Study guide

8.4 Motor Surge Test & Current Imbalance

NETA ETT Level II Certified Assistant Technician Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide

2 Chapter 1: Electrical Safety

2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications

3 Chapter 2: Power Systems Theory

3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions

4 Chapter 3: Protection & Device Fundamentals

4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies

5 Chapter 4: Insulation Resistance Testing

5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography

6 Chapter 5: Withstand & Power-Factor Testing

6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating

7 Chapter 6: Transformer Testing

7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests

8 Chapter 7: CT, Relay & Motor Testing

8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables

9 Chapter 8: Switchgear & Breaker Testing

9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures

10 Chapter 9: Grounding, Batteries & Protective Devices

10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance

11 Chapter 10: Systems & Commissioning

11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow

8.4 Motor Surge Test & Current Imbalance

Key Takeaways Explain This Topic AI

A motor surge (impulse) test discharges a capacitor into the winding to produce a fast-rise voltage impulse (0.1 to 0.2 microsecond rise time per IEEE 522-2023) and compares the ringing waveform phase-to-phase; a frequency shift indicates a turn-to-turn short.

Surge testing detects turn-to-turn and coil-to-coil insulation weaknesses that IR, PI, DAR, and hipot tests cannot see, because DC and power-frequency tests do not stress inter-turn insulation.

ANSI/EASA AR100-2020 surge test voltage is V = 2E + 1000 V (E = rated line-to-line RMS); for used/maintenance machines the test voltage is reduced to 75% of the formula value.

Motor current imbalance is computed as 100 x (max deviation from average) / average; an imbalance greater than 10% is a NEMA red flag.

NEMA MG-1 derates a motor on voltage unbalance: 3% unbalance requires derating to about 0.88 of rated load, and operation above 5% is not recommended.

Last updated: August 2026

8.4.1 Motor Surge (Impulse) Comparison Test

The surge test detects turn-to-turn insulation weaknesses in a motor or generator stator winding that no DC insulation test can see. A capacitor is discharged into the winding, producing a fast-rise, high-frequency voltage impulse (typical rise time 0.1 to 0.2 microseconds per IEEE 522-2023). The resulting damped RLC oscillation is displayed and compared phase-to-phase or to a baseline trace.

Why it works: the surge pulse's high-frequency components see the winding as a distributed L-C network, and the ringing frequency is a function of the winding inductance. If turn-to-turn insulation breaks down during the pulse, the arc shorts turns together, the inductance drops, and the ringing frequency increases — the waveform shifts to the left (a zero-crossing shift). Modern instruments (Baker AWA, Electrom iTIG) auto-compare traces using the Error Area Ratio (EAR) and flag deviations above a threshold.

Test voltage. ANSI/EASA AR100-2020 uses V = 2E + 1000 V (E = rated line-to-line RMS). IEEE 522-2023 defines a withstand envelope based on rise time: at 0.1 to 0.2 microsecond rise time the recommended test voltage is 3.5 per-unit , where 1 pu = (sqrt(2) / sqrt(3)) x V_L (peak line-to-ground voltage). For used or maintenance machines the test voltage is reduced to 75% of the formula value.

  • Standard Formula / envelope Applies to
  • ANSI/EASA AR100-2020 V = 2E + 1000 V Random and form wound, repair and field
  • IEEE 522-2023 3.5 pu at 0.1 to 0.2 us rise time Form-wound stator coils
  • IEC 60034-15 Ed.4 U'P = 0.65(4U_N + 5 kV), T1 = 0.2 us Form-wound sample coils

A minimum of roughly 350 to 500 V per turn is needed to arc a turn fault (Paschen's minimum). The surge test is the only standard test that reliably catches turn-to-turn weaknesses before they short to ground in service.

8.4.2 What Surge Testing Detects That IR/PI Cannot

Insulation resistance (IR), polarization index (PI), and dielectric absorption ratio (DAR) tests apply DC and measure the ground-wall insulation — the insulation between the winding and the stator core. They cannot see the insulation between adjacent turns, because the DC resistance of a copper turn is tiny and the turn-to-turn voltage from a DC megger is negligible.

