Study guide
7.2 Commercial Garages, Motor Fuel Dispensing & Spray Areas (Articles 511, 514, 516)
Nebraska Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Nebraska State Electrical Act, Licensing & Exam Navigation
1.1 Nebraska Licensing Framework & State Electrical Act 1.2 Permitting, Inspections & Code Enforcement in Nebraska 1.3 Exam Format, NEC 2023 Structure & Open-Book Strategy
2 Chapter 2: General Electrical Knowledge — Definitions, Theory & Article 110
2.1 NEC Article 100 Definitions & Mandatory Code Rules 2.2 Electrical Theory, Ohm's Law & Power Calculations 2.3 General Installation Requirements & Equipment Working Spaces
3 Chapter 3: Branch Circuits, GFCI/AFCI, Load Calculations & Outside Feeders
3.1 Branch-Circuit Ratings & Required Outlets 3.2 GFCI & AFCI Protection Requirements 3.3 Feeder Sizing & General Demand Factors 3.4 Dwelling Unit Service & Feeder Load Calculations 3.5 Outside Branch Circuits, Feeders & Separate Buildings
4 Chapter 4: Services, Overcurrent Protection, Grounding & Bonding
4.1 Services & Service Equipment 4.2 Overcurrent Protection & Surge Protection (Articles 240 and 242) 4.3 Grounding vs. Bonding Principles 4.4 Grounding Electrode System & GEC Sizing 4.5 Equipment Grounding Conductors & Bonding Jumpers
5 Chapter 5: Wiring Methods, Conductors & Enclosure Calculations
5.1 Conductor Sizing, Ampacity & Derating 5.2 Raceways, Cable Assemblies & Underground Installations 5.3 Conduit Fill & Raceway Calculations 5.4 Box Fill & Enclosure Sizing
6 Chapter 6: Equipment for General Use
6.1 Receptacles, Switches & Luminaires 6.2 Cords, Panelboards, Appliances, Space Heating & Generators 6.3 Motor Branch Circuits, Overload & Short-Circuit Protection 6.4 Transformers & HVAC Equipment
7 Chapter 7: Special Occupancies
7.1 Hazardous (Classified) Locations 7.2 Commercial Garages, Motor Fuel Dispensing & Spray Areas (Articles 511, 514, 516) 7.3 Agricultural Buildings & Livestock Facilities 7.4 Healthcare Facilities & Places of Assembly 7.5 Manufactured Homes, RV Parks, Marinas & Temporary Installations (Articles 550, 551, 555, 590)
8 Chapter 8: Special Equipment — Pools, Solar PV, EV Charging & More
8.1 Swimming Pools, Spas & Hot Tubs (Article 680) 8.2 Solar Photovoltaic Systems & Energy Storage 8.3 EV Charging, Signs, Welders, Elevators & Fire Pumps (Articles 625, 600, 630, 620, 695)
9 Chapter 9: Special Conditions, Fire Alarm & Jobsite Safety
9.1 Emergency, Legally Required & Optional Standby Systems 9.2 Fire Alarm, Class 1, Class 2 & Class 3 Circuits (Articles 760, 722, 724, 725, 770) 9.3 Electrical Safety, OSHA & NFPA 70E Work Practices
7.2 Commercial Garages, Motor Fuel Dispensing & Spray Areas (Articles 511, 514, 516)
Key Takeaways Explain This Topic AI
Parking garages are unclassified; repair garages are classified by fuel type and ventilation under Tables 511.3(C) and 511.3(D).
Around a motor fuel dispenser, the area within 20 feet horizontally and up to 18 inches above grade is Class I, Division 2 (Table 514.3(B)(1)).
Fuel dispensing emergency disconnects must be located not less than 20 feet nor more than 100 feet from the dispensers they serve (NEC 514.11(A)).
Underground PVC at a fuel island needs 2 feet of cover and threaded metal conduit for the last 2 feet before it emerges (NEC 514.8).
A seal must be the first fitting after a conduit emerges from the earth or concrete into a dispenser (NEC 514.9).
Last updated: October 2026
Commercial Garages, Motor Fuel Dispensing & Spray Areas (Articles 511, 514, 516)
Articles 510 through 517 apply the hazardous-location rules of Articles 500–506 to specific occupancies. Each article tells you exactly where the classified areas begin and end, so you don't have to work out the classification yourself. Under 510.2 , the general rules of Chapters 1–4 and Articles 500–504 apply except as these articles modify them. In Nebraska, these rules show up in:
- dealership and farm-implement repair shops;
- truck stops and convenience-store fuel islands along I-80;
- cooperative fuel and propane depots; and
body shops with paint booths.
1. Commercial Garages, Repair and Storage (Article 511)
Parking garages are not classified. Garages used only for parking or storing vehicles are unclassified (511.3(A)).
Repair garages are classified by fuel type and ventilation. The two key definitions are:
a major repair garage works on engines, fuel systems, or bodies, and may drain fuel; and
a minor repair garage handles lubrication, inspection, tires, brakes, and similar work without draining fuel tanks.
The classification tables are:
Table 511.3(C): vehicles using heavier-than-air fuels such as gasoline, diesel, and propane. The hazard collects at the floor and in pits.
Table 511.3(D): vehicles using lighter-than-air fuels such as natural gas (CNG) and hydrogen. The hazard collects at the ceiling.
