Study guide
6.1 Traverse Locations, Disturbances, and Point Layout
NEBB Testing, Adjusting and Balancing Certified Technician CT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Role, Documents, and Readiness
1.1 NEBB TAB CT Role, CP Guidance, Standards, and Data Integrity 1.2 Interpreting Plans, Schedules, and Control Sequences 1.3 Field Verification, Pre-TAB Readiness, and Deficiencies
2 Chapter 2: TAB Math and Heat Transfer
2.1 TAB Mathematics, Units, Ratios, and Formula Discipline 2.2 Air-Side Sensible, Latent, and Total Heat Transfer 2.3 Hydronic Heat Transfer, Glycol Corrections, and Coil Cross-Checks
3 Chapter 3: Psychrometrics
3.1 Psychrometric Properties and Reading the Chart 3.2 Psychrometric Processes, Air Mixing, and Coil Diagnostics
4 Chapter 4: TAB Instrumentation and Measurement Quality
4.1 Pressure Instruments, Manometers, Zeroing, and Tubing 4.2 Airflow Instruments: Hoods, Anemometers, and Pitot Tubes 4.3 Hydronic Pressure and Temperature Instruments 4.4 Electrical and Rotational Instruments
5 Chapter 5: Air Systems and Airflow Fundamentals
5.1 Air-System Configurations and System Relationships 5.2 Airflow Continuity, Standard Air, Density, and Velocity 5.3 Duct Geometry and Worked Airflow Calculations
6 Chapter 6: Duct Traverses
6.1 Traverse Locations, Disturbances, and Point Layout 6.2 Traverse Velocity Conversion and Airflow Calculation
7 Chapter 7: Terminal Measurements and Air Balancing
7.1 Terminal Devices, Effective Area, and Capture-Hood Checks 7.2 Proportional Air Balancing and Final Verification 7.3 Outside Air, Exhaust Balancing, and Building Pressurization
8 Chapter 8: Fans, Motors, and Drives
8.1 Fan Types, Performance Curves, and Rotation 8.2 Fan Affinity Laws, Pressure, and Power 8.3 Motors, Single- and Three-Phase Measurements, and Loading 8.4 Belts, Sheaves, Alignment, and Variable Frequency Drives
9 Chapter 9: HVAC Controls and VAV Systems
9.1 HVAC Control Fundamentals, Signals, and Test States 9.2 VAV Terminal Types, Airflow Sensors, and Calibration 9.3 VAV System Balancing, Diversity, and Static-Pressure Control
10 Chapter 10: Hydronic System Fundamentals
10.1 Hydronic Pressure, Head, Open and Closed Systems, and Resistance 10.2 Expansion Tanks, Point of No Pressure Change, and Fill Pressure
11 Chapter 11: Pumps and Hydronic Balancing
11.1 Centrifugal Pumps, Pump Curves, and Pump Affinity Laws 11.2 Balancing Valves, Circuit Setters, Strainers, and Hydronic Procedures
12 Chapter 12: Reporting, Safety, and Problem Solving
12.1 Project Acceptance Criteria, Data Traceability, and Certified Reports 12.2 Field Safety, Electrical Boundaries, Pressure, and Access 12.3 Integrated TAB Problem Solving and Measurement Cross-Checks
6.1 Traverse Locations, Disturbances, and Point Layout
Key Takeaways Explain This Topic AI
Choose the straightest accessible plane and document unavoidable upstream or downstream disturbances.
Equivalent diameter helps express straight-run guidance for rectangular ducts but does not erase swirl or nonuniform profiles.
Log-Tchebycheff and equal-area layouts are recognized methods; use the method and point count required by the governing procedure.
Round ducts normally require measurements on more than one diameter so a single asymmetric profile does not control the result.
Last updated: August 2026
- Traverse Location and Point Layout
- Why a traverse needs many points
Velocity is not uniform across a duct. Wall friction slows the boundary layer, fittings create gradients and swirl, and fan discharge can produce concentrated jets. A single centerline reading therefore cannot represent total flow. A duct traverse samples defined locations across the cross-section, converts each velocity-pressure reading to velocity, and combines the readings according to the selected method.
Select the plane from the governing procedure
The best plane is a straight, constant-area duct segment away from elbows, transitions, dampers, branches, fan discharge, and other disturbances. The required upstream and downstream clearances depend on the applicable standard or method and the disturbance. A commonly encountered ideal criterion is 7.5 equivalent diameters downstream and 2.5 diameters upstream, but it must not be presented as the minimum for every procedure or field condition.
For the hydraulic-diameter calculation used by many TAB procedures for rectangular duct:
De = 2WH / (W + H)
For a 30-inch by 20-inch duct, De = (2 × 30 × 20) / 50 = 24 inches, or 2 feet. If the selected procedure calls for 7.5 De downstream, that distance is 15 feet. This calculation applies the stated criterion; it does not create one where the governing procedure specifies something else.
Inspect the candidate plane. Avoid a location with visible swirl, pulsation, stratification, loose liner, an obstructed probe path, or leakage at test holes. Confirm internal dimensions rather than relying only on nominal drawing size. Record the actual distances to disturbances and the reason for choosing the plane. When an ideal plane is unavailable, use the best permitted location, increase diagnostic checks as appropriate, compare with an independent method, and disclose the limitation.
Rectangular-duct layouts
Point coordinates come from the named traverse method. Log-Tchebycheff layouts place more points near the walls so the sample represents boundary-layer effects. Equal-area layouts place each reading at the representative location of an equal-area cell. Either label is incomplete without the actual coordinate table and required number of points from the governing procedure.
Do not invent coordinates in the field. Calculate each insertion depth from the measured internal dimension and the published fractional location. Mark the probe stem, keep it normal to the duct wall, and account for liner thickness and wall offset. A point accidentally placed against a wall, behind a turning vane, or outside the intended cell is not a valid sample.
Round-duct layouts
Round-duct procedures commonly use readings along two perpendicular diameters so both directions of the velocity field are represented. The number and radial positions depend on the selected equal-area or Log-T method and duct size. Follow the applicable coordinate table rather than assuming that one fixed count—such as six, eight, or ten points per diameter—always governs.
Use access holes that allow the probe to reach each required position without contacting the opposite wall. Align the impact opening into the airstream. If yaw or pitch is suspected, rotate and compare the probe cautiously under the instrument procedure; severe directional flow is also evidence that the location may be poor.
Field execution
Before collecting data, verify system mode and stability, inspect and zero the manometer, leak-check tubing, and confirm that the pressure range can resolve the expected signal. At every point:
- place the probe at the calculated coordinate;
- align it with the local flow as the method permits;
- allow the reading to stabilize;
- record the signed velocity pressure and point identity; and
investigate negative, erratic, or implausible values rather than changing them.
Seal test holes after the traverse. A defensible report identifies duct dimensions, net area, point method, plane location, disturbances, instrument, individual readings, air-density treatment, average velocity, and calculated airflow.
Quality checks
Convert velocity pressure to velocity before averaging because velocity varies with the square root of velocity pressure. Compare the traverse total with fan inlet or outlet readings, terminal sums, an airflow station, or another suitable method. The readings need not match exactly, but a material difference requires investigation of leakage, diversity, density, simultaneous operating conditions, instrument setup, or poor profile. Repeating a traverse in the same bad plane does not remove the underlying limitation.
Location-versus-layout distinction
A correct point grid cannot cure a severely disturbed plane, and a long straight run cannot cure wrong point coordinates. Evaluate these independently. The report should allow another technician to locate the plane, reconstruct every insertion depth, and understand any compromise.