Study guide
2.3 Choker Hitch Reductions & Choke Angle Factors
NCCER Rigger Basic / Advanced
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Overview, Qualifications & Safety Standards
1.1 NCCER Rigger Certification Structure, Exam Format & Testing Policies 1.2 OSHA 29 CFR 1926 Subpart CC & Qualified Rigger Requirements 1.3 ASME B30 Standards Framework for Rigging & Lifting 1.4 Job-Site Safety, Hazard Identification & Exclusion Zones
2 Chapter 2: Slings & Hitches
2.1 Types of Slings: Synthetic, Wire Rope, Alloy Chain & Metal Mesh 2.2 Basic Rigging Hitches: Vertical, Choker, Basket & Bridles 2.3 Choker Hitch Reductions & Choke Angle Factors 2.4 Basket Hitch Configurations, D/d Ratios & Efficiency
3 Chapter 3: Sling Angles & Tension Calculations
3.1 Principles of Sling Leg Angle & Horizontal Sling Angles 3.2 Sling Tension Formulas & Worked Calculation Examples 3.3 Critical Sling Angles & The 30-Degree Prohibition 3.4 Symmetrical vs. Non-Symmetrical Bridle Leg Tension & Center of Gravity Alignment
4 Chapter 4: Sling Inspection & Removal Criteria
4.1 Wire Rope Sling Inspection & ASME B30.9 Removal Criteria 4.2 Synthetic Web & Round Sling Inspection & Removal Criteria 4.3 Alloy Steel Chain Sling Inspection & Wear Limits 4.4 Metal Mesh & High-Performance Synthetic Slings Inspection
5 Chapter 5: Rigging Hardware & Below-the-Hook Lifting Devices
5.1 Shackles: Types, Application, Loading & ASME B30.26 Inspection 5.2 Eyebolts, Swivel Hoist Rings & Angular Loading Deratings 5.3 Hooks: Types, ASME B30.10 Inspection Criteria & Latch Requirements 5.4 Below-the-Hook Lifting Devices: Spreader Bars, Equalizer Beams & ASME B30.20
6 Chapter 6: Rigging Hardware Connections & Specialty Tools
6.1 Turnbuckles, Rigging Links & Master Rings 6.2 Wire Rope Clips: U-Bolt vs. Fist Grip & Installation Efficiency 6.3 Wedge Sockets & Wire Rope End Terminations 6.4 Snatch Blocks, Sheaves & Lead Line Calculations 6.5 Hoisting & Jacking Equipment: Chain Hoists, Lever Hoists, Winches & Gantries 6.6 Rigging Knots, Fiber Rope & Rope Work for Load Control
7 Chapter 7: Wire Rope Construction, Inspection & Reeving
7.1 Wire Rope Components, Core Types & Lay Classifications 7.2 Crane Hoist Wire Rope Inspection & Retirement Criteria 7.3 Reeving Patterns, Parts of Line & Mechanical Advantage 7.4 Hoist Drum Capacity, Fleet Angle & Minimum Wraps 7.5 Wire Rope Handling, Installation, Storage & Field Maintenance
8 Chapter 8: Load Weight Estimation & Center of Gravity
8.1 Material Densities & Basic Volume Formulas for Riggers 8.2 Load Weight Calculations for Symmetrical & Composite Shapes 8.3 Determining Center of Gravity (CG) for Regular & Irregular Loads 8.4 Center of Gravity Above vs. Below Pick Points & Load Stability
9 Chapter 9: Crane Operations, Safety Devices & Communication
9.1 Mobile Crane Types, Quadrants of Operation & Boom Geometry 9.2 Crane Safety Devices & Operational Aids (A2B, LMI, Level Indicators) 9.3 Standard ASME B30.5 Hand Signals & Radio Communication Protocols 9.4 Power Line Clearances, Weather Limits & Ground Bearing Conditions 9.5 Telescopic Boom Attachments: Swing-Away Extensions, Jibs, Erecting & Stowing 9.6 Crane Assembly & Disassembly: Lattice Boom, Counterweights & the A/D Director 9.7 Crane Safety Devices Out of Service, Emergency Procedures & Responding to Crane Incidents
10 Chapter 10: Advanced Rigging Operations & Lateral Movement
10.1 Lateral Load Movement: Incline Planes, Friction & Required Line Pull 10.2 Drifting Loads Between Two Hoists & Load Transfer Principles 10.3 Inverting, Rolling & Turning Heavy Loads 10.4 Advanced Cribbing, Blocking & Jacking Operations 10.5 Rigging Piping, Pipe Spools & Rebar Bundles
11 Chapter 11: Complex Lift Planning & Multi-Crane Lifts
11.1 Lift Plan Components, Roles & Responsibilities 11.2 Critical Lift Criteria & Engineering Analysis 11.3 Multi-Crane Tandem Lifts: Load Distribution & Synchronization 11.4 Crane Load Chart Deductions: Net vs. Gross Capacity Calculations 11.5 Reading Mobile Crane Load Charts: Configurations, Range Diagrams & Chart Selection
12 Chapter 12: Personnel Hoisting & Site Rigging Management
12.1 OSHA 29 CFR 1926.1431 Personnel Hoisting Regulations & Derating 12.2 Suspended Personnel Platforms: Design, Proof Testing & Trial Lift 12.3 Tagline Safety, Load Control & Line-of-Fire / Pinch-Point Hazards 12.4 Rigging Storage, Maintenance, Documentation & Periodic Inspection Logs
2.3 Choker Hitch Reductions & Choke Angle Factors
Key Takeaways Explain This Topic AI
Under ASME B30.9, a standard choker hitch retains 100% of its rated choker capacity (typically 75% of vertical WLL) only when the choke angle is between 120° and 180°.
