Study guide
10.1 Construction Documents: Details & Sections
NCIDQ Interior Design Qualification Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NCIDQ Exam 1.2 Eligibility & Application Routes 1.3 Test-Taking Strategies & Item Types 1.4 The 2026 NCIDQ Blueprint Overview
2 Study Planning, Codes & Logistics
2.1 Building a Study Plan 2.2 Codes & Reference Standards Overview 2.3 Fees, Schedule & Logistics
3 IDFX: Existing Conditions
3.1 Existing Conditions: Initial Code Analysis 3.2 Existing Conditions: Evaluating the Building
4 IDFX: Pre-Design
4.1 Pre-Design: Site Analysis 4.2 Pre-Design: Best Practices of Design 4.3 Pre-Design: Project Research & Development 4.4 Pre-Design: Determining Design Intent
5 IDFX: Programming
5.1 Programming: Validating the Project Program 5.2 Programming: Programmatic Diagrams 5.3 Programming: Determining User Needs
6 IDFX: Space Planning & Preliminary FF&E
6.1 Space Planning: Completing Space Plans 6.2 Space Planning: Creating Initial Drawings 6.3 Preliminary FF&E: Identifying Finish Materials 6.4 Preliminary FF&E: Identifying Significant FF&E
7 IDFX: Schematics
7.1 Schematics: Refining Design Intent 7.2 Schematics: Performing Code Review 7.3 Schematics: Visualizing Design
8 IDIX: Codes & Life Safety
8.1 Codes & Life Safety: Performing Code Review 8.2 Codes & Life Safety: Life Safety & Occupancy Plan
9 IDIX: Integration & FF&E
9.1 Integration: Integrating Equipment & Building Systems 9.2 Integration: Developing Finish Plan & Specifications 9.3 Integration: Developing Furniture Plans & Specifications
10 IDIX: Construction Documents
10.1 Construction Documents: Details & Sections 10.2 Construction Documents: Elevations 10.3 Construction Documents: Demolition Plans 10.4 Construction Documents: Construction Plans
11 IDIX: RCP & Consultant Coordination
11.1 Construction Documents: Reflected Ceiling Plans 11.2 Consultant Coordination: Coordinating Consultant Drawings & Specs 11.3 Consultant Coordination: Power, Data & Communication Plans 11.4 Consultant Coordination: Signage & Wayfinding
12 IDIX: Construction Specifications & Schedules
12.1 Construction Specifications & Schedules: Developing Construction Specifications 12.2 Construction Specifications & Schedules: Developing Schedules
13 IDPX: Feasibility Studies
13.1 Feasibility Studies: Identifying Project Stakeholders 13.2 Feasibility Studies: Managing the Project Team 13.3 Feasibility Studies: Evaluating Project Feasibility & Due Diligence
14 IDPX: Scheduling, Budgeting & Contracts
14.1 Scheduling & Budgeting: Managing the Project Schedule 14.2 Scheduling & Budgeting: Managing the Project Budget 14.3 Contracts & Procurement: Facilitating the Procurement/Bid Process 14.4 Contracts & Procurement: Managing Proposals & Contracts
15 IDPX: Approvals, Permitting & Construction Process
15.1 Approvals & Permitting: Obtaining Project Approvals 15.2 Approvals & Permitting: Participating in the Permit Process 15.3 Construction Process: Facilitating the Construction Process 15.4 Construction Process: Participating in Change Management
16 IDPX: Site Observation & Project Close-Out
16.1 Project Closeout & Evaluation: Performing Site Visits 16.2 Project Closeout & Evaluation: Conducting Project Close-Out
17 Final Review: Synthesizing the NCIDQ & Exam-Day Readiness
17.1 Synthesizing the Three Sections 17.2 Common Pitfalls & High-Yield Topics 17.3 Exam-Day Readiness & Final-Week Plan
10.1 Construction Documents: Details & Sections
Key Takeaways Explain This Topic AI
Construction details and sections reveal internal assembly — how materials layer, where fasteners occur, and how fire ratings are maintained — making them the designer's primary tool for preventing RFIs and change orders.
A 1-hour rated partition typically uses 5/8" Type X gypsum on both sides of 2-1/2" metal studs at 16" o.c.; all penetrations must be sealed with listed firestopping to maintain the rating.
Standard millwork joinery includes the dado (groove across grain), rabbet (edge recess), and mortise-and-tenon (interlocking projection and slot); each serves a specific structural purpose in cabinetry.
Substrate selection is application-driven: plywood for casework, MDF for painted panels, cement board for wet areas, and particleboard for laminate-countertop cores.
Graphic hatching conventions (diagonal lines for gypsum, grain lines for wood, stippled dots for concrete) must be consistent across the sheet and defined in the legend.
Last updated: August 2026
Why Construction Details Matter
Construction details and sections are the designer's primary communication tool for conveying how building elements are assembled. While plans show horizontal relationships and elevations show vertical surfaces, sections and details reveal the internal construction — how materials layer, where fasteners occur, how transitions are made, and how fire-rated assemblies maintain their rating. On the IDIX exam, Domain III (Construction Documents) is the largest domain at 32 percent of the test, and details are where much of that content lives. A well-drawn detail prevents RFIs, reduces change orders, and ensures the built result matches the design intent.
