Study guide

6.3 Preliminary FF&E: Identifying Finish Materials

NCIDQ Interior Design Qualification Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the NCIDQ Exam 1.2 Eligibility & Application Routes 1.3 Test-Taking Strategies & Item Types 1.4 The 2026 NCIDQ Blueprint Overview

2 Study Planning, Codes & Logistics

2.1 Building a Study Plan 2.2 Codes & Reference Standards Overview 2.3 Fees, Schedule & Logistics

3 IDFX: Existing Conditions

3.1 Existing Conditions: Initial Code Analysis 3.2 Existing Conditions: Evaluating the Building

4 IDFX: Pre-Design

4.1 Pre-Design: Site Analysis 4.2 Pre-Design: Best Practices of Design 4.3 Pre-Design: Project Research & Development 4.4 Pre-Design: Determining Design Intent

5 IDFX: Programming

5.1 Programming: Validating the Project Program 5.2 Programming: Programmatic Diagrams 5.3 Programming: Determining User Needs

6 IDFX: Space Planning & Preliminary FF&E

6.1 Space Planning: Completing Space Plans 6.2 Space Planning: Creating Initial Drawings 6.3 Preliminary FF&E: Identifying Finish Materials 6.4 Preliminary FF&E: Identifying Significant FF&E

7 IDFX: Schematics

7.1 Schematics: Refining Design Intent 7.2 Schematics: Performing Code Review 7.3 Schematics: Visualizing Design

8 IDIX: Codes & Life Safety

8.1 Codes & Life Safety: Performing Code Review 8.2 Codes & Life Safety: Life Safety & Occupancy Plan

9 IDIX: Integration & FF&E

9.1 Integration: Integrating Equipment & Building Systems 9.2 Integration: Developing Finish Plan & Specifications 9.3 Integration: Developing Furniture Plans & Specifications

10 IDIX: Construction Documents

10.1 Construction Documents: Details & Sections 10.2 Construction Documents: Elevations 10.3 Construction Documents: Demolition Plans 10.4 Construction Documents: Construction Plans

11 IDIX: RCP & Consultant Coordination

11.1 Construction Documents: Reflected Ceiling Plans 11.2 Consultant Coordination: Coordinating Consultant Drawings & Specs 11.3 Consultant Coordination: Power, Data & Communication Plans 11.4 Consultant Coordination: Signage & Wayfinding

12 IDIX: Construction Specifications & Schedules

12.1 Construction Specifications & Schedules: Developing Construction Specifications 12.2 Construction Specifications & Schedules: Developing Schedules

13 IDPX: Feasibility Studies

13.1 Feasibility Studies: Identifying Project Stakeholders 13.2 Feasibility Studies: Managing the Project Team 13.3 Feasibility Studies: Evaluating Project Feasibility & Due Diligence

14 IDPX: Scheduling, Budgeting & Contracts

14.1 Scheduling & Budgeting: Managing the Project Schedule 14.2 Scheduling & Budgeting: Managing the Project Budget 14.3 Contracts & Procurement: Facilitating the Procurement/Bid Process 14.4 Contracts & Procurement: Managing Proposals & Contracts

15 IDPX: Approvals, Permitting & Construction Process

15.1 Approvals & Permitting: Obtaining Project Approvals 15.2 Approvals & Permitting: Participating in the Permit Process 15.3 Construction Process: Facilitating the Construction Process 15.4 Construction Process: Participating in Change Management

16 IDPX: Site Observation & Project Close-Out

16.1 Project Closeout & Evaluation: Performing Site Visits 16.2 Project Closeout & Evaluation: Conducting Project Close-Out

17 Final Review: Synthesizing the NCIDQ & Exam-Day Readiness

17.1 Synthesizing the Three Sections 17.2 Common Pitfalls & High-Yield Topics 17.3 Exam-Day Readiness & Final-Week Plan

6.3 Preliminary FF&E: Identifying Finish Materials

Key Takeaways Explain This Topic AI

ASTM E84 (Steiner Tunnel) classifies interior finishes as Class A (FSI 0–25), Class B (26–75), or Class C (76–200); all classes cap the smoke-developed index at 450, and both values must be met.

Sustainability certifications include GREENGUARD (low chemical emissions), FloorScore (hard-surface flooring), and SCS Indoor Advantage; VOC limits are governed by CARB, EPA TSCA Title VI, and LEED credits.

ADA Standards require floor surfaces to be stable, firm, and slip resistant — the 0.6 coefficient of friction figure is advisory, not a mandatory threshold.

Finish selection balances aesthetics, performance, sustainability, budget, lead time, and code compliance; no single criterion determines the choice.

Last updated: August 2026

Finish Selection: A Multi-Criteria Decision

Every finish selection is a compromise among competing criteria. The designer must satisfy code (will it pass plan review?), performance (will it wear?), sustainability (does it off-gas?), aesthetics (does it support the design concept?), budget (can the client afford it?), and lead time (will it arrive before move-in?). No single criterion wins — the designer weighs all six for every specification.

  • Code and Performance Standards
  • Flame Spread: ASTM E84

The ASTM E84 Steiner Tunnel test is the primary U.S. standard for interior finish fire performance. It measures two values: the flame spread index (FSI) — how fast flame travels across the surface — and the smoke-developed index (SDI) — total smoke released. Under IBC §803.1.2, materials are classified:

  • Class Flame Spread Index Smoke-Developed Index Typical Materials
  • A 0–25 0–450 Gypsum board, stone, tile, mineral fiber
  • B 26–75 0–450 Treated wood, some acoustic panels
  • C 76–200 0–450 Certain carpets, wood paneling

Critical rule: both FSI and SDI must be within range. A material with FSI 20 (Class A range) but SDI 500 fails Class A. Designers must verify both values on the test report.