Area (heavier-than-air fuels) Typical classification
Pit, below-grade work area, or subfloor work area, not ventilated , in a major repair garage Class I, Division 1 , entire space
The same space in a minor repair garage Class I, Division 2
Floor-level area up to 18 inches above the floor, where required by the table and not removed by ventilation Class I, Division 2
Adequately ventilated areas meeting the table's air-change requirements Reduced or unclassified, per the table
Read the table for the exact ventilation conditions and distances. They are the most-tested details in Article 511.
Wiring and equipment:
Above classified areas (511.7): Fixed wiring above a classified location must be in metal raceways, PVC, ENT, MI, MC, or other approved methods.
Sparking equipment: Equipment less than 12 feet above the floor that may produce arcs or sparks must be totally enclosed or built to prevent the escape of sparks.
Lighting over lanes: Fixed lighting over lanes where vehicles are commonly driven must be at least 12 feet above the floor unless it is totally enclosed.
Pendants and cords (511.7): Pendants and cords must be suitable for the location and hung so they do not reach into the classified area unless identified for it.
Sealing (511.9): Seals follow 501.15 . Classified-area boundaries need seals just as in Article 501.
GFCI: Service bays and similar garage areas are GFCI locations under 210.8(B) , which covers 125-volt through 250-volt receptacles on single-phase circuits of 150 volts or less to ground and 50 A or less.
Battery chargers and their control equipment may not be installed in classified locations.
- 2. Motor Fuel Dispensing Facilities (Article 514)
- Classified areas (Table 514.3(B)(1))
- Location Classification
- Inside the dispenser enclosure Class I, Division 1
Within 20 ft horizontally of the dispenser enclosure, from grade up to 18 inches above grade Class I, Division 2
- Pits, boxes, or spaces below grade , any part of which lies within a Division 1 or 2 area Class I, Division 1
- Underground tank fill openings, vents, and similar points Classified per the table's radii
- Underground wiring (514.8)
Underground wiring must be in threaded RMC or threaded steel IMC .
PVC or RTRC is permitted where buried under at least 2 feet of cover . The last 2 feet of the run to the point of emergence, or to the connection with an aboveground raceway, must be threaded RMC or threaded steel IMC, and an EGC must be included.
Any portion of wiring below the surface of a Division 1 or 2 area must be sealed within 10 feet of the point of emergence above grade.
Sealing (514.9)
A seal is required in each conduit run entering or leaving a dispenser , or any cavity or enclosure in direct communication with it. The seal fitting, or a listed explosionproof reducer at the seal, must be the first fitting after the conduit emerges from the earth or concrete.
Emergency electrical disconnects (514.11(A))
Fuel dispensing systems need one or more clearly identified emergency shutoff devices or electrical disconnects :
installed in approved locations not less than 20 feet nor more than 100 feet from the dispensers they serve;
disconnecting power to all dispensing devices, all remote pumps, all associated power, control, and signal circuits, and all other electrical equipment in the classified areas around the dispensers; and
requiring manual reset after operation, in a manner approved by the authority having jurisdiction.
At attended self-service stations, the devices must be readily accessible to the attendant. At unattended self-service stations, additional emergency controls are required at each group of dispensers or at the outdoor equipment that controls them.
Maintenance disconnect (514.13)
Each dispensing device must have a means to remove all external voltage sources during maintenance and service, including power, communications, data, and video circuits, and including feedback . The means may be located away from the dispenser, but it must be capable of being locked in the open position (110.25).
3. Spray Application, Dipping, Coating & Printing (Article 516)
Body-shop paint booths and industrial finishing rooms fall under Article 516.
Inside spray booths, spray rooms, and exhaust ducts: Classified Division 1 (or Zone 1 for vapors and Zone 21 for powders).
Areas around booth openings: Division 2 (or Zone 2) to the distances shown in the article's figures.
Lighting: Booth lighting is commonly installed outside the booth, shining through sealed, noncombustible panels so lamps are outside the classified space.
Interlocks: NFPA 33, the spray-application standard that Article 516 works with, requires spray equipment to be interlocked with the booth's exhaust ventilation, so spraying cannot occur unless the fans are running.
Electrostatic equipment: Electrostatic spraying and detearing equipment has its own rules for grounding of objects being coated and for spacing.
Equipment next to booths: Electrical equipment above or next to a spray area that is not separated by a tight partition must not be able to release sparks or hot metal particles. It must be totally enclosed or constructed to prevent their escape.
4. Applying Articles 500–504 Inside These Spaces
Once a space is classified, the Article 501 (Class I) rules apply, as covered in section 7.1:
- threaded RMC or IMC in Division 1;
- explosionproof enclosures with five full threads engaged;
- seals within 18 inches of arcing enclosures; and
boundary seals within 10 feet.
The occupancy articles change only where the boundaries are and add occupancy-specific rules such as the 514.11 emergency disconnect.
5. Common Exam Traps
Dispenser Division 2 radius: The Division 2 area is 20 feet horizontally and 18 inches high. It is not 20 feet high.
Emergency disconnect distance: The device must be at least 20 feet and no more than 100 feet from the dispensers.
Maintenance disconnect: It must remove all external voltage sources, including data and communications circuits and feedback, and it must be lockable.
Underground PVC at a fuel island: PVC needs 2 feet of cover, plus 2 feet of threaded metal conduit before emergence.
Parking garages: They are unclassified. Only repair garages are classified.