Study guide
5.3 Duct Geometry and Worked Airflow Calculations
NEBB Testing, Adjusting and Balancing Certified Technician CT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Role, Documents, and Readiness
1.1 NEBB TAB CT Role, CP Guidance, Standards, and Data Integrity 1.2 Interpreting Plans, Schedules, and Control Sequences 1.3 Field Verification, Pre-TAB Readiness, and Deficiencies
2 Chapter 2: TAB Math and Heat Transfer
2.1 TAB Mathematics, Units, Ratios, and Formula Discipline 2.2 Air-Side Sensible, Latent, and Total Heat Transfer 2.3 Hydronic Heat Transfer, Glycol Corrections, and Coil Cross-Checks
3 Chapter 3: Psychrometrics
3.1 Psychrometric Properties and Reading the Chart 3.2 Psychrometric Processes, Air Mixing, and Coil Diagnostics
4 Chapter 4: TAB Instrumentation and Measurement Quality
4.1 Pressure Instruments, Manometers, Zeroing, and Tubing 4.2 Airflow Instruments: Hoods, Anemometers, and Pitot Tubes 4.3 Hydronic Pressure and Temperature Instruments 4.4 Electrical and Rotational Instruments
5 Chapter 5: Air Systems and Airflow Fundamentals
5.1 Air-System Configurations and System Relationships 5.2 Airflow Continuity, Standard Air, Density, and Velocity 5.3 Duct Geometry and Worked Airflow Calculations
6 Chapter 6: Duct Traverses
6.1 Traverse Locations, Disturbances, and Point Layout 6.2 Traverse Velocity Conversion and Airflow Calculation
7 Chapter 7: Terminal Measurements and Air Balancing
7.1 Terminal Devices, Effective Area, and Capture-Hood Checks 7.2 Proportional Air Balancing and Final Verification 7.3 Outside Air, Exhaust Balancing, and Building Pressurization
8 Chapter 8: Fans, Motors, and Drives
8.1 Fan Types, Performance Curves, and Rotation 8.2 Fan Affinity Laws, Pressure, and Power 8.3 Motors, Single- and Three-Phase Measurements, and Loading 8.4 Belts, Sheaves, Alignment, and Variable Frequency Drives
9 Chapter 9: HVAC Controls and VAV Systems
9.1 HVAC Control Fundamentals, Signals, and Test States 9.2 VAV Terminal Types, Airflow Sensors, and Calibration 9.3 VAV System Balancing, Diversity, and Static-Pressure Control
10 Chapter 10: Hydronic System Fundamentals
10.1 Hydronic Pressure, Head, Open and Closed Systems, and Resistance 10.2 Expansion Tanks, Point of No Pressure Change, and Fill Pressure
11 Chapter 11: Pumps and Hydronic Balancing
11.1 Centrifugal Pumps, Pump Curves, and Pump Affinity Laws 11.2 Balancing Valves, Circuit Setters, Strainers, and Hydronic Procedures
12 Chapter 12: Reporting, Safety, and Problem Solving
12.1 Project Acceptance Criteria, Data Traceability, and Certified Reports 12.2 Field Safety, Electrical Boundaries, Pressure, and Access 12.3 Integrated TAB Problem Solving and Measurement Cross-Checks
5.3 Duct Geometry and Worked Airflow Calculations
Key Takeaways Explain This Topic AI
The volumetric airflow continuity equation Q = A × V (CFM = Area in sq ft × Velocity in FPM) is the fundamental governing law for fluid flow in HVAC distribution ducts.
Duct cross-sectional area calculations must always convert inch dimensions to square feet by dividing by 144, and internal acoustic duct liner thickness must be subtracted twice from external dimensions.
A calculation must use the internal flow dimensions at the measurement plane, accounting for liner or obstructions when applicable.
Worked results should be checked against duct size, measured pressure, design flow, and instrument range before reporting.
Last updated: August 2026
Duct Geometry and Worked Airflow Calculations
A traverse produces velocity at a defined plane; converting it to airflow requires the net internal area at that same plane . Record whether dimensions came from a drawing, label, or field measurement and whether they are outside or clear inside dimensions.
5. Duct Geometric Calculations and Net Internal Area
To compute total volumetric flow ( Q = A × V Q = A \times V Q = A × V ), technicians must calculate the precise net cross-sectional area of ductwork. External dimensions must be adjusted for internal insulation (acoustic liner). Rectangular Duct Round Spiral Duct Flat Oval Duct
+------------------+ .--------. .--------------.