Where Each Class Is Required

IBC Table 803.13 sets the required class by occupancy group and location (exit, corridor, room), with separate columns for sprinklered and non-sprinklered buildings. For example, a non-sprinklered Group B corridor requires Class B ; a non-sprinklered Group B room requires only Class C. Sprinkler protection generally allows a one-class reduction — but not for Group I-3 (detention) corridors or Group H (hazardous) corridors.

Slip Resistance

The ADA Standards (Section 302.1) require accessible floor surfaces to be stable, firm, and slip resistant . The standard does not mandate a specific coefficient of friction — the often-cited 0.6 value for level surfaces (and 0.8 for ramps) comes from advisory material in the ADAAG appendix, not the enforceable standard. Compliance is achieved by specifying surfaces that minimize slipperiness under expected conditions. Areas likely to be wet — entrances, restrooms, kitchens — should have a higher level of slip resistance.

  • Other Floor Surface Requirements (ADA §302)
  • Carpet : maximum pile height 1/2 inch, firm backing, securely attached

Openings (gratings) : no opening that allows passage of a 1/2-inch sphere; elongated openings oriented perpendicular to travel direction

Level changes : up to 1/4 inch vertical permitted; 1/4 to 1/2 inch must be beveled (slope no steeper than 1:2); over 1/2 inch requires a ramp

Sustainability Certifications

Interior finishes can emit volatile organic compounds (VOCs) and other pollutants after installation. Several third-party certifications verify low emissions:

  • Certification Scope Key Criteria
  • GREENGUARD Gold Broad product categories Stricter emissions limits; sensitive-occupancy (schools, healthcare)
  • GREENGUARD (standard) Broad product categories Low chemical emissions, 350+ VOCs tested
  • FloorScore Hard-surface flooring Meets CARB and CHPS requirements; SCS-certified
  • SCS Indoor Advantage Gold Furniture and finishes Meets CA 01350 for indoor air quality
  • Cradle to Cradle Material lifecycle Material health, recyclability, renewable energy
  • VOC Regulatory Limits

CARB (California Air Resources Board) sets the strictest U.S. VOC limits for paints, adhesives, sealants — widely adopted as de facto national standards

EPA TSCA Title VI (effective 2018) limits formaldehyde emissions from composite wood products (particleboard, MDF, plywood)

  • LEED v4.1 EQ Credit awards points for low-emitting materials meeting CA 01350 or GREENGUARD thresholds
  • Material Applications: Where Each Material Is Appropriate

Material Best Applications Performance Notes

Porcelain tile Restrooms, entries, kitchens High durability, slip-resistant textures available; cold/hard underfoot

Luxury vinyl tile (LVT) Offices, corridors, classrooms Durable, quieter than tile; check FloorScore certification

  • Broadloom carpet Offices, conference rooms Acoustic absorption; must meet Class A or B per occupancy
  • Carpet tile Open offices, retail Replaceable panels; check ASTM E84 class
  • Paint (latex) Walls, ceilings Low-VOC formulations widely available; CARB-compliant
  • Acoustic wall panels Offices, classrooms, auditoriums Must meet required flame-spread class; NRC ratings vary
  • Solid surface Countertops, reception desks Non-porous, seamless joints; Class A by default
  • Wood veneer Accent walls, millwork Must be treated or backed to meet required class; check FSI
  • Gypsum board (GWB) Walls, ceilings Class A by default; the baseline interior finish
  • Color Theory in Finish Selection

Color communicates brand, defines space, affects mood, and influences perceived scale. Key principles:

Hue, value, and chroma are the three dimensions of color. Value (lightness) has the strongest spatial effect — light colors make spaces feel larger; dark colors compress them.

Color temperature (warm vs. cool) affects perceived comfort. Warm tones benefit north-facing rooms that lack direct sunlight; cool tones suit hot, south-facing spaces.

Contrast for accessibility: ADA and A117.1 recommend light-on-dark contrast for elements like door frames, signage, and transitions to assist low-vision users. A contrast ratio of at least 70 percent is commonly cited.

Metamerism : two finishes that match under one light source may not match under another. Always evaluate samples under the project's specified lighting.

Budget and Lead Time

Finish selection must respect the project budget and schedule . A material that is perfect aesthetically but costs three times the allowance or has a 16-week lead time will delay occupancy. Designers should:

  • Verify stock availability before specifying custom or imported materials
  • Build alternates into the specification so the contractor can substitute if the first choice is unavailable

Track lead times from the start — a 12-week lead time means the order must be placed 12 weeks before installation

Balance first cost against life-cycle cost — a higher first cost may be justified by lower maintenance or longer service life

Sourcing and Reference Standards

Materials are sourced through manufacturers' representatives , showrooms , distributors , and direct from manufacturers. The designer should maintain a finish library with physical samples and current technical data sheets. Key reference standards to verify on every specification:

  • ASTM E84 — flame spread and smoke developed
  • ASTM D2394 — carpet wear testing
  • ASTM C627 — ceramic tile installation (Robinson test)
  • ANSI A138.1 — sustainable flooring (Tile Council)
  • ISO 14001 — environmental management system (manufacturer-level)

ASTM E84 Flame Spread Index Ranges by Class (Upper Limit)