Study guide
7.2 Proportional Air Balancing and Final Verification
NEBB Testing, Adjusting and Balancing Certified Technician CT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Role, Documents, and Readiness
1.1 NEBB TAB CT Role, CP Guidance, Standards, and Data Integrity 1.2 Interpreting Plans, Schedules, and Control Sequences 1.3 Field Verification, Pre-TAB Readiness, and Deficiencies
2 Chapter 2: TAB Math and Heat Transfer
2.1 TAB Mathematics, Units, Ratios, and Formula Discipline 2.2 Air-Side Sensible, Latent, and Total Heat Transfer 2.3 Hydronic Heat Transfer, Glycol Corrections, and Coil Cross-Checks
3 Chapter 3: Psychrometrics
3.1 Psychrometric Properties and Reading the Chart 3.2 Psychrometric Processes, Air Mixing, and Coil Diagnostics
4 Chapter 4: TAB Instrumentation and Measurement Quality
4.1 Pressure Instruments, Manometers, Zeroing, and Tubing 4.2 Airflow Instruments: Hoods, Anemometers, and Pitot Tubes 4.3 Hydronic Pressure and Temperature Instruments 4.4 Electrical and Rotational Instruments
5 Chapter 5: Air Systems and Airflow Fundamentals
5.1 Air-System Configurations and System Relationships 5.2 Airflow Continuity, Standard Air, Density, and Velocity 5.3 Duct Geometry and Worked Airflow Calculations
6 Chapter 6: Duct Traverses
6.1 Traverse Locations, Disturbances, and Point Layout 6.2 Traverse Velocity Conversion and Airflow Calculation
7 Chapter 7: Terminal Measurements and Air Balancing
7.1 Terminal Devices, Effective Area, and Capture-Hood Checks 7.2 Proportional Air Balancing and Final Verification 7.3 Outside Air, Exhaust Balancing, and Building Pressurization
8 Chapter 8: Fans, Motors, and Drives
8.1 Fan Types, Performance Curves, and Rotation 8.2 Fan Affinity Laws, Pressure, and Power 8.3 Motors, Single- and Three-Phase Measurements, and Loading 8.4 Belts, Sheaves, Alignment, and Variable Frequency Drives
9 Chapter 9: HVAC Controls and VAV Systems
9.1 HVAC Control Fundamentals, Signals, and Test States 9.2 VAV Terminal Types, Airflow Sensors, and Calibration 9.3 VAV System Balancing, Diversity, and Static-Pressure Control
10 Chapter 10: Hydronic System Fundamentals
10.1 Hydronic Pressure, Head, Open and Closed Systems, and Resistance 10.2 Expansion Tanks, Point of No Pressure Change, and Fill Pressure
11 Chapter 11: Pumps and Hydronic Balancing
11.1 Centrifugal Pumps, Pump Curves, and Pump Affinity Laws 11.2 Balancing Valves, Circuit Setters, Strainers, and Hydronic Procedures
12 Chapter 12: Reporting, Safety, and Problem Solving
12.1 Project Acceptance Criteria, Data Traceability, and Certified Reports 12.2 Field Safety, Electrical Boundaries, Pressure, and Access 12.3 Integrated TAB Problem Solving and Measurement Cross-Checks
7.2 Proportional Air Balancing and Final Verification
Key Takeaways Explain This Topic AI
Percent of design is measured flow divided by design flow; under a specified proportional method, the lowest verified ratio is the initial index.
Remeasure the index as higher-ratio paths are adjusted because every damper change redistributes pressure and flow.
Proportional agreement does not prove adequate total airflow, and it never authorizes a fan-speed change beyond equipment or power limits.
Final acceptance uses the project criterion and a complete repeat sweep after authorized system adjustments and control restoration.
Last updated: August 2026
- Proportional Air Balancing and Final Verification
- Ratios reveal distribution
Proportional balancing compares each measured flow with its own design value:
ratio = measured flow / design flow
A 240 CFM terminal with a 300 CFM design has a ratio of 0.80, or 80% of design. A 480 CFM terminal with a 400 CFM design has a ratio of 1.20. The absolute flows differ, but the ratios show how the distribution compares with design.