When the choke angle drops below 120°, intense localized bending stresses develop at the choke point, requiring mandatory derating factors: 90°–119° (87%), 60°–89° (74%), 30°–59° (62%), and 0°–29° (49%).
The complete adjusted Working Load Limit is calculated as: Adjusted WLL = Vertical WLL × 0.75 × Choke Angle Factor × Sling Leg Angle Factor.
A double-wrap choker hitch provides 360° circumferential contact, compressing loose bundles (pipe, tubing, rebar) to prevent center pieces from sliding out.
When using a screw pin shackle to choke a load, always place the sling eye on the shackle pin and run the sling body through the shackle bow to prevent the running line from unscrewing the pin.
Last updated: August 2026
Choker Hitch Reductions & Choke Angle Factors
The choker hitch is one of the most widely used rigging configurations because of its ability to grip cylindrical, bundle-type, and non-structural loads. However, the mechanical geometry of a choker hitch induces severe stress concentrations. Where the sling body passes through the eye or hardware, the sling experiences high-tension loading combined with severe acute bending.
To prevent catastrophic failures, ASME B30.9 mandates strict capacity reductions based on the natural choke angle (angle of choke) formed at the choking point. MEASURING THE CHOKE ANGLE (A)
- |
- | <-- Running Leg to Crane Hook
- |
- +---+---+
- | (Eye) |
- +---+---+
- / \
- / \ <-- Choking Loop around Load
- / A \
- +---------+
- | LOAD |
- +---------+
- Choke Angle A: Measured between the running
leg and the choked loop at the eye/hardware.
1. The Standard 120° to 180° Choke Angle Baseline
When a sling is wrapped around a load of sufficient width, the angle formed at the choke point naturally falls between 120° and 180° . Under ASME B30.9:
The baseline Working Load Limit of a choker hitch is established at 75% (0.75) of the sling's single-leg vertical rated capacity (some synthetic manufacturers publish up to 80%).
For choke angles between 120° and 180° , the choke angle reduction factor is 1.00 (100% of the choker rating) .
2. ASME B30.9 Choke Angle Reduction Factor Table
When lifting narrow loads (e.g., single small-diameter pipes, thin structural beams, or bundled conduit), the sling loop is pulled into an acute geometry, forcing the choke angle below 120°. As the choke angle decreases, the outward radial bursting force and localized bending shear at the eye escalate drastically.
Riggers must apply the following ASME B30.9 reduction factors for choke angles below 120°:
- Choke Angle Range Choke Angle Factor (F_choke) Net Multiplier vs. Single Vertical WLL (0.75 × F_choke)
- 120° to 180° 1.00 (100%) 0.750 (75.0% of Vertical WLL)
- 90° to 119° 0.87 (87%) 0.652 (65.2% of Vertical WLL)
- 60° to 89° 0.74 (74%) 0.555 (55.5% of Vertical WLL)
- 30° to 59° 0.62 (62%) 0.465 (46.5% of Vertical WLL)
- 0° to 29° 0.49 (49%) 0.368 (36.8% of Vertical WLL)
Key Principle: A sling choked at a 20° angle retains less than 37% of its original single-leg vertical rating! Overlooking this reduction factor is a leading cause of rigging failures on NCCER calculations.
