Study guide

10.2 Expansion Tanks, Point of No Pressure Change, and Fill Pressure

NEBB Testing, Adjusting and Balancing Certified Technician CT

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Role, Documents, and Readiness

1.1 NEBB TAB CT Role, CP Guidance, Standards, and Data Integrity 1.2 Interpreting Plans, Schedules, and Control Sequences 1.3 Field Verification, Pre-TAB Readiness, and Deficiencies

2 Chapter 2: TAB Math and Heat Transfer

2.1 TAB Mathematics, Units, Ratios, and Formula Discipline 2.2 Air-Side Sensible, Latent, and Total Heat Transfer 2.3 Hydronic Heat Transfer, Glycol Corrections, and Coil Cross-Checks

3 Chapter 3: Psychrometrics

3.1 Psychrometric Properties and Reading the Chart 3.2 Psychrometric Processes, Air Mixing, and Coil Diagnostics

4 Chapter 4: TAB Instrumentation and Measurement Quality

4.1 Pressure Instruments, Manometers, Zeroing, and Tubing 4.2 Airflow Instruments: Hoods, Anemometers, and Pitot Tubes 4.3 Hydronic Pressure and Temperature Instruments 4.4 Electrical and Rotational Instruments

5 Chapter 5: Air Systems and Airflow Fundamentals

5.1 Air-System Configurations and System Relationships 5.2 Airflow Continuity, Standard Air, Density, and Velocity 5.3 Duct Geometry and Worked Airflow Calculations

6 Chapter 6: Duct Traverses

6.1 Traverse Locations, Disturbances, and Point Layout 6.2 Traverse Velocity Conversion and Airflow Calculation

7 Chapter 7: Terminal Measurements and Air Balancing

7.1 Terminal Devices, Effective Area, and Capture-Hood Checks 7.2 Proportional Air Balancing and Final Verification 7.3 Outside Air, Exhaust Balancing, and Building Pressurization

8 Chapter 8: Fans, Motors, and Drives

8.1 Fan Types, Performance Curves, and Rotation 8.2 Fan Affinity Laws, Pressure, and Power 8.3 Motors, Single- and Three-Phase Measurements, and Loading 8.4 Belts, Sheaves, Alignment, and Variable Frequency Drives

9 Chapter 9: HVAC Controls and VAV Systems

9.1 HVAC Control Fundamentals, Signals, and Test States 9.2 VAV Terminal Types, Airflow Sensors, and Calibration 9.3 VAV System Balancing, Diversity, and Static-Pressure Control

10 Chapter 10: Hydronic System Fundamentals

10.1 Hydronic Pressure, Head, Open and Closed Systems, and Resistance 10.2 Expansion Tanks, Point of No Pressure Change, and Fill Pressure

11 Chapter 11: Pumps and Hydronic Balancing

11.1 Centrifugal Pumps, Pump Curves, and Pump Affinity Laws 11.2 Balancing Valves, Circuit Setters, Strainers, and Hydronic Procedures

12 Chapter 12: Reporting, Safety, and Problem Solving

12.1 Project Acceptance Criteria, Data Traceability, and Certified Reports 12.2 Field Safety, Electrical Boundaries, Pressure, and Access 12.3 Integrated TAB Problem Solving and Measurement Cross-Checks

10.2 Expansion Tanks, Point of No Pressure Change, and Fill Pressure

Key Takeaways Explain This Topic AI

The expansion-tank connection establishes the point of no pressure change for the circulating pump's dynamic pressure profile.

A common pumping-away arrangement places the tank connection near pump suction so pump head is added downstream, but actual pressure must still be measured.

Cold fill pressure accounts for elevation, fluid specific gravity, and the project-required residual pressure at the high point; five psi is an example input, not a universal addition.

Tank precharge checks and fill adjustments follow manufacturer instructions, design limits, safe isolation, and the authorized project procedure.

