.059 in (15.7%)
- 1/2 in 13.0 mm 0.500 in 0.425 in 0.075 in (15.0%)
- 5/8 in 16.0 mm 0.625 in 0.534 in 0.091 in (14.6%)
- 3/4 in 20.0 mm 0.750 in 0.635 in 0.115 in (15.3%)
- 7/8 in 22.0 mm 0.875 in 0.741 in 0.134 in (15.3%)
- 1 in 26.0 mm 1.000 in 0.840 in 0.160 in (16.0%)
- 1-1/4 in 32.0 mm 1.250 in 1.000 in 0.250 in (20.0%)
- Elongation, Stretch & Distortion Limits
When an alloy chain sling is subjected to severe overloading or dynamic shock, the steel links stretch beyond their elastic limit into plastic deformation.
Reach Elongation Limit
Maximum Permissible Reach Stretch: If the total reach of a chain sling increases by more than 5% over the original length stamped on the identification tag, the sling must be removed from service immediately.
Individual Link Elongation: Any individual link that has stretched noticeably will exhibit a narrowed inner width, causing adjoining links to pinch and bind. If a link binds, the chain must be condemned even if total reach stretch is under 5%. NORMAL CHAIN LINK ELONGATED / STRETCHED LINK
- +-------+ +---+
- / \ / | \
- | | | | | (Inner width collapses;
- | | | | | links bind and lock)
- \ / \ | /
- +-------+ +---+
- Free articulation Locked / Bound
- Nicks, Gouges, Cracks & Field Welding Prohibitions
Transverse Cracks: Any crack oriented perpendicular to the tensile axis of the link creates an extreme stress riser that causes sudden brittle failure. Links with cracks must be discarded.
Longitudinal Nicks & Gouges: Light longitudinal gouges may be blended out by smooth grinding in the direction of the link barrel, provided the remaining metal thickness does not fall below the minimum allowable thickness listed in the wear table.
Bends and Twists: Any link, hook, or master coupling link that is bent or twisted out of its original plane must be removed.
Prohibition of Field Welding: Under OSHA 1926.251(b)(4), field welding, heating, or brazing on alloy steel chain slings is strictly prohibited . Only mechanical coupling links (such as forged alloy Hammerlocks) or welded assemblies certified by an authorized chain manufacturer may be used.
Corrosion and Chemical Pitting: Severe corrosion pitting reduces the effective cross-sectional area and acts as multiple stress risers.
High-Temperature Thermal Derating
Alloy steel chain slings can operate at elevated temperatures, but their Working Load Limit must be derated according to the manufacturer's and ASME B30.9 thermal reduction table:
- Operating Temperature Range Temporary WLL Reduction (While Hot) Permanent WLL Reduction (After Cooling)
- Up to 400°F (204°C) 0% (Full capacity) None (0%)
- 400°F to 500°F (260°C) 10% Reduction None (0%)
- 500°F to 600°F (316°C) 20% Reduction None (0%)
- 600°F to 700°F (371°C) 30% Reduction None (0%)
- 700°F to 800°F (427°C) 40% Reduction 10% Permanent Loss
- 800°F to 900°F (482°C) 50% Reduction 20% Permanent Loss
- 900°F to 1000°F (538°C) 60% Reduction 30% Permanent Loss
- Above 1000°F (538°C) CRITICAL ANNEALING ZONE REMOVE FROM SERVICE PERMANENTLY