- | |============| | / /======\ \ / /==========\ \
- | | Net H | | | | Net D | | ( ( Net a Net A ) )
- | |============| | \ \======/ / \ \==========/ /
- +------------------+ '--------' '--------------'
- Net W
1. Rectangular Ducts A (sq ft) = W (in.) × H (in.) 144 A\text{ (sq ft)} = \frac{W\text{ (in.)} \times H\text{ (in.)}}{144} A (sq ft) = 144 W (in.) × H (in.)
Internal Liner Deduction: Acoustic duct liner lines all four interior walls. Subtract twice the liner thickness ( t l i n e r t_{liner} t l in er ) from each nominal dimension: W n e t = W n o m i n a l − ( 2 × t l i n e r ) , H n e t = H n o m i n a l − ( 2 × t l i n e r ) W_{net} = W_{nominal} - (2 \times t_{liner}), \quad H_{net} = H_{nominal} - (2 \times t_{liner}) W n e t = W n o mina l − ( 2 × t l in er ) , H n e t = H n o mina l − ( 2 × t l in er ) A n e t (sq ft) = [ W n o m i n a l − 2 t l i n e r ] × [ H n o m i n a l − 2 t l i n e r ] 144 A_{net}\text{ (sq ft)} = \frac{[W_{nominal} - 2t_{liner}] \times [H_{nominal} - 2t_{liner}]}{144} A n e t (sq ft) = 144 [ W n o mina l − 2 t l in er ] × [ H n o mina l − 2 t l in er ]
2. Round Ducts A (sq ft) = π × D 2 4 × 144 = π × D 2 576 ≈ D 2 183.35 A\text{ (sq ft)} = \frac{\pi \times D^2}{4 \times 144} = \frac{\pi \times D^2}{576} \approx \frac{D^2}{183.35} A (sq ft) = 4 × 144 π × D 2 = 576 π × D 2 ≈ 183.35 D 2
Or in terms of radius r = D / 2 r = D/2 r = D /2 : A (sq ft) = π × r 2 144 A\text{ (sq ft)} = \frac{\pi \times r^2}{144} A (sq ft) = 144 π × r 2
Internal Liner Deduction: D n e t = D n o m i n a l − ( 2 × t l i n e r ) D_{net} = D_{nominal} - (2 \times t_{liner}) D n e t = D n o mina l − ( 2 × t l in er ) A n e t (sq ft) = π × ( D n o m i n a l − 2 t l i n e r ) 2 576 A_{net}\text{ (sq ft)} = \frac{\pi \times (D_{nominal} - 2t_{liner})^2}{576} A n e t (sq ft) = 576 π × ( D n o mina l − 2 t l in er ) 2
3. Flat Oval Ducts
Flat oval ductwork consists of a rectangular center section flanked by two semicircular ends:
Let a a a = Minor internal axis (height/depth in inches)
Let A m a j o r A_{major} A maj or = Major internal axis (width in inches) A (sq ft) = ( π × a 2 4 ) + [ a × ( A m a j o r − a ) ] 144 A\text{ (sq ft)} = \frac{\left( \frac{\pi \times a^2}{4} \right) + \left[ a \times (A_{major} - a) \right]}{144} A (sq ft) = 144 ( 4 π × a 2 ) + [ a × ( A maj or − a ) ]
- 6. Step-by-Step Worked Field Numerical Examples
- Example 1: Standard Air Calculation in a Rectangular Supply Main
Scenario: A technician performs an equal-area Pitot-tube traverse on a 30 in. × 16 in. 30\text{ in.} \times 16\text{ in.} 30 in. × 16 in. unlined rectangular supply duct at standard conditions. Each point's velocity pressure has been converted to velocity before averaging, producing a representative mean velocity of 1 , 878.5 FPM 1,878.5\text{ FPM} 1 , 878.5 FPM . Calculate total airflow.
Calculate internal cross-sectional area ( A A A ): A = 30 × 16 144 = 480 144 = 3.333 sq ft A = \frac{30 \times 16}{144} = \frac{480}{144} = 3.333\text{ sq ft} A = 144 30 × 16 = 144 480 = 3.333 sq ft
Use the point-by-point mean velocity: V a v g = 1 , 878.5 FPM V_{avg} = 1,878.5\text{ FPM} V a vg = 1 , 878.5 FPM
Calculate volumetric flow ( Q Q Q ): Q = A × V a v g = 3.333 sq ft × 1 , 878.5 FPM = 6 , 261 CFM Q = A \times V_{avg} = 3.333\text{ sq ft} \times 1,878.5\text{ FPM} = \mathbf{6,261\text{ CFM}} Q = A × V a vg = 3.333 sq ft × 1 , 878.5 FPM = 6 , 261 CFM
Do not average velocity pressures and then take one square root; the square-root conversion must be performed at each equal-area point before velocities are averaged.
