Study guide

2.3 Hydronic Heat Transfer, Glycol Corrections, and Coil Cross-Checks

NEBB Testing, Adjusting and Balancing Certified Technician CT

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Role, Documents, and Readiness

1.1 NEBB TAB CT Role, CP Guidance, Standards, and Data Integrity 1.2 Interpreting Plans, Schedules, and Control Sequences 1.3 Field Verification, Pre-TAB Readiness, and Deficiencies

2 Chapter 2: TAB Math and Heat Transfer

2.1 TAB Mathematics, Units, Ratios, and Formula Discipline 2.2 Air-Side Sensible, Latent, and Total Heat Transfer 2.3 Hydronic Heat Transfer, Glycol Corrections, and Coil Cross-Checks

3 Chapter 3: Psychrometrics

3.1 Psychrometric Properties and Reading the Chart 3.2 Psychrometric Processes, Air Mixing, and Coil Diagnostics

4 Chapter 4: TAB Instrumentation and Measurement Quality

4.1 Pressure Instruments, Manometers, Zeroing, and Tubing 4.2 Airflow Instruments: Hoods, Anemometers, and Pitot Tubes 4.3 Hydronic Pressure and Temperature Instruments 4.4 Electrical and Rotational Instruments

5 Chapter 5: Air Systems and Airflow Fundamentals

5.1 Air-System Configurations and System Relationships 5.2 Airflow Continuity, Standard Air, Density, and Velocity 5.3 Duct Geometry and Worked Airflow Calculations

6 Chapter 6: Duct Traverses

6.1 Traverse Locations, Disturbances, and Point Layout 6.2 Traverse Velocity Conversion and Airflow Calculation

7 Chapter 7: Terminal Measurements and Air Balancing

7.1 Terminal Devices, Effective Area, and Capture-Hood Checks 7.2 Proportional Air Balancing and Final Verification 7.3 Outside Air, Exhaust Balancing, and Building Pressurization

8 Chapter 8: Fans, Motors, and Drives

8.1 Fan Types, Performance Curves, and Rotation 8.2 Fan Affinity Laws, Pressure, and Power 8.3 Motors, Single- and Three-Phase Measurements, and Loading 8.4 Belts, Sheaves, Alignment, and Variable Frequency Drives

9 Chapter 9: HVAC Controls and VAV Systems

9.1 HVAC Control Fundamentals, Signals, and Test States 9.2 VAV Terminal Types, Airflow Sensors, and Calibration 9.3 VAV System Balancing, Diversity, and Static-Pressure Control

10 Chapter 10: Hydronic System Fundamentals

10.1 Hydronic Pressure, Head, Open and Closed Systems, and Resistance 10.2 Expansion Tanks, Point of No Pressure Change, and Fill Pressure

11 Chapter 11: Pumps and Hydronic Balancing

11.1 Centrifugal Pumps, Pump Curves, and Pump Affinity Laws 11.2 Balancing Valves, Circuit Setters, Strainers, and Hydronic Procedures

12 Chapter 12: Reporting, Safety, and Problem Solving

12.1 Project Acceptance Criteria, Data Traceability, and Certified Reports 12.2 Field Safety, Electrical Boundaries, Pressure, and Access 12.3 Integrated TAB Problem Solving and Measurement Cross-Checks

2.3 Hydronic Heat Transfer, Glycol Corrections, and Coil Cross-Checks

Key Takeaways Explain This Topic AI

Use Q = 500 × GPM × ΔT only when the rounded water-property assumption is appropriate.

For other fluids, use approved density and specific heat at a representative temperature; glycol type and concentration alone do not establish the factor.

Match flow and temperature measurement boundaries and collect stable, coordinated readings.

Air-side and water-side results are uncertainty-sensitive cross-checks, not automatic proof of a particular defect.

Last updated: August 2026

  • Hydronic Heat Transfer and Fluid Properties
  • Begin with mass and energy

A hydronic heat-transfer calculation estimates the energy carried by a measured liquid flow through a measured temperature change. The general relationship is:

Q = 60 × GPM × ρ × Cp × ΔT

Q is heat transfer in Btu/h, ρ is fluid density in pounds per gallon, Cp is specific heat in Btu/(lb·°F), and ΔT is the entering-to-leaving temperature change in degrees Fahrenheit. The factor 60 converts gallons per minute to gallons per hour.