The proportional method applies when the governing procedure calls for it and the system can be held in a stable, defined condition. It assumes that relative path resistance remains reasonably consistent while the group is adjusted. Controls, fan speed, doors, filters, and other system conditions must not drift between readings.
Establish the test state
Review the project documents and approved procedure before positioning dampers or controls. For a constant-volume branch, the initial condition commonly places the relevant manual balancing dampers open. For VAV systems, the selected boxes and fan state must reflect the approved diversity or test scenario; commanding every box to maximum is not automatically correct.
Record fan speed, filter and coil condition, terminal commands, control overrides, doors, and any exhaust or return modes that affect the branch. Verify that the measurement method is appropriate for each terminal and that design values come from the current schedule.
Perform an initial sweep without random adjustment. Calculate the ratio for every terminal and organize the results by system topology: outlets within a branch, branches within a riser, and risers within the system.
Select and protect the index path
Under a standard proportional procedure, the lowest measured-to-design ratio in the group is the initial index . Its balancing device remains open while higher-ratio paths are throttled. This avoids adding resistance to the path that already has the least available flow.
The index is the measured lowest-ratio path under the stated condition; it is not automatically the physically farthest outlet. A crushed flex duct, closed branch damper, poor takeoff, wrong design value, or bad hood setup can create an apparent index. Investigate an unusually low result before using it as the reference.
As other paths are throttled, the index flow changes. Remeasure it rather than treating the initial ratio as fixed. Work through the group in the sequence required by the procedure and system layout. The goal is agreement within the project-defined proportional criterion, not mathematical perfection.
Worked proportional example
Four outlets have these initial values:
- Outlet Design CFM Measured CFM Ratio
- A 500 600 120%
- B 400 360 90%
- C 500 400 80%
- D 300 210 70%
Outlet D is the initial index because 210/300 = 70%, the lowest ratio. Leave its manual balancing device open under this method. Adjust the higher-ratio paths in the prescribed sequence while repeatedly measuring D and the path being adjusted. If D rises to 75%, the comparison target for a 500 CFM outlet is 375 CFM and for a 400 CFM outlet is 300 CFM.
Those values are temporary proportional targets, not final acceptance values. The exact response cannot be predicted from the original readings because each adjustment changes the pressure distribution. Measure the new condition rather than inventing a step-by-step flow increase.
Total flow and fan adjustment boundary
A proportioned system can still be globally low. If every outlet is near 82% of design, the distribution relationship may be satisfactory while total airflow is inadequate. Do not automatically raise speed by 1/0.82. That simple ratio is only an affinity-law forecast for the same fan and comparable system; it may demand an unsafe speed, pressure, or power increase.
Before any authorized fan change:
- verify the total-flow measurement and system mode;
- confirm rotation, filters, coils, dampers, leakage, and control positions;
- locate the current fan operating point on the correct curve;
- predict airflow, pressure, and brake horsepower at the proposed speed;
- check motor, VFD, sheave, fan, bearing, vibration, and pressure limits; and
obtain the required authorization.
If the needed flow cannot be reached within those limits, preserve the measured results and report the deficiency. Do not close the index path, exceed equipment limits, or alter the design value to make the report pass.
Final sweep and restoration
After branch, riser, and total adjustments, perform a complete final sweep in the specified operating state. Recheck index and critical paths after every upstream or fan change. Apply the acceptance criterion in the contract documents; a remembered plus-or-minus-ten-percent example is not a universal rule.
Record design, initial, and final airflow; percent of design; damper position; instrument and method; fan speed; pressure and motor data; test mode; and unresolved limitations. Mark or lock final manual settings only as the project permits.
Finally, release all temporary overrides and verify normal automatic operation. Test any required minimum, maximum, economizer, exhaust, or diversity modes. A branch that is balanced only under an abandoned override is not complete.