- 3. Mathematical Formulas & Calculation Scenarios
- Single-Leg Choker Formula
- Adjusted WLL = Vertical WLL × 0.75 × F_choke
- Multi-Leg Bridle Choker Formula
When a bridle hitch is rigged using choker hitches, riggers must account for both the horizontal sling leg angle (θ) and the choke angle factor (F_choke): Total WLL = N × Vertical WLL × 0.75 × F_choke × sin(θ) Where N is the number of effective load-bearing legs, and θ is the horizontal sling angle.
Calculation Scenario 1: Single Wire Rope Choker on Square Duct
Given: A wire rope sling has a rated single-leg Vertical WLL of 12,000 lbs . It is rigged in a single choker hitch around a steel duct. Because of the duct dimensions, the choke angle is measured at 75° .
- Step 1: Identify Base Choker Capacity: Base Choker WLL = 12,000 lbs × 0.75 = 9,000 lbs
- Step 2: Apply Choke Angle Factor for 75° (Range 60°–89° = 0.74): Adjusted WLL = 9,000 lbs × 0.74 = 6,660 lbs
Conclusion: The safe working load limit for this lift is 6,660 lbs .
Calculation Scenario 2: Two-Leg Synthetic Choker Bridle on Heavy Pipe
Given: A 2-leg polyester web bridle is used to lift a long steel pipe. Each leg has a Vertical WLL of 8,000 lbs . The horizontal sling angle is 60° (sin(60°) = 0.866). The pipe diameter creates a choke angle of 100° on each choke (F_choke = 0.87).
Step 1: Calculate adjusted capacity per leg: Leg WLL = 8,000 lbs × 0.75 × 0.87 × sin(60°) Leg WLL = 8,000 × 0.75 × 0.87 × 0.866 = 4,520.5 lbs
- Step 2: Calculate total bridle capacity (2 legs): Total Bridle WLL = 2 × 4,520.5 lbs = 9,041 lbs
- 4. Double-Wrap Choker Hitch (360° Circumferential Grip)
A standard single choker hitch contacts approximately 180° to 270° of the load circumference, leaving loose space along the sides. When lifting bundles of loose materials (e.g., small-diameter pipe, electrical conduit, reinforcing steel, structural tubing), individual center pieces can easily slide out during transit. DOUBLE-WRAP CHOKER HITCH (360° CONTACT)
- |
- | <-- Running Leg
- |
- +---+---+
- | (Eye) |
- +---+---+
- / \
- | (O) | <-- Sling wraps completely 360°
\_____/ around the bundle before choking!
Operational Advantages
Full 360° Radial Compression: Wraps the sling completely around the entire circumference of the load before passing through the eye, squeezing the bundle uniformly from all directions.
Prevention of Walk / Drift: Prevents the sling from sliding or "walking" along the length of slick, oiled, or painted pipe.
Capacity Rating: The double-wrap choker hitch does NOT double the capacity of the sling. The WLL is still governed by the choker rating and the choke angle reduction factor.
5. Choking Hardware: Sliding Choker Hooks vs. Shackle Pin Roll-Out Hazard
When synthetic or wire rope slings are choked, using dedicated hardware improves safety and prolongs equipment life:
Sliding Choker Hooks
Sliding choker hooks feature a broad, rounded curved saddle that slides freely along the sling body. This eliminates sharp bending radius stresses at the eye and protects synthetic fibers from friction wear.
The Shackle Choker & Pin Roll-Out Hazard
When riggers form a choker hitch using a screw pin shackle, strict adherence to shackle geometry is mandatory: CORRECT CHOKER CONFIGURATION DANGEROUS CONFIGURATION (FATAL ERROR)
- (SAFE & APPROVED) (PROHIBITED)
- |
- (Running Leg) (Running Leg)
- | |
- ( BOW ) [===PIN===]
- / \ / \
- [===PIN===] \ ( BOW )
- | \ | |
- (Sling Eye) \ (Sling Eye) |
- \ |
- v v
Running leg moves through Running leg rolls across PIN!
smooth static bow. Pin Friction unscrews the pin
CANNOT unscrew! under load --> TOTAL DROP!
The Rule: Always place the sling eye on the shackle pin and pass the running sling body through the shackle bow .
The Danger (Pin Roll-Out): If the running sling body is placed over the shackle pin, any movement, vibration, or settling of the load during the lift will cause the running line to rub against the pin. The rotational friction will unthread and back out the screw pin, causing the shackle to separate instantly and drop the load.