For water near ordinary HVAC conditions, ρ is approximately 8.33 lb/gal and Cp approximately 1.0. Their product with 60 is about 500, giving the familiar shortcut:

Qwater = 500 × GPM × ΔT

This rounded relationship is useful when the specified fluid and required accuracy justify it. State whether the result is heating or cooling and keep the temperature sign convention consistent.

Example: a chilled-water coil transfers 300,000 Btu/h with a 12°F water rise. Assuming the water shortcut applies:

GPM = 300,000 / (500 × 12) = 50 GPM

The calculation does not independently prove the measured flow. Flow, temperature difference, and the selected property factor each contribute uncertainty.

Fluids other than water

A glycol solution cannot be handled by selecting a universal “glycol constant.” Property values depend on glycol type, concentration, temperature, inhibitor package, and condition. Identify the actual fluid and obtain density and specific heat from approved manufacturer data, a laboratory result, or another project-authorized source at a representative temperature.

If property data are expressed relative to the same water basis, the coefficient is often approximated as:

C ≈ 500 × SG × Cp

and then Q = C × GPM × ΔT . This form assumes the reference choices behind the factor 500 are appropriate. The more direct form, 60 × density in lb/gal × specific heat, avoids ambiguity.

For a stated example with SG = 1.050 and Cp = 0.880, C is:

500 × 1.050 × 0.880 = 462

That result belongs only to the stated properties. It must not be generalized into a typical range or inferred from concentration alone. Viscosity does not appear directly in the heat equation, but it affects pressure loss, pump performance, and the validity of some flow-device relationships.

Temperature measurement

A small temperature difference makes the percentage uncertainty in Q large. Verify sensor calibration, resolution, insertion depth, thermal contact, and representative location. Use matched probes where practical and collect entering and leaving readings at the same stable time. A surface probe needs a manufacturer-appropriate preparation and insulation method; no single cleaning material, paste, or distance from the coil is universal.

Confirm that the temperature stations bracket the same equipment as the flow measurement. A bypass connection, three-way valve, common pipe, mixing point, or active secondary loop between stations can invalidate the assumed boundary.

Do not force a nominal design ΔT onto field data. Low measured ΔT can result from excess flow, low load, control action, mixing, sensor error, or system interaction. High ΔT can result from low flow, high load, a restricted circuit, or a different operating mode. The temperature difference is evidence that must be interpreted with flow and control state.

Flow measurement and configuration

Record the flow method, instrument, device identity, valve position, fluid setting, pressure differential if applicable, pump speed, and piping lineup. A balance valve or flow station must use the applicable manufacturer relationship and fluid basis. A pump curve is not a substitute for a direct flow measurement unless the approved procedure supports that inference and the actual speed, impeller, fluid, and configuration are known.

Air, strainers, control valves, fouled coils, bypasses, and reversed flow can alter the measured condition. Restore temporary valve or control changes after the test and verify normal operation.

Air-side and water-side comparison

For a heating coil with negligible moisture change, an air-side sensible estimate can be compared with the hydronic estimate:

1.08 × CFM × ΔTair ≈ C × GPM × ΔTfluid

For example, 25 GPM of water with a 16°F drop carries about 200,000 Btu/h. If the air temperature rises 20°F and the standard-air assumption is valid, the corresponding airflow estimate is:

CFM = 200,000 / (1.08 × 20) ≈ 9,259 CFM

This is a cross-check, not an exact conservation test. Airflow, fluid flow, and four temperature readings all have uncertainty. Casing loss, fan heat, piping loss, leakage, storage, nonuniform air temperature, condensate, and mismatched timing can create legitimate differences. A mismatch does not by itself prove fouling, air binding, or bypass leakage.

A disciplined diagnostic sequence

When the two sides disagree, first verify arithmetic, units, signs, fluid properties, and whether the measurements describe the same stable boundary. Next examine instrument calibration, sensor placement, airflow stratification, flow-device configuration, and simultaneous timing. Only then use the direction of the discrepancy with pressure, valve, and control evidence to investigate a physical cause.

Document the measured state rather than back-solving a preferred answer. A reproducible record includes:

  • fluid identity, representative temperature, and property source;
  • entering and leaving temperatures with exact locations;
  • flow, instrument, device setting, and measurement method;
  • pump, valve, and control operating mode;
  • raw calculation, units, assumptions, and rounding; and

uncertainty, mismatch investigation, or unresolved limitation.