Wall Types and Fire-Rated Assemblies
Interior partitions are classified by fire rating and acoustical performance (STC) . The designer selects assemblies from referenced standards — typically the Gypsum Association GA-600 Fire Resistance and Sound Control Design Manual or the UL Fire Resistance Directory — and keys them on a wall-type schedule. Common wall types:
Wall Type Assembly Fire Rating STC Typical Use
Type A 5/8" Type X gyp, both sides; 2-1/2" metal studs, 16" o.c. 1 hr 40-43 Corridor partitions, tenant separation
- Type B Double 5/8" Type X gyp, both sides; 3-5/8" metal studs 2 hr 45-50 Exit enclosures, stair shafts
- Type C 1/2" gyp, both sides; 2-1/2" metal studs Non-rated 33-35 General office partitions
- Type D CH-stud shaft wall; 1" gyp liner, 2-1/2" studs 1-2 hr 40-45 Area separation, shaft walls
- Type E 5/8" Type X + sound batt; resilient channel 1 hr 50+ Acoustically sensitive rooms
A 1-hour rated partition (Type A) uses 5/8" Type X gypsum board on both sides of 2-1/2" metal studs at 16" o.c. The fire rating depends on the Type X core, which contains glass fibers and vermiculite that resist heat transfer and maintain structural integrity longer than regular board. Penetrations through rated walls — electrical boxes, ducts, pipes — must be sealed with firestopping (intumescent putty, fire caulk, or mineral wool) listed for the specific assembly. Electrical boxes on opposite sides of the same stud cavity must be separated by a minimum horizontal distance (typically 24" per GA-600) to avoid compromising the rating.
Millwork Joinery
Custom millwork details show how cabinetry is constructed. The IDIX exam tests knowledge of standard woodworking joints :
Dado : a rectangular groove cut across the grain of one board to receive the end of another; used for shelving into side panels.
Rabbet : a recess cut along the edge of a board; used for joining cabinet backs to sides or for door insets.
Mortise-and-tenon : a projecting tenon on one piece fits into a mortise (slot) on another; used for face frames and door construction for maximum strength and durability.
Dowel : cylindrical wood pins joining two boards; an alternative to mortise-and-tenon for hidden joints.
Biscuit : compressed wood wafers inserted into matched slots; used for alignment in panel joints.
The detail drawing shows the joint type, dimensions, and finish. Plywood is the standard substrate for casework; veneer or laminate finishes are applied over the plywood core.
Typical STC Ratings by Partition Assembly
Substrates
The detail must specify the correct substrate for each application:
- Substrate Properties Typical Application
- Plywood Cross-grain veneers; strong, stable Casework, wall paneling, shelving
- MDF Fine fibers, smooth surface, no grain Painted panels, profiled trim, doors
- Particleboard Coarse chips, cost-effective Countertop substrate under laminate
- Gypsum board Fire-resistant, noncombustible Wall substrate for tile, paneling
- Cement board Moisture-resistant, dimensionally stable Wet areas, tile substrate
MDF sands smoother than plywood but does not hold fasteners as well and swells if exposed to moisture. Cement board is required in continuously wet areas (showers, tub surrounds) as a tile substrate because it does not deteriorate with moisture, whereas gypsum board will degrade behind tile in wet conditions.
Material Transitions
Details must show how different materials meet — at the ceiling, floor, and wall :
Ceiling transitions : where a suspended acoustical ceiling meets a gypsum-board soffit or perimeter; the detail shows the wall angle, support, and edge trim.
Floor transitions : where tile meets carpet, or LVT meets concrete; the detail shows the transition strip, height adjustment, and adhesive or thin-set method.
Wall transitions : where wainscot meets wall finish above, or where tile terminates; the detail shows the cap profile, sealant, and substrate.
Each transition must address tolerances — the acceptable dimensional variation between materials. A tile floor installed over a slab may vary ±1/4" in flatness; the transition detail must accommodate this without creating a trip hazard.
Graphic Standards for Materials
Construction drawings use standard hatching and poche conventions to identify materials in section:
- Material Hatch Pattern
- Gypsum board Diagonal lines, widely spaced
- Wood (solid) Regular grain lines parallel to surface
- Plywood Alternating grain directions per ply
- Stone Random diagonal masonry pattern
- Metal Diagonal lines, closely spaced, often labeled "METAL"
- Concrete Random stippled dots with diagonal lines
- Insulation Zigzag or dotted pattern
These conventions are standardized but vary slightly by office. The key is consistency : the legend on each sheet must define what each hatch represents so the contractor and reviewer can read the drawing unambiguously.
Exam Scenario
A typical IDIX detail question shows a wall section and asks the candidate to identify the fire-rating deficiency. For example, a section shows a 1-hour rated corridor wall with an electrical box placed back-to-back with another box on the opposite side of the same stud cavity, without firestopping. The correct answer identifies that electrical boxes in rated walls must be separated by a minimum horizontal distance (typically 24" per GA-600) or sealed with listed firestopping to maintain the assembly rating.