Last updated: August 2026

  • Hydronic System Pressure, Expansion Tanks, and Fill
  • Static pressure and elevation

A water column creates approximately 1 psi for each 2.31 feet of elevation. In a closed system at rest, pressure decreases with height and increases with depth. The required cold fill pressure at the makeup or expansion-tank connection is therefore:

fill pressure = elevation difference / 2.31 + required residual pressure at the high point

The residual is a design value, not a universal five-psi NEBB rule. It must support air management and equipment requirements while remaining compatible with relief-valve settings, component ratings, operating temperature, and expansion-tank acceptance volume.

Example: the highest piping is 74 feet above the fill connection and the project design requires 5 psi residual there. The elevation term is 74 / 2.31 = 32.0 psi, so the calculated fill value is about 37.0 psig. This answer follows the stated design residual; a different project residual changes the result.

Point of no pressure change

The expansion-tank connection is commonly described as the point of no pressure change because pump operation does not materially change pressure at that connection. Pump head is added on one side and subtracted on the other relative to that reference. In a common pumping-away arrangement, the pump discharge sees the added dynamic head, helping maintain positive pressure margin through the distribution system.

Do not turn that common arrangement into a universal diagnosis. Pump location, tank connection, fill point, system height, temperature, and resistance all determine the pressure profile. Pumping toward a tank does not by itself prove that the suction is sub-atmospheric or that cavitation must occur.

Expansion-tank checks

Identify tank type, volume, location, connection, design precharge, cold fill value, and relief setting from approved documents and manufacturer data. For a bladder or diaphragm tank, precharge is checked only with the water side isolated and pressure relieved as required by the manufacturer. Reading air-side pressure against a pressurized water system does not reveal the true precharge.

An undersized, waterlogged, isolated, or incorrectly charged tank can cause a large pressure rise as the fluid heats and can lead to relief discharge. An excessive or incorrect fill setting can also reduce available expansion volume. A low cold pressure may allow high-point air entry or poor pump suction margin. The symptom must be traced rather than corrected by adding water blindly.

Field verification

Check the pressure profile in order:

  • identify the approved fill, residual, relief, and tank values;
  • record cold static pressure, temperature, and gauge elevation;
  • compare readings at a common elevation;
  • observe pump suction and discharge under the defined mode; and

escalate any unsafe or unexplained pressure condition.

Record cold static pressure at a known elevation, system temperature, tank condition, makeup setting, and high-point or other comparison pressure if safe access exists. Correct readings to a common elevation before comparing them. Under pump operation, measure suction and discharge pressure simultaneously and calculate differential head using fluid specific gravity.

Never isolate an operating system from its only expansion path, defeat a relief valve, or add pressure beyond the approved design. Tank service and fill adjustments require authorization and may belong to another trade. The CT documents the pressure profile, abnormal cycling or discharge, and its effect on valid hydronic testing, then obtains direction from the CP.

Worked pressure-profile check

Assume a cold static gauge at the tank connection reads 36 psig and another gauge 46.2 feet higher reads 16 psig. The expected elevation difference for water is about 46.2/2.31 = 20 psi, so the two readings are mutually consistent before gauge uncertainty. If the upper gauge instead reads near zero, investigate gauge accuracy, trapped air, isolation, fill state, and actual elevations before changing the pressure reducing valve.

During pump operation, do not confuse dynamic differential with static fill. The pump redistributes pressure around the loop relative to the tank connection; it does not create the cold static elevation requirement. Compare cold and running readings only with temperatures, valve states, and gauge locations recorded.

For hot-water systems, thermal expansion raises pressure as temperature rises. The acceptable cold-to-hot change depends on tank sizing, precharge, fill, relief setting, and fluid expansion. A relief discharge is a symptom requiring authorized diagnosis, not permission to alter a safety device.

A final pressure record should also identify the gauge datum and the fluid specific gravity. Without those references, a correct number cannot be compared reliably with a high-point requirement or another instrument location.