Surge testing applies a fast-front impulse whose voltage divides across turns according to the winding's high-frequency surge impedance. The turn-to-turn stress can reach hundreds of volts per turn — enough to break down weakened turn insulation and show on the trace. So:

IR/PI/DAR: ground-wall (phase-to-ground) insulation only.

Surge: turn-to-turn, coil-to-coil, and phase-to-phase insulation.

Hipot (AC or DC): ground-wall dielectric withstand; does not stress turn-to-turn at power frequency.

NETA MTS and most motor repair specifications call for both IR/PI and a surge comparison test on form-wound and most random-wound machines above a few kW, because the two tests look at different failure modes. A motor can pass IR/PI with a healthy ground wall and still have turn-to-turn weaknesses that the surge test will catch.

8.4.3 Motor Current Imbalance Test

Run the motor at its normal load and measure the current in all three phases with a clamp meter or power analyzer. Compute the percent current imbalance:

% imbalance = 100 x (max deviation from average) / average

Worked example: phases read 60 A, 60 A, and 50 A. Average = (60 + 60 + 50) / 3 = 56.7 A. Max deviation = 56.7 - 50 = 6.7 A. Imbalance = 100 x 6.7 / 56.7 = 11.8% .

A current imbalance greater than 10% is a red flag per NEMA and IEEE 1068. Causes include:

Supply voltage imbalance (a small voltage imbalance produces a 6 to 10x larger current imbalance).

A single high-resistance connection or a failing contactor pole.

A winding turn fault (the surge test confirms this).

Unbalanced single-phase loading on the same feeder.

Always compare the three phase voltages and a thermal image before concluding the motor is bad — a voltage imbalance of just 1% at the terminals can show up as a 6 to 10% current imbalance at the motor.

8.4.4 NEMA MG-1 Voltage Unbalance Derating

NEMA MG-1 (sections 14.35 / 14.36 / 20.56) defines the voltage unbalance formula and a derating curve that limits how much load the motor can carry on an unbalanced supply.

% V_unbalance = 100 x (max voltage deviation from average) / average voltage

  • Voltage unbalance Derating factor
  • 0% 1.00
  • 1% ~0.99
  • 2% ~0.955
  • 3% ~0.88
  • 4% ~0.75
  • 5% ~0.58

NEMA does not recommend operation above 5% voltage unbalance. Unbalance generates negative-sequence currents that rotate opposite to the rotor, inducing extra rotor heating. A 1% voltage unbalance typically causes about a 2% temperature rise; at 5.4% voltage unbalance a test motor showed 40% current unbalance and a 40 degree C temperature-rise increase. NEMA recommends overload devices responsive to I_maximum rather than I_average when unbalance is anticipated.

8.4.5 Acceptance and Trending

Acceptance: compare the measured surge traces phase-to-phase and to the manufacturer's baseline (or to a sister machine). Acceptance current imbalance is typically 5% or less at rated load. Trend upward over time.

Always pair surge with IR/PI:

New motor: IR meets the IEEE 43 minimum for the insulation class, PI >= 2.0 (Class B and above), and surge traces match phase-to-phase within the EAR limit.

In-service motor: trend IR/PI over months; trend the surge trace EAR; trend current imbalance. A rising current imbalance with a stable voltage unbalance points to a winding problem; a stable current imbalance with a rising voltage unbalance points to the supply.

  • Test Insulation it stresses Failure mode it catches
  • IR / PI / DAR Ground-wall (phase-to-ground) Ground-wall degradation, moisture, contamination
  • Hipot (AC/DC) Ground-wall dielectric withstand Ground-wall breakdown
  • Surge comparison Turn-to-turn, coil-to-coil, phase-to-phase Turn-to-turn shorts, coil weaknesses
  • Current imbalance N/A (running test) Winding faults, supply imbalance, contactor faults