Example 2: Non-Standard Air Density Correction at High Altitude and Heating Temperature
Scenario: A discharge heating air duct measuring 36 in. × 20 in. 36\text{ in.} \times 20\text{ in.} 36 in. × 20 in. is traversed on a project in Denver, CO (elevation 5 , 280 ft 5,280\text{ ft} 5 , 280 ft , measured barometric pressure 24.80 in. Hg 24.80\text{ in. Hg} 24.80 in. Hg ). The air temperature in the duct is 125 ∘ F 125^\circ\text{F} 12 5 ∘ F . The measured velocity pressure is V p = 0.18 in. w.g. V_p = 0.18\text{ in. w.g.} V p = 0.18 in. w.g. Calculate the actual airflow in CFM.
Calculate Internal Area ( A A A ): A = 36 × 20 144 = 720 144 = 5.00 sq ft A = \frac{36 \times 20}{144} = \frac{720}{144} = 5.00\text{ sq ft} A = 144 36 × 20 = 144 720 = 5.00 sq ft
Calculate Density Correction Factor ( K d K_d K d ): K d = ( 530 460 + 125 ) × ( 24.80 29.92 ) = ( 530 585 ) × 0.82888 = 0.90598 × 0.82888 = 0.7509 K_d = \left( \frac{530}{460 + 125} \right) \times \left( \frac{24.80}{29.92} \right) = \left( \frac{530}{585} \right) \times 0.82888 = 0.90598 \times 0.82888 = \mathbf{0.7509} K d = ( 460 + 125 530 ) × ( 29.92 24.80 ) = ( 585 530 ) × 0.82888 = 0.90598 × 0.82888 = 0.7509
Calculate Actual Density ( ρ a c t u a l \rho_{actual} ρ a c t u a l ): ρ a c t u a l = 0.075 × 0.7509 = 0.05632 lb/ft 3 \rho_{actual} = 0.075 \times 0.7509 = 0.05632\text{ lb/ft}^3 ρ a c t u a l = 0.075 × 0.7509 = 0.05632 lb/ft 3
Calculate Density-Corrected Velocity ( V V V ): V = 4005 × 0.18 0.7509 = 4005 × 0.23971 = 4005 × 0.48960 = 1961 FPM V = 4005 \times \sqrt{\frac{0.18}{0.7509}} = 4005 \times \sqrt{0.23971} = 4005 \times 0.48960 = \mathbf{1961\text{ FPM}} V = 4005 × 0.7509 0.18 = 4005 × 0.23971 = 4005 × 0.48960 = 1961 FPM (Note: The uncorrected standard formula would yield 4005 × 0.18 = 1699 FPM 4005 \times \sqrt{0.18} = 1699\text{ FPM} 4005 × 0.18 = 1699 FPM , creating an uncorrected error of 13.4 % 13.4\% 13.4% !)
Calculate Total Actual Airflow ( Q Q Q ): Q = 5.00 sq ft × 1961 FPM = 9805 CFM Q = 5.00\text{ sq ft} \times 1961\text{ FPM} = \mathbf{9805\text{ CFM}} Q = 5.00 sq ft × 1961 FPM = 9805 CFM
Example 3: Round Spiral Duct with Internal Acoustic Liner
Scenario: A 22 in. 22\text{ in.} 22 in. nominal diameter round supply duct is lined internally with 1.0 in. 1.0\text{ in.} 1.0 in. fiberglass acoustic insulation. An average traverse velocity of 1350 FPM 1350\text{ FPM} 1350 FPM is measured under standard air conditions. Determine the actual airflow.
Determine Net Internal Diameter ( D n e t D_{net} D n e t ): D n e t = 22 in. − ( 2 × 1.0 in. ) = 20.0 in. D_{net} = 22\text{ in.} - (2 \times 1.0\text{ in.}) = 20.0\text{ in.} D n e t = 22 in. − ( 2 × 1.0 in. ) = 20.0 in.
Calculate Net Cross-Sectional Area ( A n e t A_{net} A n e t ): A n e t = π × ( 20.0 ) 2 576 = 3.14159 × 400 576 = 1256.64 576 = 2.182 sq ft A_{net} = \frac{\pi \times (20.0)^2}{576} = \frac{3.14159 \times 400}{576} = \frac{1256.64}{576} = 2.182\text{ sq ft} A n e t = 576 π × ( 20.0 ) 2 = 576 3.14159 × 400 = 576 1256.64 = 2.182 sq ft
Calculate Volumetric Flow Rate ( Q Q Q ): Q = A n e t × V = 2.182 sq ft × 1350 FPM = 2946 CFM Q = A_{net} \times V = 2.182\text{ sq ft} \times 1350\text{ FPM} = \mathbf{2946\text{ CFM}} Q = A n e t × V = 2.182 sq ft × 1350 FPM = 2946 CFM